1996 TOYOTA RAV4 Service Repair Manual

CO0BE−01
S01292Drain Plug CO−2
− COOLINGCOOLANT
1996 RAV4 (RM447U)
REPLACEMENT
1. DRAIN ENGINE COOLANT
(a) Remove the radiator cap.
CAUTION:
To avoid the danger of being burned, do not remove the ra-
diator cap while the engine and radiator are still hot, as fluid
and steam can be blown out under pressure.
(b) Loosen the radiator drain plug (on the left side of the ra-
diator lower tank) and engine drain plug (on the left rear
of the cylinder block), and drain the coolant.
(c) Close the drain plugs.
Torque: Engine drain plug
25 N·m (250 kgf·cm, 18 ft·lbf)
2. FILL ENGINE COOLANT
(a) Slowly fill the system with coolant.
Use a good brand of ethylene−glycol base coolant
and mix it according to the manufacture’s direc-
tions.
Using coolant which includes more than 50 % ethyl-
ene−glycol (but not more than 70 %) is recom-
mended.
NOTICE:
Do not use an alcohol type coolant.
The coolant should be mixed with demineralized wa-
ter or distilled water.
Capacity (w/ Heater):
M/T: 8.0 liters (8.5 US qts, 7.0 lmp. qts)
A/T: 7.7 liters (8.1 US qts, 6.8 lmp. qts)
(b) Install radiator cap.
(c) Start the engine, and bleed the cooling system.
(d) Refill the radiator reservoir with coolant until it reaches the
”FULL” line.
3. CHECK ENGINE COOLANT FOR LEAKS

CO0BF−03
S06209
No.3 ABS Actuator Bracket
Engine Wire
Generator
Generator
Drive Belt
PS Pump
Drive BeltGround Strap
Connector
Generator
BracketPS Reservoir Bracket
PS Reservoir
RH Engine Mounting Insulator
RH Engine Mounting Bracket
RH Engine
Under Cover
N·m (kgf·cm, ft·lbf): Specified Torque
37 (380, 27)
52 (530, 38)
52 (530, 38)
52 (530, 38)
52 (530, 38)
52 (530, 38)52 (530, 38)
− COOLINGWATER PUMP
CO−3
1996 RAV4 (RM447U)
WATER PUMP
COMPONENTS

CO−4
− COOLINGWATER PUMP
1996 RAV4 (RM447U)

CO0BG−02
S01613
P15462
P15546
1
3
2
P15463
Disconnect
− COOLINGWATER PUMP
CO−5
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE RH ENGINE UNDER COVER
2. DRAIN ENGINE COOLANT
3. REMOVE TIMING BELT (See page EM−15)
4. DISCONNECT LOWER RADIATOR HOSE FROM
WATER INLET
5. REMOVE TIMING BELT TENSION SPRING AND NO.2
IDLER PULLEY
6. REMOVE GENERATOR DRIVE BELT ADJUSTING
BAR
(a) Disconnect the crankshaft position sensor connector
clamp.
(b) Remove the bolt and adjusting bar.
7. REMOVE WATER PUMP AND WATER PUMP COVER
ASSEMBLY
(a) Remove the 2 nuts holding the water pump to the water
bypass pipe.
(b) Remove the 3 bolts in the sequence shown.
(c) Disconnect the water pump cover from the water bypass
pipe, and remove the water pump and water pump cover
assembly.
(d) Remove the gasket and 2 O−ring from the water pump
and water bypass pipe.

N00918
CO−6
− COOLINGWATER PUMP
1996 RAV4 (RM447U)
8. REMOVE WATER PUMP FROM WATER PUMP COVER
Remove the 3 bolts, water pump and gasket.

CO0BH−02
CO0877
− COOLINGWATER PUMP
CO−7
1996 RAV4 (RM447U)
INSPECTION
INSPECT WATER PUMP
(a) Visually check the drain hole for coolant leakage.
If leakage is found, replace the water pump.
If engine coolant has leaked onto the timing belt, replace the
timing belt.
(b) Turn the pulley, and check that the water pump bearing
moves smoothly and quietly.
If necessary, replace the water pump.

CO0BI−03
P13480
New O−Ring
New Gasket
P15547
New O−Ring
P15464
Connect
Z16489
3
1
2 CO−8
− COOLINGWATER PUMP
1996 RAV4 (RM447U)
INSTALLATION
1. INSTALL WATER PUMP TO WATER PUMP COVER
Install a new gasket and the water pump with the 3 bolts.
Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
2. INSTALL WATER PUMP AND WATER PUMP COVER
ASSEMBLY
(a) Install new O−ring and gasket to water pump cover.
(b) Install a new O−ring to the water bypass pipe.
(c) Apply soapy water to the O−ring on the water bypass
pipe.
(d) Connect the water pump cover to the water bypass pipe.
Do not install the nuts yet.
(e) Install the water pump with the 3 bolts. Tighten the bolts
in the sequence shown.
Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
(f) Install the 2 nuts holding the water pump cover to the wa-
ter bypass pipe.
Torque: 9.3 N·m (95 kgf·cm, 82 in.·lbf)
3. INSTALL GENERATOR DRIVE BELT ADJUSTING BAR
(a) Install the adjusting bar with the bolt.
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
(b) Connect the crankshaft position sensor connector clamp.
4. INSTALL NO.2 IDLER PULLEY AND TIMING BELT
TENSION SPRING
5. CONNECT LOWER RADIATOR HOSE
6. INSTALL TIMING BELT (See page EM−20)
7. FILL WITH ENGINE COOLANT
8. START ENGINE AND CHECK FOR COOLANT LEAKS
9. INSTALL RH ENGINE UNDER COVER

CO0BJ−01
S01641
Thermostat
 Gasket
Water InletOil Filter
N·m (kgf·cm, ft·lbf): Specified torque
 Non−reusable part
8.8 (90, 78 in.·lbf)
− COOLINGTHERMOSTAT
CO−9
1996 RAV4 (RM447U)
THERMOSTAT
COMPONENTS