2009 LAMBORGHINI GALLARDO Workshop Manual


L714 08 45 05
)LJ
C
)LJ
)LJ
'
)LJ
(
%
A
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
%$VVHPEOLQJWKHUHDUZLQGRZ • Wear cotton gloves (to avoid direct contact with the rear window’s surface).
1. Clean the surface of the body where the rear window will be glued using a cloth and VITREX.
2. Protect the body near the rear window’s housing with tape.
 Clean the surface of the rear window where it will be glued using a cloth and VITREX.
4. Apply the BETAPRIME primer with the yellow cap ( &)LJ) along the internal edge of the rear window ( A-
)LJ ) using the special pad ( %)LJ).
The pad must be thrown away after use. The pad may not be used to apply different types of
products.
5. Apply the BETAPRIME primer with the green cap ( ')LJ) along the internal edge of the rear window ( A-
)LJ ) (where the BETAPRIME with the yellow cap was applied) using the special pad ( %)LJ).
The pad must be thrown away after use. The pad may not be used to apply different types of
products.
 Apply the BETAPRIME primer with the red cap ( ()LJ) along the edge of the body where the rear window
will be applied using the special pad.

7
L714 08 45 05
)LJ
H
)LJ)LJ )LJ
G
G
)
)
L
M
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
7. Using double-sided tape, attach the 6 shims to the inside of the window:
• 4 at the corners ( ))LJ)
• 2 at the midpoint at the top and bottom ( *)LJ)
8. Distribute the BETASEAL 1965 silicone ( +)LJ) along the internal edge of the rear window using the provided
spout ( /)LJ ) preformed by means of the special pliers ( 0)LJ) with an opening 10 mm high and 5 mm
wide.

8
L714 08 45 05
)LJ
1
O
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
 Position the rear window ( 1)LJ), taking care that the silicone does not internally extend beyond the edge.
10. After the window has been centered, press down on the edges so that the silicone adheres well.
11. Secure the rear window onto the car using the cloth tape ( 2)LJ).


L714 08 45 05
)LJ
A
)LJ
%
)LJ
(
)LJ
C
''
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
C) Assembling the front side window • Wear cotton gloves (to avoid direct contact with the front side window’s surface).
1. Clean the surface of the body where the front side window will be glued using a cloth and VITREX.
2. Protect the body near the front side window’s housing with tape.
 Clean the surface of the front side window where it will be glued using a cloth and VITREX.
4. Apply the BETAPRIME primer with the yellow cap ( $)LJ) along the internal edge of the front side window
using the special pad.
The pad must be thrown away after use. The pad may not be used to apply different types of
products.
5. Apply the BETAPRIME primer with the green cap ( %)LJ) along the internal edge of the front side window
(where the BETAPRIME with the yellow cap was applied) using the special pad.
The pad must be thrown away after use. The pad may not be used to apply different types of
products.
 Secure the 2 housings ( &)LJ) for coupling the duct with the body using the rivets ( ')LJ) (2 rivets per
housing).
7. Apply the BETAPRIME primer with the red cap ( ()LJ) along the edge of the body where the front side
window will be applied using the special pad.

10
L714 08 45 05
)LJ
G
)LJ
H
L
)LJ
)
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
8. Distribute the BETASEAL 1965 silicone ( *)LJ) along the internal edge of the front side window ( ))LJ)
using the provided spout ( +)LJ) preformed by means of the special pliers ( /)LJ) with an opening 10 mm
high and 5 mm wide.

11
L714 08 45 05
)LJ )LJ
M
1
O
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
 Position the front side window ( 0)LJ) inside the previously assembled housings, taking care that the silicone
does not internally extend beyond the edge.
10. Assemble the duct ( 1)LJ) inside the housings positioned at the top of the body of the side window.
11. After verifying the front side window’s correct position, hold it in place on the car using the special cloth tape
(2)LJ ).

12
L714 08 45 05
)LJ
A
)LJ
%
)LJ
(
)LJ
C
''
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
'$VVHPEOLQJWKHUHDUVLGHZLQGRZ • Wear cotton gloves (to avoid direct contact with the rear side window’s surface).
1. Clean the surface of the body where the rear side window will be glued using a cloth and VITREX.
2. Protect the body near the rear side window’s housing with tape.
 Clean the surface of the rear side window where it will be glued using a cloth and VITREX.
4. Apply the BETAPRIME primer with the yellow cap ( $)LJ) along the internal edge of the rear side window
using the special pad.
The pad must be thrown away after use. The pad may not be used to apply different types of
products.
5. Apply the BETAPRIME primer with the green cap ( %)LJ) along the internal edge of the rear side window
(where the BETAPRIME with the yellow cap was applied) using the special pad.
The pad must be thrown away after use. The pad may not be used to apply different types of
products.
 Secure the 4 housings ( &)LJ) for coupling the duct with the body using the rivets ( ')LJ) (2 rivets per
housing).
7. Apply the BETAPRIME primer with the red cap ( ()LJ) along the edge of the body where the rear side
window will be applied using the special pad.


L714 08 45 05
)LJ
G
)LJ
H
L
)LJ
)
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
8. Distribute the BETASEAL 1965 silicone ( *)LJ) along the internal edge of the rear side window ( ))LJ)
using the provided spout ( +)LJ) preformed by means of the special pliers ( /)LJ) with an opening 10 mm
high and 5 mm wide.