2013 SSANGYONG TURISMO Service Manual

01-20
▶F31 ~ F36

02-38710-01
1. SPECIFICATIONS OF RK - STICS
1) Electrical Performance
2) Chattering of Input Signals
Vehicle speed input:
The vehicle speed calculating time is 1.0 seconds. The elapsed time of 1.5 seconds after IGN
1 switch :ON” is not included.
20 ms target input:
Wiper motor A/S (parking) terminal
100 ms target input switch
All switches except wiper motor A/S (parking) terminal 1.
2.
3.
3) Time Tolerance
If not indicated, time tolerance will be ± 10%.
However, if less than 500 ms, time tolerance will be ± 50 ms.
The time indicated in each function does not include chattering processing time from switch
input changing point. 1.
2.
Item Requirement Remark
Rated voltage DC 12 V
Operating voltage DC 9 to 16 V Should operate normally within this range.
Operating temperature-30℃ ~ +80℃
Reserved temperature-40℃ ~ +85℃
Max. operating humidity 95%
Resistible voltage 24 V
Insulating resistance No heat and fire due to
the current leaks.Confined with PCB, waterproof and coating that
requires the insulation.
Parasitic current below 4.0 mA
(below 6.0 mA)IGN = OFF, Full output load = OFF, 90
seconds (after received the signals), No input
changes for 2 seconds
Voltage drop below 1.2 V
below 2.0 VPin no. 8 and 2, 3, 5, 7, 10, 12, 13, 15, 19, 20,
23, 40, 47, 51, 53, 54
Pin no. 8 and 1, 14

02-4
4) Input Signals Of Rk Stics

02-58710-01
The remote engine control function has been deleted in this model.
1. COMPONENTS
STICS / ICM module
Air bag ECU
Sends the vehicle collision
signals to STICS.
Theft deterrent horn
Installed under the battery.
This horn works only for the
theft deterrent function, panic
function, and remote starting.
SCAN-tool
SIW is used for REKES key
coding and trouble
diagnosis.
REKES
Added the escort and panic
function
RK STICS
ICM module
This module contains
various relays, chime and
buzzer controlled by STICS

02-6
2. FUNCTIONS OF RK STICS
1) Wiper Control
(1) Wiper MIST and Washer Coupled Wiper
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch for 0.2 ~
0.59 seconds (T2) with the ignition key “ON”, and it is turned off when the parking terminal
is turned off. 1.
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch over 0.6
seconds (T2) with the ignition key “ON”, and it is turned on three times immediately after
turning off the washer switch. 2.

02-78710-01
If the washer operating signal is inputted while the wipers are operating in intermittent or AUTO
mode, the system stores the previous intermittent interval and operates the washer coupled wiper.
After then, the wiper operation returns back to intermittent or AUTO mode with the stored operating
interval. 3.

02-8
(2) Rain Sensor Coupled Wiper
▶ System layout
This vehicle has a different wiper control logic compared to other models. As shown in the system
diagram, the rain sensor unit does not control wiper directly. The rain sensor unit sends infrared rays
signal through LED and then receives it with photo diode and then sends the returned signal to STICS
and the STICS controls the wipers directly.
For more details, refer to rain sensing wiper section in this manual.

02-98710-01
▶ Rain sensing operation point
The wiper relay is turned on and the wiper motor runs one cycle when the ignition key is turned to
“ON” position (while the wiper switch is in “AUTO” position).
The wiper relay (LO) is turned on and the wiper motor runs one cycle when changing the wiper
switch to “AUTO” position from any other positions (while the ignition key is in “ON”
position). When the wiper switch is turned to “AUTO” position again from other positions,
the system drives the wiper relay (LO) to run the wiper motor one cycle only when the rain sensor
detects the “Rain Detected” signal. 1)
2)