2006 GREAT WALL HOVER Service Repair Manual

Automatic transmission-5
Table 2.1 Gear selection and its function
Gear selection function
1st-Gear
(manual 1
st-Gear ) The first gear is using for climbing and braking. It is a function which limits the speed of
the car. The speed limitation by engine is realized by reduce the opening degree of
throttle position.
2nd-Gear (automatic, manual
2
nd-Gear) In economic mode, it can process the 1
st and 2nd shifting operation when engage the 2nd
–Gear. The limitation of vehicle speed by engine is realized through reducing the
opening of throttle position. in 4WD 4 high, , the transmission will maintain 2
nd-Gear
position The manual mode and winter-Mode will only maintain 2nd-Gear 。
3rd-Gear
(automatic, manual 3rd-Gea) In economic mode and dynamic mode, it can process the shifting operation of 1
st, 2nd
and 3rd-Gear when engage the 3rd-Gear, and can reaches the very high vehicle speed. At
this time the locking clutch can process the locking action, refer to vehicle user manual.
The limitation of vehicle speed by engine is realized by reduce the opening of throttle
position. In 4WD 4 low, the transmission should be maintained in 3
rd –Gear position.
Under manual mode, the transmission will be kept in 3rd-Gear.
D-gear
(drive) It can process the 1
st, 2nd, 3rd and 4th –Gear position operation and gear-shifting operation
of (1-2), (1-3), (2-3), (2-4), (3-4), (4-3), (4-2), (3-1) and (2-1). This shifting operation is
processed by taking the vehicle speed, throttle position, throttle position switching
frequency (or forced Gear-decreasing) as the parameter. The locking clutch can process
the locking action in 3rd –Gear, 4
th-Gear according to the type of vehicle. Refer to user
manual of vehicle.
N-Gear
(neutral gear) Only the rear brake belt is engaged at this time. It determines whether the function can
be realized according to the vehicle speed, engine speed and throttle position. But the
gear-position sensor allows the starting of engine. Allow the slide of N-Gear.
R-Gear
(reverse gear) Set the anti-misoperation in forward function according to the vehicle speed, engine
speed and throttle position opening to realize the reverse operation. The gear-position
sensor can start the revers e lamp.
P-gear
(parking gear) Only the rear brake belt is engaged at this time. The function can be determined
according to the vehicle speed, engine speed and throttle position. The output shaft of
transmission is locked. The gear-position sensor can start the engine.

Automatic transmission-6
Selection of drive mode
The selection of drive mode includes a mode selection switch and indicator lamp. The drive mode selection switch is located
on the operating panel. It can provide the different mode selection according to the different type of car.
It has the optimal fuel economy when select the “normal” mode. At this time, the indicator lamp is not light. When select the
“dynamic” mode, the car will have the maximum dynamic performance and the “dynamic” mode indicator lamp is light. When select
the “snowland” mode, it will realize the starting of “2
nd-Gear”, the “snowland” mode indicator lamp is light, meanwhile the
“dynamic” mode indicator lamp will be closed. When select the manual mode, press down the “snowland” switch firstly, the
“manual” light will be light when the gear is in 3, 2, 1. When in manual mode, 1-2, 2-3, 3-4, 3-2, 2-1, 1-3, 3-1 is shifted by driver
manually and can not be shifted automatically. It can be used in car-racing etc. for the special mode of each model of car refers to
operation manual of user.
Operation instruction
Function
5 Brake function
Can decrease the gear-position in slope to improve the brake effect and increase the vehicle safety.
6 Speed-up function
It can select the manual shifting to increase the vehicle speed completely during the speed-up.
cautions
7 It must place the transmission in the P-Gear or N-Gear when start the engine.
8 It must place the transmission in P-Gear during the parking.
9 It must place the transmission in N-Gear when trail the car.
10 It must be powered off when remove the transmission.
11 It must be powered off when install the transmission.
The transmission processes the communication and calculation with the engine electronic control computer by the precision
central on-line computer. It not only save the fuel, but also provide the maximum mode function, including field, winter and
manual selection. It provides the two conditions, manual and electric for the fast race of racing player. It has racing capacity wh i ch
can compete the speed increasing with the manual transmission.
automatic
Having anti-slide function
It is allowable that the D-Gear
in “W” mode is used in
snowland and M-A integration
mode. automatic
automatic

