2006 MERCEDES-BENZ ML500 Owner's Manual

168 Controls in detailControl system
Pressæ orç to select
Manual
or
daytime running lamp (
Constant
)
mode.
With daytime running lamp mode se-
lected and the exterior lamp switch at
positionM, the following lamps will
come on automatically when the en-
gine is turned on:


Parking lamps and low beam
headlamps


License plate lamps (in low ambient
light conditions)Setting locator lighting
With the locator lighting feature activated
and the exterior lamp switch in
position
U
, the following lamps will
switch on during darkness when the vehi-
cle is unlocked with SmartKey:


Parking lamps


Tail lamps


License plate lamps


Side marker lamps


Front fog lamps
The locator lighting switches off when the
driver’s door is opened. It switches off au-
tomatically after a period of approximately
40 seconds.
iIf you turn the exterior lamp switch to
another position, the corresponding
lamp(s) will switch on.
For safety reasons, resetting the Lighting
submenu to factory settings
while driving will not reset the daytime
running lamp mode.
In the display you will then see the mes-
sage:
Lighting - Cannot be com-
pletely reset to factory settings
while driving.


169 Controls in detail
Control system

Move the selection marker to the Lighting
submenu using theæ
orç button.

Press buttonj ork repeatedly
until you see this message in the dis-
play:
Function Surround lighting
.
The selection marker is on the current
setting.

Press buttonæ orç to select
the desired setting.
The locator lighting will be switched on
or off.

Turn the exterior lamp switch to
positionU when exiting the vehicle
(page 138).Setting night security illumination
(Headlamps delayed shut-off)
Use this function to set whether and how
long you would like the exterior lamps to
illuminate during darkness after exiting the
vehicle and all doors closed.
With the delayed shut-off feature activated
and the exterior lamp switch in
position
U
before the engine is turned
off, the following lamps will switch on
when the engine is turned off:


Parking lamps


Tail lamps


License plate lamps


Side marker lamps


Front fog lamps

Move the selection marker to the Lighting
submenu using theæ
orç button.

Press buttonj ork repeatedly
until you see this message in the dis-
play:
Headlmp. delayed shut-off
.
The selection marker is on the current
setting.
iYou can reactivate this function within
ten minutes by opening a door.
If after turning off the engine you do not
open a door or do not close an opened
door, the lamps will automatically
switch off after 60 seconds.


170 Controls in detailControl system
Press buttonæ orç to select
the desired lamp-on period.
You can select:

0 s
, the delayed shut-off feature is
deactivated.


15 s
, 30 s
, 45 s
or
60 s
, the delayed
shut-off feature is activated.

Turn the exterior lamp switch to posi-
tion U before turning the engine off.
You can temporarily deactivate the de-
layed shut-off feature:

Before leaving the vehicle, turn the
SmartKey in the starter switch to
position0.

Then turn the SmartKey in the starter
switch to position2 and back to0.
The delayed shut-off feature is deacti-
vated. It will reactivate as soon as you
reinsert the SmartKey in the starter
switch.Vehicles with KEYLESS-GO*:

Press KEYLESS-GO start/stop button
in the starter switch (
page 35).
Interior lighting delayed shut-off
Use this function to set whether and for
how long you would like the interior light-
ing to remain lit during darkness after the
SmartKey is removed from the starter
switch.

Move the selection marker to the Lighting
submenu using theæ
orç button.

Press buttonj ork repeatedly
until you see this message in the dis-
play:
Int. illum. delayed shut-off
.
The selection marker is on the current
setting.

Press buttonæ orç to select
the desired lamp-on time period. You
can select:

0 s
, the delayed shut-off feature is
deactivated.


5 s
, 10 s
, 15 s
, or
20 s
, the delayed
shut-off feature is activated.


171 Controls in detail
Control system
Vehicle submenu
Access the
Vehicle
submenu via the
Settings...
menu. Use the
Vehicle
sub-
menu to make general vehicle settings.
The following functions are available:Adjusting compass zone
This function is not available if your vehicle
is equipped with the Modular COMAND
System and navigation module*.
Use this function to set the compass zone.
To set the compass zone:

Move the selection marker to the Vehicle
submenu using theæ
orç button.

Press buttonj ork repeatedly
until you see this message in the dis-
play:
Compass Adjustment Zone
.
The selection marker is on the current
setting.

Press buttonæ orç to set the
respective compass zone.For information on how to select the prop-
er geographic zone, see “Compass”
(
page 295).
Calibrating compass
This function is not available if your vehicle
is equipped with the Modular COMAND
System and navigation module*.
Use this function to calibrate the compass
zone.
To calibrate the compass:

Move the selection marker to the Vehicle
submenu using theæ
orç button.

