1994 MAZDA MX-5 Workshop Manual

TRANSMISSION J Mainshaft Parts Assemble in the order shown in the figure, referring to Assembly Note. WPPLY SPEwim OIL To IwiviDwL PmTs 45UOJX-034 Clutch hub Synchronizer key Clutch hub sleeve Synchronizer key springs Mainshaft 2nd gear Assembly Note .............. page J-32 2nd synchronizer ring Double cone Inner cone Synchronizer assembly (2nd) Clutch hub assembly (Istf2nd) Assembly Note .............. page J-32 3rd gear Assembly Note .............. page J-32 3rd synchronizer ring Clutch hub assembly (3rdl4th) Assembly Note .............. page J-32 Snap ring Assembly Note .............. page J-32 1 st synchronizer ring Bearing race Assembly Note .............. page J-32 Bearing Assembly Note .............. page J-32 1 st gear Assembly Note .............. page J-32 5-31 Gartner Banana

J TRANSMISSION Assembly note Clutch hub assembly 1. Set the 2nd gear, 2nd synchronizer ring, and 1stl2nd clutch hub assembly on the mainshaft, then press in the mainshaft. 2. Set the 3rd gear, 3rd synchronizer ring, and 3rdl4th clutch hub assembly on the mainshaft, then press them onto the mainshaft by using the SST. 3. Install a new snap ring on the front of the mainshaft. 4. Install the bearing race, bearing, and 1 st gear. Gartner Banana

TRANSMISSION J MEMO Gartner Banana

J TRANSMISSION Mainshaft and Countershaft Parts Assemble in the order shown in the figure, referring to Assembly Note. Gartner Banana

TRANSMISSION 1. Clutch hub 2. Synchronizer key 3. Clutch hub sleeve b 4. Synchronizer key springs 5. 4th synchronizer ring 6. Bearing 7. Main drive gear 8. Bearing housing assembly 9. Washer 10. Mainshaft gear assembly Assembly Note .................. below 1 1 . Spacer 12. Countershaft .................. Assembly Note below 13. Counter reverse gear 14. Washer 15. Bearing race 16. Bearing 17. Reverse gear 18. Reverse synchronizer ring 19. Clutch hub assembly (5thlReverse) 20. Locknut (Mainshaft) .................. Assembly Note below 21. 5th synchro-niter ring 22. 5th gear 23. Steel ball 24. Thrust lock washer .............. Assembly Note page J-36 25. C-washer .............. Assembly Note page J-36 26. Retaining ring .............. Assembly Note page J-36 27. Spacer 28. Counter 5th gear 29. Mainshaft rear bearing .............. Assembly Note page J-36 30. C-washer .............. Assembly Note page J-36 31. Retaining ring .............. Assembly Note page J-36 32. Washer .............. Assembly Note page J-36 33. Snap ring 34. Countershaft rear bearing .............. Assembly Note page J-36 35. Locknut (Countershaft) .............. Assembly Note page J-37 45UOJX437 Assembly note Mainshaft and countershaft 1. Place the mainshaft gear assembly and the countershaft on the bearing housing. 2. Use a suitable bar to press in the countershaft. Locknut (Mainshaft) 1. Secure the bearing housing assembly in a vise. 2. Shift the clutch hub sleeves into 1 st and Reverse gears to lock the rotation of the mainshaft. 3. Install a new locknut and tighten it by using the SST. Tightening torque: 128-235 N.m (13-24 kgf.m, 95-173 ftdbf) 4. Use a chisel to stake the locknut. Gartner Banana

J TRANSMISSION Thrust lock washer 1. lnstall the synchronizer ring and 5th gear. 2. Insert the steel ball and thrust lock washer. 3. lnstall only the two 3.0mm I0.118 in) thick C-washers in the front mainshaft groove. 4. Push the C-washers fully toward 5th gear and measure the clearance between the thrust lock washer and C-washers. If the clearance is not as specified, select the proper thrust lock washer. Standard play: 0.1 -4.3mm {O.OO4--O.Ol2 in) Thrust lock washer thickness: 6.2mm (0.244 in), 6.4mm (0.252 in}, 6.5mm (0.256 in), 6.6mm (0.260 in} 5. lnstall the retaining ring. Mainshaft rear bearing 1. lnstall the rnainshaft rear bearing by using the SST, and fully seat it against the front C-washers. 2. lnstall the original C-washers and hold them with the retaining ring. 3. lnstall the washer and new snap ring. u 4. If the C-washers do not fit into the rear mainshaft groove, select the proper thickness C-washers. 5. Verify that both C-washers at one position are the same thickness. 6. With points @ through 0 pressed tightly together, mea- sure the clearance between the washer and snap ring. If the clearance is not as specified, select the proper C- washers. Standard play: 0-0.lmm (0-4.004 in) C-washer thickness: 2.9mm (0.114 in), 3.0mm (0,118 in), 3.1 mm (0.1 22 in), 3.2mm (0.1 26 in) Countershaft rear bearing lnstall the countershaft rear bearing onto the counter- shaft by using the SST. Gartner Banana

TRANSMISSION J & BEARING HOUSING Locknut (Countershaft) 1. Shift the clutch hub sleeves into 1 st and Reverse gears to lock the rotation of the mainshaft. 2. Connect the SST to the mainshaft and secure it in a vise. 3. Install a new locknut and tighten it. Tightening torque: 128-1 96 N.m (13-20 kgf-m, 95--144 ft-lbf) 4. Use a chisel to stake the locknut. Gartner Banana

J TRANSMISSION Shift Fork and Shift Rod Parts Assemble in the order shown in the figure, referring to Assembly Note. 1. Spring and ball 13. Cap plug .............. Assembly Note page J-39 14. Roll pin .............. 2. 5thlReverse shift fork Assembly Note page J-40 .............. Assembly Note page J-39 15. Spring 3. 5thlReverse shift rod Assembly Note .............. page J-40 Assembly Note .............. page J-39 16. Spacer .............. 4. Interlock pin Assembly Note page J-40 .............. Assembly Note page J-39 17. Clip 5. 1 stl2nd shift fork Assembly Note .............. page J-40 Assembly Note .............. page J-40 18. Clip 6. 3rdl4th shift fork Assembly Note .............. page J-40 .............. Assembly Note page J-40 19. Clip .............. 7. Interlock pin Assembly Note page J-40 8. 3rdl4th shift rod 20. Intermediate housing Assembly Note .............. page J-40 Assembly Note .............. page J-41 9. Interlock pin 21. SthlReverse shift rod end Assembly Note .............. page J-40 22. 3rdl4th shift rod end 10. 1 stl2nd shift rod 23. 1 stl2nd shift rod end d 11. Ball and spring 24. Roll pin 12. Washer Assembly Note .............. page J-41 Gartner Banana