Page 564 of 1708
SHIFT MECHANISM (WITH SHIFT-LOCK SYSTEM) K Removal / Inspection / Installation 1. Disconnect the negative battery cable. 2. Remove in the order shown in the figure, referring to Removal Note. i, 3. Inspect all parts and repair or replace as necessary. 4. Install in the reverse order of removal, referring to Installation Note. 45UOKX-5E 1. Rear console 5. Shift-lock actuator connector 2. Center panel 6. Selector lever 3. Audio unit 4. Spring pin Removal Note ............ page K-164 .......... Installation Note page K-164 Gartner Banana
Page 814 of 1708

DASHBOARD AND CONSOLE DASHBOARD AND CONSOLE COMPONENTS Removal l Installation 1. Disconnect the negative battery cable. Warning Handling the air bag module improperly can accidently deploy the air bag, which may seri- ously injure you. Read SERVICE WARNINGS, section T, before handling the air bag module. 2. Remove in the order shown in the figure, referring to Removal Note. To remove the dashboard, remove the control wires of the heater unit and blower unit. 3. Install in the reverse order of removal. 1. Ashtray 2. Change lever knob 3. Rear console assembly a. Back plate b. Shift lever boot 7. Speedometer cable 8. Instrument cluster 9. Center louver Removal Note ............. page S-57 10. Center an el assemblv c. Power window switch Removal Note ............. page S-58 d. Cover (Without power window) 1 1. Glove box assembly e. Console lock assembly 12. Passenger-side airbag module (if equipped) 4. Center lower panel assembly Removal 1 Installation ......... section T Removal Note ............. page S-57 13. Hood release knob -1 5. Steering shaft 14. Center hole cover 6. Meter hood assembly 15. Side cover Removal Note ............. page $57 16. Dashboard Gartner Banana
Page 815 of 1708
DASHBOARD AND CONSOLE s USA % CLlP CLIP 4 @ CANADA HOOK 0 05UOSX-10 Removal Note Center lower panel assembly The clips are where shown. Meter hood assembly The clips are where shown. Center louver 1. Thread a piece of string through the center louver. 2. Pull the string straight out while holding onto the center panel. Gartner Banana
Page 816 of 1708

DASHBOARD AND CONSOLE - / AIRFLOW MODE WIRE I _ -We -_ -, _ - 11 Center panel assembly The clips are where shown. Adjustment Note Airflow mode wire 1. Set the airflow mode control lever to VENT position. 2. Connect and clamp the wire with the shutter lever on the heater unit at its closest point. 3. Move the airflow mode control lever to make sure the wire is securely attached and that it moves the full stroke from DEF to VENT. REC-FRESH wire 1. Set the selector lever to FRESH position. 2. Connect and clamp the wire with the shutter lever on the blower unit at its closest point. 3. Move the REC-FRESH lever to make sure the wire is securely attached and that it moves the full stroke from - REC to FRESH. TEMF - - I 'ERATURE BLEND WIRE 45UOSX-080 Temperature blend wire 1. Set the temperature blend lever to MAX-HOT position. 2. Connect and clamp the wire with the shutter lever on the heater unit all the way to the right. 3. Move the temperature blend lever to make sure the wire is securely attached and that it moves the full stroke from HOT to COLD. Gartner Banana
Page 1082 of 1708
u HEATER HEATER CONTROL UNIT Removal 1 Installation 1. Remove in the order shown in the figure. 2. Install in the reverse order of removal. 1. Center console 2. Vent outlet 3. Center panel assembly 4. Heater control unit Adjustment . . . . . . . . . . . . . . . . . . page U-22 Gartner Banana