Press buttonj ork repeatedly
until you see this message in the dis-
play:
Compass Calibration
.
The selection marker is on the current
setting.
Function
Page
Adjusting compass zone
171
Calibrating compass
171
Display when ignition is
switched off
172
Set automatic locking
172
Limiting opening height of tail-
gate*
173


172 Controls in detailControl system
Press buttonæ to start calibrating
the compass.
Display when ignition is switched off
Use this function to select which message
will be shown in the multifunction display
when the ignition is being switched off.

Move the selection marker to the Vehicle
submenu using theæ
orç button.

Press buttonj ork repeatedly
until you see this message in the dis-
play:
Display when ignition is
turned off
.
The selection marker is on the current
setting.

Press buttonæ orç to select
the desired setting.Setting automatic locking
Use this function to activate or deactivate
the automatic central locking. With the au-
tomatic central locking system activated,
the vehicle is centrally locked at vehicle
speeds of approximately 9 mph
(15 km/h).

Move the selection marker to the Vehicle
submenu using theæ
orç button.

Press buttonj ork repeatedly
until you see this message in the dis-
play:
Automatic door lock
.
The selection marker is on the current
setting.

Press buttonæ orç to switch Automatic door lock
On or
Off
.


173 Controls in detail
Control system
Limiting opening height of tailgate*
Use this function to activate or deactivate
the limiting opening height of tailgate.
Move the selection marker to the Vehicle
submenu using theæ
orç button.

Press buttonj ork repeatedly
until you see this message in the dis-
play:
Opening limiter Tailgate
.
The selection marker is on the current
setting.

Press buttonæ orç to switch Opening limiter Tailgate On
or
Off
.Convenience submenu
Access the
Convenience
submenu via the
Settings...
menu. Use the
Convenience

submenu to change the settings for a num-
ber of convenience features. The following
functions are available:
Activating easy-entry/exit feature*
Use this function to activate and deacti-
vate the easy-entry/exit feature
(
page 128).Function
Page
Activating easy-entry/exit
feature*
173
Set parking position* for exteri-
or rear view mirror
174
Setting fold-in function* for
exterior rear view mirrors
175
Warning!
G
You must make sure no one can become
trapped or injured by the moving steering
wheel and driver’s seat when the
easy-entry/exit feature is activated.
To stop seat/steering wheel movement, do
one of the following:

Press seat adjustment switch
(page 39).


Move steering column stalk*
(page 42).


Press one of the memory position but-
tons or the memory button
M*
(
page 136).
Do not leave children unattended in the
vehicle, or with access to an unlocked
vehicle. Children could open the driver’s
door and unintentionally activate the
easy-entry/exit feature, which could re-
sult in an accident and/or serious per-
sonal injury.

174 Controls in detailControl system
Move the selection marker with
theæ orç button to the

Convenience
submenu.

Press buttonj ork repeatedly
until you see this message in the multi-
function display:
Func. Easy-entry
feature
.
The selection marker is on the current
setting.

Press buttonæ orç to change
the easy-entry/exit setting.The following settings are available for the
easy-entry/exit feature:Setting parking position* for exterior
rear view mirror
Use the
Mirror adjustment parking aid

function to select whether the passen-
ger-side exterior rear view mirror should be
turned downward during parking maneu-
vers when reverse gearR is engaged. For
additional information, see “Activating ex-
terior rear view mirror parking position*”
(
page 196).

Move the selection marker to the

Convenience
submenu using theæ
or çbutton.

Press buttonj ork repeatedly
until you see this message in the dis-
play:
Mirror adjustment parking
assist.
The selection marker is on the current
setting.
Off
The easy-entry/exit
feature is deactivat-
ed.
Steering col.
Only the steering col-
umn is moved.
Steer. col.+seat
Both the steering
column and the driv-
er’s seat are moved.

175 Controls in detail
Control system

Press buttonæ orç to switch
function
On or
Off
.
Setting fold-in function* for exterior
rear view mirrors
Using this function, you can set the exteri-
or rear view mirrors to be automatically
folded (
page 197) in when you lock your
vehicle.

Move the selection marker with
theæ orç button to the

Convenience
submenu.

Press buttonj ork repeatedly
until you see this message
Fold in
mirrors when locking
appears in the
display.
The selection marker is on the current
setting.

Press buttonæ orç to switch
function
On or
Off
.
Vehicle configuration
The following functions are available:
Parktronic system* on/off
Switch on the ignition (
page 34).

Pressè orÿ button repeatedly
until the
Vehicle configuration
menu
appears in the display.

Pressj ork repeatedly until
the message
PARKTRONIC
appears in
the display.
Function
Page
Parktronic* on/off
175
DSR set speed
176
Tow-away alarm on/off
176