2006 LAND ROVER FRELANDER 2 ECU

Releas e t he LH cabl e s ecuring cli p.All ow t he gears hift lever t o come t o rest in t heneutral pos it ion.Secure t he cabl e s elect or clip, wi thout dis turbingt he gears hi ft s elect or l ever pos it ion.
6.
Secure t he gear s elector cover.7.
Inst all t he s towage compart ment tray.8.
Inst all t he gear s elector knob.
Refer t o: Gears hi ft Lever Knob (308-06 ManualTrans mi ss ion/Transaxle Ext ernal Cont rol s , Removal andInst all at ion).
9.

Remove t he towi ng eye cover.21.
Remove t he 2 bolt s s ecuring bumper cover.22.
Releas e t he PAS li nes .23.
24. CAUTION: Be prepared to col lect es capingfluids .
• NOTE: Make s ure that all openi ngs are s ealed.
Releas e t he fuel li ne.
24.
Remove t he lower s upport ins ul ator.25.

Remove t he towi ng eye cover.
21.
Remove t he 2 bolt s s ecuring bumper cover.
22. Releas e t he PAS li nes .
23. 24. CAUTION: Be prepared to col lect es caping
fluids .
• NOTE: Make s ure that all openi ngs are s ealed.
Releas e t he fuel li ne.
24. Remove t he lower s upport ins ul ator.
25.

Secure t he eart h cabl e t o t he trans mi s si on mounti ng
bracket.
T orque: 25 Nm 4.
Inst all t he turbocharger outl et pi pe.
5. Inst all t he front flywheel cl osi ng panel .
T orque: 60 Nm 6.

Inst all t he power s t eering flui d li ne t o the cl ip.
15. Secure t he downpi pe cat alyt ic converter.
16. 17. W ARNING: Make sure t hat new nut s are
i ns t alled.
Connect t he LH and RH ti e-rod end bal l joint s .
T orque: 80 Nm 17.
18. W ARNING: Make sure t hat a new lower arm
ball joi nt nut is i ns t alled. CAUTION: Make s ure that t he bal l joi nt bal l does
not rot ate.
Inst all t he lower arm ball joi nt
T orque: 110 Nm 18.

19. W ARNING: Make sure t hat new nut s are
i ns t alled. CAUTION: Make s ure that t he bal l joi nt bal l does
not rot ate.
Connect both front s t abi li zer bar li nks to the s t abi li zer
bar.
T orque: 55 Nm 19.
20.
NOTE: RH i llus t rati on s hown, LH is s imil ar.
Inst all both the fender s plas h s hield ext ensi on panel s.
20.
Inst all t he front wheel s and ti res .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
21. Inst all t he 2 bolt s s ecuring t he t ransmis s ion mount ing
t o t he body mount ing.
T orque: 175 Nm 22.
Remove t he engi ne s upport .
23. Inst all t he s tart er mot or.
Refer t o: Start er Motor (303-06B Starti ng Sys t em - TD4
2.2L Dies el , Removal and Inst all at ion).
24.
Inst all t he gear s elector as s embl y.
Refer t o: Gears hi ft Li nkage (308-06 Manual Trans mi s si on/Trans axl e
External Controls , Removal and Inst all at ion).
25.

Connect t he clutch s l ave cyli nder hydrauli c hos e ands ecure wi th t he cli p.26.
Connect t he 1st and revers e gear pos it ion swi tchelectrical connect ors .27.
28. NOTE: If equipped.
• NOTE: An audibl e click i s heard when t he cli ps areful ly latched.
28.

Publi s hed: 11-May-2011
Manual Transmission/Transaxle External Controls - External Controls
Des cript ion and Operat ion
COMPONENT LOCATION
ItemPart NumberDescription
1-Shi ft cables2-Gear knob
3-Sel ect or lever as s embly
4-Sel ect or lever mount ing pl at e
INTRODUCTION
The manual t rans mi ss i on ext ernal cont rols compris e a sel ect or lever as s embly and 2 shi ft cables . The sel ect or al lows t hedri ver t o engage the 6 forward gears and revers e gear.
The s elect or lever ass embly is l ocat ed in a cent ral posi ti on on t he t ransmis s ion t unnel , bet ween the front driver andpass enger s eats and is s ecured t o t he transmis si on t unnel wit h 4 bol ts . The s elector lever ass embly is a non-s erviceabl emechani cal as sembl y.
Selecti ons made usi ng the sel ect or lever are pass ed t o t he t rans mis s ion l ever arm by t he s hift cables . Ball pins on thes elect or lever provide for the at tachment of t he s hift cabl es .
The s elect or has a vehicle s peed dependent sol enoi d int erl ock device. Thi s ensures that t he dri ver i s prevent ed fromacci dent al ly sel ect ing reverse gear.
Selector Lever and Shift Cables