1995 TOYOTA SUPRA torque

A340E (2JZ-GTE) AUTOMATIC TRANSMISSIONCOMPONENT PARTS INSTALLATION -
AT-102
(e) Using a hammer, drive in a new spring pin.
(f) Match the manual valve lever indentation with the spacer
hole and calk them together with the punch.
(g) Make sure the shaft rotates smoothly.
29. INSTALL PARKING LOCK PAWL AND ROD
(a) Install the E-ring to the shaft.
(b) Install the parking lock pawl, shaft and spring.
(c) Connect the parking lock rod to the manual valve lever.
(d) Place the parking lock pawl bracket onto the transmission
case and torque the 3 bolts.
Torque: 7 N´m (75 kgf´cm, 65 in.´lbf)

A340E (2JZ-GTE) AUTOMATIC TRANSMISSIONCOMPONENT PARTS INSTALLATION -
AT-104
32. INSTALL VALVE BODY
(a) Align the groove of the manual valve to the pin of the lever.
(b) Install the 20 bolts.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
HINT: Each bolt length (mm, in.) is indicated in the illustra-
tion.
33. INSTALL SOLENOID WIRING
(a) Coat a new O-ring with ATF and install it to the solenoid
wire.
(b) Install the solenoid wiring to the case and install the stop-
per plate.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(c) Connect the 5 solenoid connectors.
(d) Install the clamp with 2 bolts.

A340E (2JZ-GTE) AUTOMATIC TRANSMISSIONCOMPONENT PARTS INSTALLATION -
AT-105
34. INSTALL OIL STRAINER AND GASKETS
Install the oil strainer and torque the 3 bolts.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
35. INSTALL OIL PAN
(a) Install the 3 magnets in the oil pan, as shown.
(b) Remove any packing material and be careful not to drop
oil on the contacting surfaces of the transmission case
and oil pan.
(c) Apply seal packing to the oil pan.
Seal packing:
Part No.08826-00090, THREE BOND 1281 or equiva-
lent
(d) Install and torque the 19 bolts.
Torque: 17 N´m (75 kgf´cm, 65 in.´lbf)
36. INSTALL SPEEDOMETER DRIVE GEAR

A340E (2JZ-GTE) AUTOMATIC TRANSMISSIONCOMPONENT PARTS INSTALLATION -
AT-106
37. INSTALL EXTENSION HOUSING
(a) Clean the threads of the bolts and case with white gaso-
line.
(b) Apply seal packing to the extension housing.
Seal packing:
Part No.08826-00090, THREE BOND 1281 or equiva-
lent
(c) Apply seal packing or equivalent to the 6 bolts.
Seal packing:
Part No.08833-00070, THREE BOND 1324 or equiva-
lent
(d) Install and torque the 6 bolts.
Torque: 34 N´m (345 kgf´cm, 25 ft´lbf)
HINT: Each bolt length is indicated below.
Bolt length:
Bolt A: 35 mm (1.378 in.)
Bolt B: 45 mm (1.772 in.)
38. INSTALL TRANSMISSION OUTPUT FLANGE
(a) Install a new oil seal to the output flange.
(b) Install the output flange and 2 washers.
(c) Using SST, install a new nut.
SST 09060-20100
Torque: 123 N´m (1,250 kgf´cm, 90 ft´lbf)
HINT: Shift the manual valve lever to the P position.
(d) Using a hammer and chisel, stake the nut.

A340E (2JZ-GTE) AUTOMATIC TRANSMISSIONCOMPONENT PARTS INSTALLATION -
AT-107
39. REMOVE TRANSMISSION CASE FROM OVERHAUL
ATTACHMENT
40. INSTALL TRANSMISSION HOUSING
(a) Clean the threads of the bolts and case with white gaso-
line.
(b) Apply seal packing or equivalent to the 6 bolts.
Seal packing:
Part No.08833-00070, THREE BOND 1324 or equiva-
lent
(c) Install and torque the 6 bolts.
Torque:
14 mm bolt: 34 N´m (345 kgf´cm, 25 ft´lbf)
17 mm bolt: 57 N´m (580 kgf´cm, 42 ft´lbf)
41. INSTALL O/D DIRECT CLUTCH SPEED SENSOR
(a) Coat a new O-ring with ATF and install it to the speed sen-
sor.
(b) Install the speed sensor.
(c) Install and torque the bolts.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
42. INSTALL NO.2 VEHICLE SPEED SENSOR
(a) Coat a new O-ring with ATF and install it to the speed sen-
sor.
(b) Install the speed sensor.
(c) Install and torque the bolts.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
43. INSTALL NO.1 VEHICLE SPEED SENSOR
(a) Coat a new O-ring with ATF and install it to the No.1 ve-
hicle speed sensor.
(b) Install the No.1 vehicle speed sensor.
(c) Install and torque the bolt.
Torque: 16 N´m (160 kgf´cm, 12 ft´lbf)

A340E (2JZ-GTE) AUTOMATIC TRANSMISSIONCOMPONENT PARTS INSTALLATION -
AT-108
44. INSTALL UNIONS
(a) Coat 2 new O-rings with ATF and install them to each
union.
(b) Install each union.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
45. INSTALL OIL TEMPERATURE SENSOR
(a) Coat a new O-ring with ATF and install it to the oil temp.
sensor.
(b) Install the oil temp. sensor.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
46. INSTALL PARK/NEUTRAL POSITION SWITCH
(a) Using the control shaft lever, fully turn the manual lever
shaft back and return 2 notches. It is now in neutral.
(b) Insert the park/neutral position switch onto the manual
valve lever shaft and temporarily tighten the adjusting
bolt.
(c) Install the grommet and a new lock washer. Install and
torque the nut.
Torque: 7 N´m (70 kgf´cm, 61 in.´lbf)
(d) Clean the threads of the adjusting bolt and case with
white gasoline.
(e) Apply seal packing or equivalent to the adjusting bolt.
Seal packing:
Part No.08833-00070, THREE BOND 1324 or equiva-
lent
(f) Align the neutral basic line and the switch groove, and
tighten the adjusting bolt.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)

A340E (2JZ-GTE) AUTOMATIC TRANSMISSIONCOMPONENT PARTS INSTALLATION -
AT-109
(g) Using a screwdriver, bend the tabs of the lock washer.
HINT: Bend at least 2 of the lock washer tabs.
47. INSTALL CONTROL SHAFT LEVER
Torque: 16 N´m (160 kgf´cm, 12 ft´lbf)

A340E(Others) AUTOMATIC TRANSMISSIONDESCRIPTION -
AT-1
DESCRIPTION
GENERAL DESCRIPTION
The A340E is a 4-speed, Electronically Controlled Transmission developed for use with high-perfor-
mance engines. A lock-up mechanism is built into the torque converter clutch.
The A340E automatic transmission is mainly composed of the torque converter clutch, the overdrive
(hereafter called O/D) planetary gear unit, a 3-speed planetary gear unit, a hydraulic control system
and an electronic control system.
AT0FT-02