2006 LAND ROVER FRELANDER 2 tires

Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal andInst all at ion).

Publi s hed: 11-May-2011
Parking Brake and Actuation - Parking Brake Shoes
Removal and Inst all ati on
Removal
• NOTE: If the parki ng brake s hoes or t he brake di scs have been removed for access to ot her components t hen DO NOTcarry out t he bedding i n procedure.
1. W ARNING: Do not work on or under a vehi cle s upported onl yby a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he wheel s and t ires .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal andInst all at ion).
2.
Remove both rear brake dis cs.
Refer t o: Brake Dis c (206-04 Rear Dis c Brake, Removal andInst all at ion).
3.
4.
5.

5. CAUTION: Make s ure the brake shoe s pri ng is not overs tretched.
Inst all t he brake s hoe adjus ter.
5.
Repeat t he above procedure for t he other s ide.6.
Inst all both rear brake dis cs.
Refer t o: Brake Dis c (206-04 Rear Dis c Brake, Removal andInst all at ion).
7.
Inst all t he wheel s and t ires .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal andInst all at ion).
8.
If neces sary, carry out t he parking brake s hoe bedding-i n procedure.
Refer t o: Parking Brake Shoes Bedding-In (206-05 Parking Brake andActuat ion, General Procedures ).
9.

Publi s hed: 11-May-2011
Anti-Lock Control - Front Wheel Speed Sensor
Removal and Inst all ati on
Removal
Rais e and s upport t he vehi cl e.
1.
Remove t he front wheel and t ire.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2.
Releas e t he fender spl as h shi el d.
Refer t o: Fender Spl ash Shi eld (501-02 Front End Body Panel s ,
Removal and Ins tall ati on).
3. 4.
T orque:
5 Nm 5.
Installation To i nst all , revers e t he removal procedure.
1.
If a new component i s t o be ins t al led, configure usi ng IDS.
2.

Publi s hed: 11-May-2011
Anti-Lock Control - Rear Wheel Speed Sensor
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he rear wheel and t ire.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal andInst all at ion).
2.
3.
4.

Publi s hed: 11-May-2011
Power Steering - Steering Gear
Removal and Inst all ati on
Removal
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he front road wheels and t ires.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2.
Remove t he front subframe as s embly.
Refer t o: Front Subframe (502-00 Uni -Body, Subframe and Mount ing
Syst em, Removal and Ins tall ati on).
3. Remove t he s teeri ng gear.
4.
Installation Inst all t he s teeri ng gear.
T orque: 105 Nm 1.
Inst all t he front subframe.
Refer t o: Front Subframe (502-00 Uni -Body, Subframe and Mount ing
Syst em, Removal and Ins tall ati on).
2.
Inst all t he wheel s and t ires .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
3.
Refi ll and bleed t he power st eeri ng.
Refer t o: Power St eering Sys tem Bleeding (211-00 St eering Sys tem -
General Informat ion, General Procedures ).
4.
Us ing onl y four wheel al ignment equi pment approved by Land Rover,
check and adjus t t he wheel al ignment.
5.

Publi s hed: 11-May-2011
Power Steering - Power Steering Fluid Cooler
Removal and Inst all ati on
Removal
1. W ARNING: Do not work on or under a vehi cle s upported onl yby a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he front wheel s and ti res .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal andInst all at ion).
2.
Remove t he front bumper.
Refer t o: Front Bumper (501-19 Bumpers , Removal and Ins tall ati on).
3.
Remove t he RH headlamp as s embly.
Refer t o: Headl amp As sembl y (417-01 Ext eri or Li ght ing, Removaland Inst all at ion).
4.
5.
Releas e t he power s t eering flui d res ervoir.Di sconnect t he qui ck rel eas e connect or.
6.

Publi s hed: 11-May-2011
Steering Linkage - Tie Rod End
Removal and Inst all ati on
Special T ool(s) 205-754
Spli tt er, Ball Joint s
Removal 1. W ARNING: Do not work on or under a vehi cle s upported onl y
by a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he front wheel .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2.
Loosen t he t ie-rod end l ock nut .
3. 4. CAUTION: Make s ure that the bal l joint ball
does not rot at e.
Releas e t he ti e-rod end ball joi nt from t he wheel
knuckle.
Speci al Tool (s ): 205-754 4.
5. CAUTION: Not e the number of t urns when
removi ng the ti e rod end to ai d i ns t allat ion.
Remove t he ti e-rod end.
5.
Installation 1. CAUTION: Make s ure that the ti e rod end is i nst all ed wit h
1.