1994 MAZDA MX-5 Workshop Manual

T WARNING LIGHT AND SENDER UNIT TROUBLESHOOTING Check the METER 15A fuse in the fuse box before troubleshooting. If it is burnt, replace it after checking and repairing the wiring harness. i/ Brake System Warning Light I Symptom: Brake system warning light remains illuminated. 45UOTX-063 Step 1 - Check brake fluid level Check brake fluid level. Below MIN I I Check brake system (Refer to section P) I Brake fluid level Action Step 2 - Check parking brake switch 1. Disconnect the parking brake switch connector. 2. Check for continuity between the terminal of the switch and ground. Above MIN Go to Step 2 3. If not as specified, adjust or replace the parking brake switch. (Refer to section P.) 4. If the switch is OK, go to Step 3. I Step 3 - Check brake fluid level sensor I 1. Check for continuity of the sensor. *. 1' Lever Pulled one notch Released Continuity Yes No - I Above MIN No Brake fluid level Below MIN 2. If not as specified, replace the level sensor. 3. If the sensor is OK, repair the wiring harness. Continuity Yes Gartner Banana

WARNING LIGHT AND SENDER UNIT T Symptom: Brake system warning light does not illuminate when parking brake is on. (Ignition switch to ON) 45UOTX-065 Remedy 1. Disconnect the parking brake switch connector. 2. Check for continuity between the terminal of the switch and ground. I Released 1 No I Lever 3. If not as specified, adjust or replace the parking brake switch. 4. If the switch is OK, repair the wiring harness. Continuity 010 OFF Indicator Light Symptom: O/D off indicator light does not illuminate when O/D off switch turned on. 45UOTX-069 Pulled one notch I Yes Symptom: Brake system warning light does not illuminate when brake fluid in reservoir tank is below MIN. 45UOTX-067 Remedy 1. Check the bulb of the O/D off indicator light. 2. If the bulb is burned out, replace it. u Remedy 1. Disconnect the brake fluid level sensor connector. 2. Check for continuity of the brake fluid level sensor. Brake fluid level Below MIN Above MIN Continuity Yes No 3. If not as specified, replace the level sensor. 4. If the sensor is OK, repair the wiring harness. Gartner Banana

T WARNING LIGHT AND SENDER UNIT Remedy 1. Disconnect the timer and buzzer unit connector. 2. Turn the ignition switch ON, and verify that the seat belt warning light illuminates. I Warning light illuminates I Action Seat Belt Warning Light The seat belt warning light is controlled by the timer and buzzer unit. 1 Reolace timer and buzzer unit I Symptom: Seat belt warning light remains on six seconds after ignition switch is turned on. (Timer function does not operate.) I Yes Repair wiring harness (Instrument cluster - Timer and buzzer unit) I d 1 Symptom: Seat belt warning light does not illuminate when ignition switch is first turned on. I 45UOTX-070 Step 1 1. Ground terminal J of the timer and buzzer unit connector. 2. Turn the ignition switch ON, and verify that the seat belt warning light illuminates. 1 Warning light illuminates I Action I Step 2 1. Ground terminal D of the timer and buzzer unit connec- tor. 2. Turn the ianition switch ON. and verifv that the seat belt No Yes warning light illuminates. . Go to Step 2 Repair wiring harness (Timer and buzzer unit - GND) Warning light Illuminates Action Replace timer and buzzer unit Check bulb of seat belt warning light If bulb is OK, repair wiring harness (Instrument cluster - Timer and buzzer unit) Gartner Banana