Automatic transmission-7
Indicator lamp
Figure 2.2
control system
General
The transmission has two sets of control system, a electric control system and a hydraulic control system. The electric control
system monitors the vehicle parameter and adjusts the transmission performance; the hydraulic control system executes the
command of electric control system.
Electric control system
The electric control system consists of the sensor, TCU and 7 solenoid valves. TCU read in the data and make the output under the
control of software based on the value stored in Read Only Memory (ROM).
TCU controls the hydraulic control system and the control is realized through the valve and pump assembly. The system includes
7 solenoid valves, in which 6 valves are used to control the line pressure, operate the shift valve and hydraulic torque converter lock
clutch and switch on and off two regulating valves (Two regulating valves control the shift feel). The seventh solenoid valve is the
pressure regulating solenoid valve (VPS) which controls the shift feel with other three regulating valves. Figure 3.1 is the typical TCU
control system plan.
The figure includes all elements of electric control system involved in the section.
throttle position
open sensor
Engine speed
vehicle speed
Transmission
fluid temperature
mode selection
(instrument panel
/console )
Gear sensor
Forced step-
decreasingK line
shifting
logic
shifting
sensing
line
pressurehydraulic
control
system
Solenoid valve 1
Solenoid valve 2
Solenoid valve 3
Solenoid valve 4
Solenoid valve 5
Solenoid valve 6
Solenoid valve 7
pressure regulating
solenoid valve
Mode indicator lamp
Gear indicator lamp
set and other
necessary equipment
indication

Automatic transmission-8

Automatic transmission-9
Table 3.1 Feature parameter of temperature /resistance
-2013,638
5,177
2,278
177
7517,287
6,616
2,723
196
85


Figure 3.2 Pin number of temperature /resistance
Pin No. Wire color Connected solenoid valve
1 Red solenoid valve 1
2 Blue solenoid valve 2
3 yellow solenoid valve 3
4 orange solenoid valve 4
5 green solenoid valve 5
6 violet solenoid valve 6
7 brown solenoid valve 7
8 green solenoid valve 5
9 white temperature sensor
10 white temperature sensor
ohm
Temperature
Centigrade degree

Automatic transmission-10
Figure 3.3 Schematic diagram of temperature sensor position and solenoid valve wiring
2.Throttle position sensor
Figure 3.4 gear sensor
solenoid valve 4 (orange )
ground wire (2)
solenoid valve 7 power supply connectorolenoid valve 6 (violet ) ground wiretemperature sensor solenoid valve (red ) ground wire
solenoid
valve (green )
solenoid valve (yellow )
solenoid valve (blue ) ground wire
ground wire
ground wire

Automatic transmission-11
Diagnosis input
solenoid valve
1and 2 S1 and S2 is the normal open solenoid valve, which is used to set the gear-position with other switch
solenoid valve. It determines the static gear-position by operating the gear shift valve. Refer to Table 3.5,
S1 and S2 also send the pressure single to allow or prohibit the engagement with rear brake belt.
solenoid valve
3and 4 S3 and S4 are the normal-opened solenoid valve which is used to control the shifting quality and sequence in
combination. S3 control the open or close of the clutch. S4 is used to control the on and off of the front brake
belt regulating valve.
solenoid valve 5 S5 is the variable pressure solenoid valve which can release the pressure of gear-position shifting. It provides
the pressure signal to the clutch and brake belt regulator and controls the shifting pressure. S5 also provides
the pressure single to the torque converter clutch regulating valve.
solenoid valve 6 S6 is the normal-opened solenoid valve, which is used to the set the H/L level of pipeline pressure. The
pipeline pressure is high when the solenoid valve is closed.
solenoid valve 7 S7 is the normal-opened solenoid valve which is used to control the engagement status of torque converter
licking clutch. It makes the clutch to generate the action when the S7 is in opened status.
Table 3.4 Status and function of solenoid valve

Gear-position S1 S2
1st-Gear On On
2nd-Gear Off On
3rd-Gear Off Off
4th-Gear On Off
R-Gear One of them is in On position
at least.
N-Gear Off Off
P-Gear Off Off
Table 3.5 Logic status of solenoid valve in static gear-position

Automatic transmission-12

Shifting Initial shifting status Current variation of S5 Finished shifting status
1－2 S1 Off
S4 On 950mA－650mA
S4 Off

1－3 S1 Off
S2 Off
S3 On
S4 On 900mA－400mA
S3 Off
S4 Off
1－4 S2 Off
S3 On
S4 On 850mA－750mA
S3 Off
S4 Off
2－3 S2 Off
S3 On
S4 On 700mA－200mA
S3 Off
S4 Off
3－4 S1 On
S4 On 950mA－550mA
S4 Off

4－3 S4 On 950mA－700mA S1 Off
S4 Off
4－2 S3 On 800mA－500mA S1 Off
S2 On
S3 Off
4－1 S3 On
S4 On 1000mA－600mA
S2 On
S3 Off
S4 Off
3－2 S2 On
S4 On 550mA－400mA @ 20kph
800mA－600mA@60kph
1000mA－800mA@100kph S4 Off
3－1 S3 On
S4 On 1000mA－750mA S1 On
S2 On
S3 Off
S4 Off
2－1 S4 On 1000mA－500mA S1 On
S4 Off

Torque converter clutch
On
Off S7 On 1000mA－500mA
900mA－600mA S7 Off

Table 3.6 Operation of solenoid valve during shifting period