2022 TOYOTA GR86 Owners Manual (in English)

35
3
3-2. Other settings
Settings
12 Select “Download Now” to begin
downloading the update (if avail-
able).
 “Cancel”: Select to stop the
update process.
 The download status progress is
displayed in the category area.
 If the update procedure fails,
refer to the “Troubleshooting”
section. ( P. 9 6 )
1 Download any available
updates.
2 Select “Install Now” to start
installing the update.
 Installation will take several min-
utes.
●During software update installation, the screen may flicker. However, this
is not a malfunction.
3 When installation is complete,
select “OK” on the confirmation
message to complete the
update process.
 If the update procedure fails,
refer to the “Troubleshooting”
section. ( P. 9 6 )
4 Turn the engine switch to Off.
5 Open the driver’s side door.
6 Close the door.
7 Wait for 3 minutes or more.
8 Start the engine.
 The new software will be applied.
Update installation
NOTICE
●Park your vehicle in a safe place
when installing the update.
●The following system functions are
restricted during the update installa-
tion.
• It will not be possible to use general
system functions.
• Only the rear view camera image
will be displayed. Or the image will
disappear temporarily.

363-2. Other settings
1Press the button.
2 Select “Settings”.
3 Select “Sound”.
4 Select the items to be set.
Select to audio settings
“Sound Customisation”: Select to dis-
play the sound customisation screen.
( P. 6 5 )
“Sound Restorer”: Select to turn the
sound restorer function on/off.
This function plays compressed audio
with quality near original sound by add-
ing the complement signal of high tone.
“Virtual Bass”: Select to set the virtual
bass function.
This function corrects the bass sound
by adding harmonic sound.
“Dynamic Beat Enhancer”: Select to set
the dynamic beat enhancer function.
This function expands the dynamic
range lost in data compression and cre-
ates a sharp beat sound.
“Speed Volume Control”: Select to set
the speed volume.
The system adjusts to the optimum vol-
ume and tone quality according to vehi-
cle speed to compensate for increased
vehicle noise.
“AUX Volume Gain”: Select to set AUX
volume gain.
Select to adjust the interrupt
guidance volume.
Select to turn the tone sound
on/off.
Select to adjust the tone sound
volume.
Select to adjust the ringtone vol-
ume.
Select to adjust the volume of a
received call.
Select to adjust the call volume.
Select to adjust the SMS/MMS
ringtone volume.
Select to adjust the SMS/MMS
read out volume.
Select to set the voice recogni-
tion prompts volume.
Sound settings
Sound settings screen
A
B
C
D
E
F
G
H
I
J

37
3
3-2. Other settings
Settings
1 Press the button.
2 Select “Settings”.
3 Select “Radio”.
1 Display the radio settings
screen. ( P. 3 7 )
2 Select “FM/AM”.
3 Select the desired item to be
set.
Select to turn the news
announcement on/off.
Select to turn the TA (traffic
announcement) on/off.
Select to turn the AF (alternative
frequency) on/off.
Select to turn the REG (region-
alisation) on/off.
For switching over to a broad-
casting station within the same
local programme network.
This item can be set when
“Alternative Frequency” is
turned on.
Select to set the interrupt vol-
ume.
Select to set seek sensitivity as
“DX (Distance)” or “LO (Local)”.
*: If equipped
1 Display the radio settings
screen. ( P. 3 7 )
2 Select “DAB”.
3 Select the desired item to be
set.
Radio settings
Radio settings screen
Setting AM/FM radio
A
B
C
Setting the DAB*
D
E
F

383-2. Other settings
Select to turn DAB to DAB Link-
ing on/off.
When set to on, if the reception
quality of the current DAB sta-
tion decreases and the station is
not simulcasting on FM, a DAB
station with an identical Service
ID will be searched for and
changed to if it has better recep-
tion quality.
Select to turn DAB to FM Link-
ing on/off.
When set to on, if the reception
quality of the current DAB sta-
tion decreases to a certain
threshold level, the system will
automatically switch to a simul-
cast FM broadcast, if available.
“FM” appears on the screen if
an FM station is received.
Select to turn the TA (traffic
announcement) interrupt feature
on/off.
Select to turn the dynamic range
control feature on/off.
Select to turn the information
button on/off on the DAB
screen.
Select to set the tuning method
as “Seek” or “Manual Tune”.
1 Press the button.
2 Select “Maintenance”.
 Maintenance reminders can be
set.
1 Select (“Engine Oil”).
2 Select “Notification Date” or
“Notification Distance (Remain-
ing)” of the reminder.
3 After entering the notification
date or notification distance,
select “Set”.
4 Select .
A
B
C
D
E
F
Maintenance settings
When approaching the set
maintenance reminder notifica-
tion date or notification dis-
tance, a message will be
displayed when the engine
switch is changed to ON. This
function can be set to on or off
by “Reminder Screen”. ( P. 2 9 )
Maintenance settings
screen
Engine oil setting

39
3
3-2. Other settings
Settings
The setting procedure is the same
as Engine oil setting, but select the
“Oil Filter” item in step 1.
The setting procedure is the same
as Engine oil setting, but select the
“Tyres” item in step 1.
The setting procedure is the same
as Engine oil setting, but select the
“Maintenance Schedule” item in
step 1.
●Select “Reset” to reset each setting.
●Select “Update” to revert to the default
value.
Oil Filter setting
Tyres setting
Maintenance Schedule set-
ting

403-2. Other settings

4
41
4
Phone
Phone
.4-1. Phone operation (Hands-free
system for mobile phones)
Phone screen ..................... 42
Some basics ....................... 43
Calling on the Bluetooth®
phone ............................... 46
Receiving on the Bluetooth®
phone ............................... 48
Talking on the Bluetooth®
phone ............................... 49
Bluetooth® phone message
function ............................. 50

424-1. Phone operation (Hands-free system for mobile phones)
4-1.Phone operation (Hands-free system for mobile phones)
The phone screen can be accessed
with the following methods:
 Press the button, and then
select “Phone”.
 Press the button.
The following functions can be
used on phone operation:
 Registering a Bluetooth®
phone/device: P. 1 9
 Calling on the Bluetooth® phone:
 P. 4 6
 Receiving on the Bluetooth®
phone: P. 4 8
 Talking on the Bluetooth® phone:
 P. 4 9
The following function can be used
on message function:
 Using the Bluetooth® phone
message function: P. 5 0
The following function can be made
in the system:
 Setting the Bluetooth®
phone/device: P. 2 4
Phone screen
Phone screen operation
Phone operation
Message function
Setting up a phone