WARNING LIGHT AND SENDER UNIT T OHMMETER Washer Level Indicator lnspection 1. Disconnect the connector from the washer level sensor. 2. Jump terminal-wire L (harness side) to a body ground. 3. Start the engine and check that the WASHER indicator illuminates. 4. If there is no illumination, check the bulb, wiring harness, and sensor. Replace or repair as necessary. Washer Level Sensor lnspection 1. Connect the sensor connector (sensor side) to an ohm- meter. 2. Move the sensor float up and down. 3. Verify that there is continuity when the float is at the low- est point. BRAKE FLUID LEVEL SENSOR lnspection 1. Check for continuity of the sensor. 2. If continuity is not as specified, replace the level sensor. Float level Below MIN Above MIN BUCKLE SWITCt Continuity Yes No OHMMETER -1 PARKING BRAKE SWITCH lnspection 1. Disconnect the parking brake switch connector. 2. Check for continuity between the switch connector and ground. I Lever I Continuity I 3. If continuity is not as specified, adjust or replace the parking brake switch. (Refer to section P.) Pulled one notch Released BUCKLE SWITCH lnspection 1. Disconnect the buckle switch connector 2. Check for continuity of the switch. Yes No Seat belt I Continuity Seat belt buckled Seat belt unbuckled No Yes 3. If continuity is not as specified, replace the buckle switch. Gartner Banana

T LIGHTING SYSTEM LIGHTING SYSTEM STRUCTURAL VIEW 1. Retractable headlight 2. Retractable headlight actuator 3. Stoplight 4. High-mount stoplight 5. Turn and hazard warning light 6. Back-up light 7. License plate light 8. Side marker light 9. Taillight 10. Rear combination light 11. Interior light Gartner Banana

LIGHTING SYSTEM T HEADLIGHTS Circuit Diagram Gartner Banana

T LIGHTING SYSTEM Description The headlight system consists of two halogen headlights mounted on retractable mechanisms, a head- light switch in the combination switch, and a retractor switch between the center ventilation outlets. When the headlight switch is rotated to the second position, the headlights are activated and the retract- able headlight actuator lift the headlights. If only the retractor switch is turned ON, the headlights will raise to the upright position, but all lights will be off. An emergency manual retractor knob is located on top of each retractable headlight actuator. 45UOTX-080 Troubleshooting A retractor indicator light is included in the instrument cluster. The indicator light illuminates when the re- tractable headlight actuator is operating and should go out when the headlights are fully raised or retracted. if the indicator light remains on, small objects, such as pebbles or pieces of ice, may lodged between the headlight and the vehicle body. Use the following procedure to correct this. Turn the ignition switch to OFF. Obtain the code number and deactivate the audio antitheft function. (Refer to page T-120.) Disconnect the negative battery cable or remove the RETRACTOR 30A fuse in the main fuse block. Raise or lower the headlight by turning the emergency retractor knob. Remove the obstruction. After verifying that the headlight switch and the retractor switch are off, reconnect the negative battery cable. Verify operation of the retractable headlight and the retractor indicator light. 45UOTX-095 --- Symptom: Headlights do not illuminate. HEAD 30A MAIN FUSE BLOCK Step 1 1. Check HEAD 30A fuse in the main fuse block. 2. If the fuse is burned, replace it. Check and repair the wir- ing harness, if necessary. 3. If the fuse is OK, go to Step 2. Gartner Banana

LIGHTING SYSTEM T LAY Step 2 1. Turn the headlight switch ON. 2. Measure the voltage at the following terminal-wires of the headlight relay connector. B+: Battery positive voltage Other Action Go to Step 3 Check B terminal Go to Step 6 Check A terminal Check D terminal Repair wirring harness Repair wiring harness (HEAD 30A - Headliclht relav) I Step 3 1. Turn the headlight switch ON. 2. Measure the voltaae at the followinn terminal-wires of - the headlight switch connector. B+: Battery positive voltage Termlnal I Switch position I Voltage / Action I Check I terminal switch) Low beam G B+ Other - Go to Step 4 Replace combination switch High beam Step 4 1. Check the headlight bulbs. 2. If a bulb is burned, replace it. 3. If the bulbs are OK, go to Step 5. B+ Other Go to Step 4 Replace combination switch Gartner Banana