2006 LAND ROVER FRELANDER 2 tires

Publi s hed: 11-May-2011
Wheels and Tires - Tire Pressure Monitoring System (TPMS) Front Antenna
Removal and Inst all ati on
Removal
1. W ARNING: Do not work on or under a vehi cle s upported onl yby a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he front wheel .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal andInst all at ion).
2.
Remove t he fender spl as h shi el d extens ion panel.3.
Releas e t he front of t he fender s plas h s hi eld.4.
Remove t he ti re pres sure antenna.5.

Publi s hed: 11-May-2011
Wheels and Tires - Tire Pressure Monitoring System (TPMS) Rear Antenna
Removal and Inst all ati on
Removal
1. W ARNING: Do not work on or under a vehi cle s upported onl yby a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
1.
Releas e t he fender spl as h shi el d.2.
Remove t he ti re pres sure antenna.3.
Installation
To i nst all , revers e t he removal procedure.1.
Init iate a new t ire pres s ure ant enna us i ng W DS.2.

Publi s hed: 11-May-2011
Vehicle Dynamic Suspension - Rear Suspension Height Sensor
Removal and Inst all ati on
Removal
• NOTE: This s ens or i s only fit ted to vehicles wit h Xenon headlamps and is i nst all ed on the LH s ide of t he vehi cl e.
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he wheel and t ire.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2. T orque:
10 Nm 3.
4.

Publi s hed: 11-May-2011
Rear Drive Axle/Differential - Differential Case
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he LH rear wheel and ti re.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal andInst all at ion).
2.
W it h ass i st ance, remove the rear muffler.
Refer t o: Exhaus t Sys t em (309-00A Exhaus t Sys t em - I6 3.2L Pet rol ,Removal and Ins tall ati on).
3.
4. W ARNING: Do not lever the driveshaft joint s t orel ease from t he power trans fer unit or t he reardifferent ial flanges .
• CAUTIONS:
Mark t he components to ai d ins t al lat ion.
Make s ure that t he dri ves haft i s s upport ed wi ths uit abl e ret aini ng st raps .
Di scard the bolt s .
4.
5.

Inst all t he rear different ial rear bus h ret aining bol ts .
T orque: 110 Nm Inst all t he LH halfshaft.
Refer t o: Rear Hal fs haft LH (205-05 Rear Dri ve Halfs haft s , Removal
and Inst all at ion).
9.
Connect t he Act ive On-demand Coupl ing modul e electrical connect or.
10.
Inst all t he dri ves haft rear s upport bracket .
T orque: 35 Nm 11.
12. CAUTION: Make s ure t hat new bol ts are
ins tal led.
Connect the drives haft t o the rear fl ange.
T orque: 40 Nm 12.
Inst all t he rear muffler.
Refer t o: Exhaus t Sys t em (309-00A Exhaus t Sys t em - I6 3.2L Pet rol ,
Removal and Ins tall ati on).
13.
Inst all t he LH rear wheel and ti re.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
14.
Check and top-up the acti ve on-demand coupl ing fluid level.
Refer t o: Act ive On-Demand Coupl ing Fi lli ng (205-02 Rear Drive
Axle/Different ial, General Procedures).
15.
Fil l the di fferenti al cas e wit h flui d.
Refer t o: Different ial Drai ni ng and Fil ling (205-02 Rear Drive
Axle/Different ial, General Procedures).
16.

Removal
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove both rear wheel s and t ires .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2.
Remove t he rear different ial.
Refer t o: Different ial Case (205-02 Rear Drive Axle/Different ial,
Removal and Ins tall ati on).
3. 4.
CAUTIONS: Mark t he components to ai d ins t al lat ion.
Not e t he fi tt ed pos it ion of t he component prior t o
removal .
Us ing t he s peci al t ools , remove t he bus hi ng.
Speci al Tool (s ): 205-860-01 ,
205-860-02 ,
205-860-10 ,
LR-121 4.
Installation Us ing t he s peci al t ool, compres s t he bus hing.
Speci al Tool (s ): 205-860-09 ,
205-860-04 ,
LR-121 1.
2. CAUTION: Make s ure the correct s peci al tool is
us ed to ins tal l the bus hings to the correct dept h.
• NOTE: Make s ure that t hes e component s are ins tal led
t o t he not ed removal pos it ion.
Us ing t he s peci al t ool, i ns t all the bus hing.
Speci al Tool (s ): 205-860-10 ,
205-860-01 ,
205-860-04 ,
205-860-03 ,
LR-121 2.
Inst all t he rear different ial.
Refer t o: Different ial Case (205-02 Rear Drive Axle/Different ial,
Removal and Ins tall ati on).
3.
Inst all t he rear wheels and t ires.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
4.

Removal
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove both rear wheel s and t ires .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2.
Remove t he rear different ial.
Refer t o: Different ial Case (205-02 Rear Drive Axle/Different ial,
Removal and Ins tall ati on).
3. Take note of t he fit ted pos it ion of t he rear bushi ngs .
The RH bus hing s l ot i s pos it ioned verti cal ly and t he LH
bus hi ng s lot is pos i ti oned horizont all y.
4. 5. CAUTION: Not e the fi tt ed posi ti on of the
component pri or to removal.
Us ing t he s peci al t ool, remove the bus hing.
Speci al Tool (s ): 205-861-01 ,
205-861-02 ,
LR-121 5.
Installation

1. CAUTION: Only use the s peci fi ed s pecial t ool .
Us ing t he s peci al t ool, compres s t he bus hing.
Speci al Tool (s ): 205-860-09 ,
205-861-05 ,
LR-121 1.
2. CAUTION: Make s ure the correct s peci al tool is
us ed to ins tal l the bus hings to the correct dept h.
• NOTE: Make s ure that t hes e component s are ins tal led
t o t he not ed removal pos it ion.
Us ing t he s peci al t ool, i ns t all the bus hing, making s ure
t he s lot on t he RH bus hing i s pos i ti oned verti call y and
t he s lot on t he LH bus hi ng is pos it ioned hori zont all y.
Speci al Tool (s ): LR-121 ,
205-861-04 ,
205-861-03 ,
205-861-05 2.
Inst all t he rear different ial.
Refer t o: Different ial Case (205-02 Rear Drive Axle/Different ial,
Removal and Ins tall ati on).
3.
Inst all t he rear wheels and t ires.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
4.