2464-6. Using other driving systems
Range of view
Image from camera
The area above the camera cannot
be viewed. If there is an object that
has a wide projection on its upper
part such as a sign pole behind the
vehicle, the projection cannot be
seen on the screen.
Range of view
Image from camera
The help lines are a guide to help
you realize the actual distance from
the screen image.
Help lines
Vehicle width line (oblique verti-
cal line)
Approx. 3 m (10 ft) from the
bumper (green horizontal line)
Approx. 2 m (6 ft) from the
bumper (green horizontal line)
WA R N I N G
The range that can be viewed with the
rear view camera is limited. Always be sure to check with your eyes when
moving backward and proceed slowly.
Otherwise, it may cause an accident
or injury.
Help lines
A
C
313
6
6-3. Do-it-yourself maintenance
Maintenance and care
When replacing wheels, care
should be taken to ensure that they
are equivalent to those removed in
load capacity, diameter, rim width
and inset*.
Replacement wheels are available
at any authorized Toyota retailer or
Toyota authorized repairer, or any
reliable repairer.
*: Conventionally referred to as offset.
Toyota does not recommend using
the following:
Wheels of different sizes or types
Used wheels
Bent wheels that have been
straightened
■When replacing wheels
The wheels of your vehicle are equipped with tire pressure warning valves and
transmitters that allow the tire pressure
warning system to provide advance warning in the event of a loss in tire
inflation pressure. Whenever wheels are
replaced, tire pressure warning valves and transmitters mu st be installed.
( P.304)
Wheels
If a wheel is bent, cracked or
heavily corroded, it should be
replaced. Otherwise, the tire
may separate from the wheel
or cause a loss of handling
control.
Wheel selection
WA R N I N G
■When replacing wheels
●Do not use wheels that are a differ-
ent size from those recommended in the Owner’s Manual, as this may
result in a loss of handling control.
●Never use an inner tube in a leak-
ing wheel which is designed for a
tubeless tire. Doing so may result in
an accident, causing death or seri- ous injury.
■When installing the wheel nuts
Never use oil or grease on the wheel
bolts or wheel nuts. Oil and grease
may cause the wheel nuts to be excessively tightened, leading to bolt
or disc wheel damage. In addition, the
oil or grease can cause the wheel nuts to loosen and the wheel may fall
off, causing an accident and resulting
in death or serious injury. Remove any oil or grease from the wheel bolts
or wheel nuts.
■Use of defective wheels prohib-
ited
Do not use cracked or deformed wheels. Doing so could cause the tire
to leak air during driving, possibly
causing an accident.
NOTICE
■Replacing tire pressure warning
valves and transmitters
●Because tire repair or replacement may affect the tire pressure warning
valves and transmitters, make sure
to have tires serviced by any authorized Toyota retailer or Toyota
authorized repairer, or any reliable
repairer or other qualified service shop. In addition, make sure to pur-
chase your tire pressure warning
valves and transmitters at any authorized Toyota retailer or Toyota
authorized repairer, or any reliable
repairer.
3688-1. Specifications
8-1.Specifications
*: Unladen vehicle
■Vehicle identification number
The vehicle identification number
(VIN) is the legal identifier for your
vehicle. This is the primary identifi-
cation number for your Toyota. It is
used in registering the ownership of
your vehicle.
This number is stamped under the
right-hand front seat. This number is located on the top
left of the body panel.
Maintenance data (fuel, oil level, etc.)
Dimensions and weights
Overall length4265 mm (167.9 in.)
Overall width1775 mm (69.9 in.)
Overall height*1310 mm (51.6 in.)
Wheelbase2575 mm (101.4 in.)
TreadFront1520 mm (59.8 in.)
Rear1550 mm (61.0 in.)
Gross vehicle mass
Details are described on the tire
and loading information label.
( P.368)
Maximum permissible axle
capacity
Front876 kg (1931 lb.)
Rear943 kg (2079 lb.)
Vehicle identification
726-3. Media operation
6-3.Media operation
The USB Audio/Video playback
screen can be accessed with the
following methods:
Connect a USB memory device.
( P. 1 9 )
Select “USB” on the media con-
trol screen. ( P.64)
Audio
Video
Select to switch between other
media sources.*
Displays cover art.
Select to display the sound cus-
tomisation screen. ( P. 6 5 )*
Shows progress.
The playback location can be
changed by dragging the slid-
ers.
Select to search for a track/file.*
Changes between repeat cur-
rent album/folder repeat cur-
rent track/file cancel repeat
each time this button is
selected.*
Select to enable/disable random
playback for the tracks currently
playing from the USB memory
device.
Select to pause/play.*
Select to change the track/file.
Select and hold to fast for-
ward/rewind.*
Select to change the video set-
tings.*
“Screen Size Change”: Select to adjust
the screen size.
Select “Full Wide” to enlarge the image
horizontally to fill the screen.
Select “Original” to display the image
with its native width.
“Play State Indication”: Select to display
detailed information about the currently
playing video.
Select to stop the video screen.*
USB memor y
Audio files and video files on a
USB memory device can be
played back/viewed. While
driving, video will not be dis-
played. Only sound will be out-
put.
Overview
Control screen
A
B
C
D
E
F
G
H
I
J
K
