2003 MITSUBISHI SHOGUN Owner's Manual (in English)

D92J014A
2. Use the“H”or“M”button to select the
desired speed unit, then press the“SET”
button to enter the setting.
H-km
M-mile
D92J015A
3. If the km unit was selected in step 2, the
fuel consumption unit must be selected
continuously using the“H”or“M”but-
ton. The currently selected unit will
appear.
Use the“H”or“M”button to select the
desired fuel consumption unit, then
press the“SET”button to enter the set-
ting.
H-L/100Km
M-Km/L
D92J012A
4. Press the“SET”button to determine the
setting. The display will return to the
original display item.
NOTE
(1) If you select“M”(mile) unit in the step
2, fuel consumption is automatically
shown in the“mpg (mile per gallon)”.
(2) To cancel the unit setting procedure
before completion, press the button (A).
(3) The outside temperature and clock are
not shown during the unit selecting pro-
cedure.Instruments and controls
4-37
Div:
Out put date:

(5) If no buttons are pressed for more than
approx. 15 seconds, the currently
selected unit is set automatically. Then,
the display returns to the original dis-
play item.
D92M001A
When battery terminals are
disconnected
ED92M-C
The car type setting is erased when the
battery terminals are disconnected.
Re-enter the setting as follows:
1. Turn the ignition switch to the“ON”or
“ACC”position to activate the car set-
ting mode. The words“CAR TYPE”will
flash on the display.
D92M007A
2. In a 3-door models, press the“H”but-
ton once. (The word“SHORT”will be
displayed as shown in the illustration.)
In 5-door models, press“M”button
once. (The word“LONG”will be dis-
played as shown in the illustration.)
Instruments and controls
4-38Div:
Out put date:

D92M008A
3. Press the“SET”button to enter the set-
ting.
NOTE
If you select the car type incorrectly, take
the following action:
Before pushing the“SET”button: Press the
“H”or“M”button as appropriate to rectify
the selection.
After pressing the“SET”button: Press the
“SET”button for 2 seconds or more while
pressing the button (A) then perform the
setting procedure again from the begin-
ning.
Instruments and controls
4-39
Div:
Out put date:

D92A051D
RV meter*
ED92A-P
1. Display for function buttons
This shows the options for each function button.
2. Digital clock→page 4-53
3. Compass
This display shows the direction of the vehicle.
4. Function buttons
Press this button to select options shown in the display.
5.“ADJ”button→page 4-43, 4-56, 6-10, 6-25
Press this button to adjust the brightness, date and time on the
display and select the RDS language.
6.“DISP”button→page 4-41
Press this button to change the display.
Instruments and controls
4-40Div:
Out put date:

Change of display modePressing the“DISP”button shows modes
1 to 5 in order.
1. Trip computer information
(for petrol−powered vehicles only)
→page 4-46
2. Climate information→page 4-47
3. Audio information→page 6-2, 6-17
4. Date and time→page 4-53
5. Air conditioning→page 4-57
D92A052A
Basic operationsWhen the key is turned to“ACC”, the
screen switches on automatically.
Use the“DISP”button to select the desired
display.
WARNING
Don’t use the system for prolonged
periods while the engine is idling in
poorly ventilated areas such as
indoor garage, as you may suffer
injury as a result of exhaust gas inha-
lation.
CAUTION
(1) The display should not be oper-
ated or observed for prolonged
periods while driving, as a traf-
fic accident may result.
(2) When operating the system, stop
the vehicle in an area where
parking is permitted.Instruments and controls
4-41
Div:
Out put date:

NOTE
(1) Placing a cellular phone in the moni-
tor’s small storage compartment may
weaken the phone’s reception. This
does not indicate a fault with the sys-
tem.
(2) Use of wireless devices such as trans-
ceivers or a cellular phone near the
monitor may make the following con-
dition on the display. This does not indi-
cate a fault with the system.

The screen goes dark temporarily.

The compass may not show the cor-
rect direction.
(3) The following characteristics of the liq-
uid crystal display may be evident
under some circumstances and this
does not indicate a fault with the sys-
tem.

The appearance of small black
patches and spots of red, blue and
green lights.

The display goes dark, turns red or
moves slowly during cold weather.

The colour and brightness of the dis-
play change according to angle of
view.
Care of the monitorIf the monitor (the liquid crystal display)
becomes covered in fingerprints or other-
wise dirty, clean it with a soft and dry cloth.
NOTE
Don’t use a wet cloth or abrasive cleaner
as this may cause damage.
D92A053A
How to switch off or adjust the
brightness of the display
ED92L-B
Press the“ADJ”button to display the
options for the function buttons.
After 10 seconds, the display will be auto-
matically resumed.
Instruments and controls
4-42Div:
Out put date:

D92A054A
How to adjust the display brightness
1. Press the“BRIGHT”function button.
D92A055A
2. Adjust brightness as desired pressing
the“”or“”function buttons.
“”makes the display brighter.
“”makes the display darker.
3. The monitor will revert to the original dis-
play about 10 seconds after adjust-
ment with the function buttons is
finished.
NOTE
(1) Separate settings can be made for
when the lights are turned on and off.
(2) Whenever the monitor is not oper-
ated on, the previous display will be
resumed after about 10 seconds.
D92A056A
Switching off the display
1. Press the“BRIGHT”function button.Instruments and controls
4-43
Div:
Out put date:

D92A057A
(2) Press the“BLANK”function button to
turn off the display. To turn on the dis-
play again, press the“DISP”button.
Instruments and controls
4-44Div:
Out put date: