1994 MAZDA MX-5 Workshop Manual

TRIM s TRlM COMPONENTS Removal 1 Installation 1. Remove as shown by prying out the trim clips, referring to Removal Note. 2. Install in the reverse order of removal. Note Remove the brace bar for removal of the quarter trim. (Refer to page S-84.) 1. Front header trim 5. Quarter trim ............. Removal Note ............. page S-60 Removal Note page S-60 2. A-pillar trim 6. Door trim ............. Removal Note ............. page S-60 Removal Note page S-61 3. Front side trim 7. Rear package trim Removal Note ............. page S-60 8. Trunk end trim 4. Scuff plate 9. Trunk side trim Removal Note ............. page S-60 Gartner Banana

TRIM PIN m Removal Note Front header trim The clips and pin are where shown. A-pillar trim The clips and pin are where shown. Front side trim The clip and pins are where shown. Scuff plate The clips and pin are where shown. Quarter trim The clips and pins are where shown. Gartner Banana

TRIM s Door trim The clips and pin are where shown. Gartner Banana

FLOOR COVERING FLOOR COVERING COMPONENTS Removal / Installation 1. To remove the cabin carpet, first remove the following: a Seats (Refer to page S-65.) b Dashboard (Refer to page S-56.) c Heater unit (Refer to Section U) d Front side trim, scuff plates, quarter trim, and rear package trim (Refer to page S-59.) e Front seat belts and buckles (Refer to page S-63.) 2. Remove the remaining parts in the order shown in the figure. 3. Install in the reverse order of removal. 1. Rear end mat 2. Foot rest 3. Bracket 4. Cabin carpet Gartner Banana

SEAT BELT s SEAT BELT COMPONENTS L, Removal 1 Installation Caution The ELR has a spring that will unwind if the retractor's cover is removed. The spring cannot be rewound by hand. If this occurs, the ELR will not work properly. Therefore, do not disas- semble the retractor. 1. Remove the brace bar and the quarter trim. (Refer to page S-59,84) 2. Remove in the order shown in the figure. 3. Install in the reverse order of removal. b 1. Seat belt 3. Bezel Inspection ................. page S-64 4. Buckle switch 2. Anchor cover Inspection ................. page S-64 Gartner Banana

s SEAT BELT SEAT BELT lnspection ELF? 1. Verify that the belt can be pulled out smoothly, and that d it moves smoothly when worn. 2. Verify that the retractor locks when the belt is quickly pulled. 3. Remove the retractor. 4. Hold the retractor as it would be installed. 5. Slowly incline the retractor while pulling out the belt. 6. Verify that the retractor locks at approximately 30 degrees inclination. Webbing Inspect the webbing for scars, tears, and wear and for deformation of the fittings. BUCKLE SWITCH lnspection 1. Disconnect the seat belt buckle switch connector. 2. Check for continuity between the switch terminals. I Unbuckled I Yes I Seat belt Buckled 3. If continuity is not as specified, replace the switch. Continuity No d Gartner Banana

SEAT SEAT COMPONENTS - Removal / Installation 1. Remove in the order shown in the figure. If a headrest speaker is installed, disconnect the speaker con- - nectar to remove the seat. 2. Install in the reverse order of removal. 1. Seat lnspection . . . . . . . . . . . . . . . . . . . . . . below SEAT SEAT lnspection 1. Verify that the seat adjuster lever and reclining knuckle move smoothly. 2. Check the adjustment lever for wear. 3. Check the front seat mounting bolts for looseness. 4. Check grease on the seat slides. Gartner Banana

SEAT Disassembly 1 Assembly 1. Disassemble in the order shown in the figure. (Refer to Section T for disassembly / assembly of the body sonic seat.) 2. Assemble h the reverse order of disassembly. 1. Reclining knuckle cover 2. Side cover 3. Reclining knuckle 4. Hinge cover 5. Bush 6. Belt anchor unit 7. Hog ring 8. Seatback trim 9. Pad 10. Back frame 11. Headrest speaker (if equipped) Inspection . . . . . . . . . . . . . . . . . . . Section T 12. Seat slide 13. Seat cushion Gartner Banana