Page 377 of 933
NON SIDE OPENINGS ELEMENTS MECHAN ISMS
52
52 - 3
HATCHBACK LOCKING SYSTEM (old model)
DISMOUNTING
Loosen the screw for rod length adjustment (5) of the hatchback opening and detach the rod;
Remove the fork (2) and the gasket (4) releasing the hatchback opening control assembly (3)
Dismount the screws (1) and the special axle (6), releasing the guiding case (7 ) .
REMOUNTING
Perform in the reverse order the dismounting operations, the opening rod length adjustment
being performed with the hatchback opened and the lock blocked, in order that aft er three
consecutive drives, the rod mechanism control shall remain permanently tensioned.
HATCHBACK LOCKING SYSTEM
7
vnx.su
Page 378 of 933
NON SIDE OPENINGS ELEMENTS MECHAN ISMS
52
52 - 4
DISMOUNTING
Dismount the hatchback opening control
assembly (2 ) by removing t he fork (1) and
the gasket (2 ) .
Dismount the special screw (6) and release
the assembled lock (5), while beforehand the
rod (5) w as released .
REMOUNTING
Perform in the reverse order the dismounting operations.
HATCHBACK BALANCING DEVICE
DISMOUNTING
Dismount the ball joint (2 ) of the balanc-
ing device fixing (3) on the hatchback ( 1).
Dismoun t the balancing device attachment
on the hatchback frame (6), by removing the
locker (5) and the washer (4).
Release the balancing device.
REMOUNTING
Perform the dismounting operations in the reverse order.
HATCHBACK LOCKING SYSTEM
HATCHBACK LOCKING SYSTEM (after June 1
st 2001)
1
2
5
6
3
4
vnx.su
Page 379 of 933
NON SIDE OPENINGS ELEMENTS MECHAN ISMS
52
52 - 5
HATCHBACK BALANCING DEVICE
DISMOUNTING
Dismount the ball joint (2 ) of the balanc-
ing device fixing (3) on the hatchback ( 1).
Dismoun t the balancing device attachment
on the hatchback frame (6), by removing the
locker (5) and the washer (4).
Release the balancing device.
REMOUNTING
Perform the dismounting operations in the reverse order.
vnx.su
Page 380 of 933

WINDOWS
54
54 - 1
WINDSCREEN AND HATCHBACK GLASS REPLACEMENT
The replacement of t hese glasses is performed in case they a re broken, when they are not
according to the required overall dimensions or when they have manufacturing defects (image
distortions, cracks, etc).
PREPARING FOR MOUNTINGPosition the gasket (2) around the glass (1)
and place the assembly on a protection plate.
Place in the gasket channel all around the
gasket frame; a cotton cord ( 4 ) of 3 – 4
mm diameter, l eaving at its fre e ends (3)
about 20 cm of cord, and between the ends,
the distance shall not be more than 10 cm.
MOUNTING OF THE WINDSCREEN
M ount on the carriage body, the windscreen – cord - glass gasket assembly, so that the cord
ends are placed towards the inside of carriage body.
From the inside of the vehicle, successively draw each end of the cord, the drawing direction
being parallel with the glass surface, towards the surface inner part, perpendicular on the frame,
beginning with the lower part, in this way the gasket edge is lifted and then lowered on the frame.
At the outside, the gasket is seated by slightly and successively pressing it on glass, so that the
tightening is uniform on the whole windscreen contour and frame. DISMOUNTING OF A BROKEN
GLASS
If the glass or part of i t did not fa ll, t he
dismounting and the cleaning of the window
gaskets by the pieces of the broken glass
will be easier to be made by sticking a sheet
of paper on each surface.
WINDSCREEN AND HATCHBACK GLASS
vnx.su
Page 381 of 933
WINDOWS
54
54 - 2
54WINDSCREEN AND HATCHBACK GLASS
The cord must be always removed through the upper part of the windscreen.
Each time a windscreen is mounted, ensure the uniform setting of the whole assembly on the
carriage body by tapping several times with a rubber hammer, on the edge of the glass frame.
NOTE
Do not tap the glass on corners and on the two vertical si des.
After the windscreen mounting check out carefully the uniformity of the whole assembly and
then its water-proofing by splashing with a j et of water.
vnx.su
Page 382 of 933
WINDOWS
54
54 - 3
Dismount
the luggage compartment table.
Di sconnect the mass connection and the
hatchback defrosting supply connection.
Remove the glass together with the gasket,
by pushing it from the inside of the vehicle. Clean the gasket and place the glass in its
new gasket. The mounting of the hatchback glass – gasket
assembly, i s performed in the same way with
the windscreen mounting.
HATCHBACK GLASS REPLACEMENT
vnx.su
Page 383 of 933
EXTERNAL PROTECTIONS
55
55 - 1
REMOUNTING
Perform in the reverse
order the dismounting operations.
DISMOUNTING
Disconnect the fog projectors.
Dismo
unt :
-the attachment nut (1) of the front bumper (2) on the carriage body
-the attachment screws (3) and the cage nuts (5) of the bumper on the front cross bar.
-the lateral supports (4) are fixed by nuts on the iron core mounted in the front bumper. FRONT BUMPER
1
5
4
1
32
vnx.su
Page 384 of 933
EXTERNAL PROTECTIONS
55
55 - 2
DISMOUNTING
Disconnect
the rear fog spotlights, from the rear wiring.
Dismo unt :
- the nuts ( 1) and the attachment screws (3) of the rear bumper (4) on the carriage body,
by means of lateral supports (2), respectively by the bumper ends on the rear wheels passage.
-the attachment nuts (7) of the counterblade (6) on the carriage body.
D etach the rear bumper (5).
REMOUNTING
Perform the dismounting operations in the reverse order. RE
AR BUMPER
vnx.su