2003 MITSUBISHI SHOGUN oil temperature

D50A529D
Indication and warning lamps
ED50AOId
1- CRUISE indication lamp*→Page 5-54
2- ABS warning lamp*→Page 5-46
3- Brake warning lamp
4- Oil pressure warning lamp
5- Turn-signal indication lamps / Hazard warning indication lamps
6- Active stability control operation indication lamp*/
Active traction control operation indication lamp*
→Page 5-59
7- Active stability control OFF indication lamp*
→Page 5-59
8- Engine oil level warning lamp
9- Low fuel warning lamp
10- Check engine indication lamp
11- High-beam indication lamp
12- Charge warning lamp
13- A/T (automatic transmission) fluid temperature warning lamp
(vehicles with automatic transmission)14- Low washer fluid indication lamp*
15- Diesel preheat indication lamp (diesel-powered vehicles)
16- Front fog lamp indication lamp*
17- Fuel filter warning lamp (diesel-powered vehicles)
18- Rear fog lamp indication lamp
19- Supplemental restraint system (SRS) warning lamp
→Page 3-57
20- 2WD/4WD operation indication lamp→Page 5-26, 5-31
21- Rear differential lock indication lamp*→Page 5-35
22- Door-ajar warning lamp
23-
ECO indication lamp (petrol-powered vehicles)
24- Automatic transmission indication lamp
(vehicles with automatic transmission,
“N”indicator lamp is used also as A/T warning lamp)
→Page 5-19, 5-21
NOTE
To find information concerning the indication or warning lamps marked
by the symbol“→Page XX”, refer to the specified pages. For the other
indication and warning lamps, refer to the subsequent pages.
is a trademark of MITSUBISHI Motors Corporation.
Instruments and controls
4-6Div:
Out put date:

(7)Load
Do not drive with unnecessary articles
in the luggage compartment. Espe-
cially during city driving where fre-
quent starting and stopping is
necessary, the increased weight of the
vehicle will greatly affect fuel consump-
tion. Also avoid driving with unneces-
sary luggage, etc., on the roof; the
increased air resistance will increase
fuel consumption.
(8)Cold engine starting
Starting of a cold engine consumes
more fuel.
Unnecessary fuel consumption is also
caused by keeping a hot engine run-
ning. After the engine is started, com-
mence driving as soon as possible.
(9)Air conditioning*
The use of the air conditioning will
increase the fuel consumption.(10)Driving techniques for
engine
To take maximum advantage of the
fuel efficiency and other benefits of
the
engine, please
observe the following guidelines:
•TheECO indication lamp
in the meter cluster illuminates when
the vehicle is driven in a
fuel-efficient, environment-friendly
manner. Try to drive such that the
lamp is illuminated as much as pos-
sible. In particular, you should avoid
sudden starts and rapid accelera-
tion.
ECO indication lamp
→P.4-13
•Use of the air conditioner causes
fuel consumption and
carbon-dioxide emissions to
increase significantly. Avoid using
the air conditioner to cool the cabin
more than necessary.
*:is a trademark of MIT-
SUBISHI Motors Corporation.
Trailer towing
EC21AOIa
In order to tow a trailer with your vehicle,
have a trailer towing device that meets all
relevant regulations in your area, mounted
at an authorized MITSUBISHI dealer.
The regulations concerning the towing of a
trailer may differ from country to country.
You are advised to obey the regulations in
each area.
CAUTION
Danger of Accident!
A towing bar should be fitted by an
authorized MITSUBISHI dealer.
[For super select 4WD models]
When you are going to tow a trailer,
move the transfer shift lever to“4H”
position.
Selecting“2H”drive may increase
the differential oil temperature, result-
ing in possible damage to the driv-
ing system.
Further, the drive train will be sub-
jected to excessive loading possi-
bly leading to oil leakage, component
seizure, or other serious faults.
NOTE
Fitting of a towing bar requires special-
ized skills and equipment.
Contact an authorized MITSUBISHI dealer
for details. If you are going to tow a trailer,
pay careful attention to the following points.
Starting and driving
5-8Div:
Out put date:

CAUTION
(1) Do not operate the transfer shift
lever while the rear wheels of the
vehicle are slipping on a snow
covered road.
(2) Do not drive your vehicle in the
“4H”or“4L”position on paved
roads and highway; this would
result in early wear of the tyres,
increased fuel consumption and
possible noise generation.
It may also increase the differ-
ential oil temperature, resulting
in possible damage to the driv-
ing system parts. It is neces-
sary to operate the lever“2H”
position while driving under
these condition.NOTE
(1) When shifting from“2H”to“4H”soon
after driving the vehicle in a cold
weather area, the transmission gear
may make a noise. So try to shift the
gear while the vehicle is stopped.
(2) The 4WD operation indication lamp will
go out momentarily during shifting pro-
cess from“4H”to“4L”or vice versa, as
the shift lever passes through the neu-
tral position.
Be sure to operate the shift lever until
the 2WD/4WD operation indication
lamp illuminates again.
(3) There may be a case that the trans-
fer shift lever feels heavy when it is
moved from“4H”to“2H”with the steer-
ing wheel in turned position. This is nor-
mal and not any indication of trouble.
I31B009A
2WD/4WD operation indication lamp
EI48BXTa
When the ignition switch is in the“ON”
position, the 2WD/4WD operation indica-
tion lamp in the meter indicates the shift-
ing condition. The 2WD/4WD operation
indication lamp comes on at each trans-
fer shift lever position as follows:
Starting and driving
5-26Div:
Out put date:

CAUTION
(1) Do not operate the transfer shift
lever while the rear wheels of the
vehicle are slipping on a snow
covered road.
(2) Do not drive your vehicle in the
“4HLc”or“4LLc”position on
dry paved roads and highway;
this would result in early wear of
the tyres, increased fuel con-
sumption and possible noise
generation.
It may also increase the differ-
ential oil temperature, resulting
in possible damage to the driv-
ing system. Further, the drive
train will be subjected to exces-
sive loading, possibly leading to
oil leakage, component sei-
zure, or other serious faults. It is
necessary to operate the lever
“2H”or“4H”position while driv-
ing under these condition.
I30A052A
A: Front wheel lamp
B: Centre differential lock lamp
C: Rear wheel lamp
D: Low-range centre differential lock lamp2WD/4WD operation indication lamp
EI48BOH
When the ignition switch is in the“ON”
position, the 2WD/4WD operation indica-
tion lamp in the meter indicates the shift-
ing condition. The 2WD/4WD operation
indication lamp comes on at each trans-
fer shift lever position as follows:“2H”↔“4H”
Transfer shift lever posi-
tion2WD/4WD operation indi-
cation lamp
2H
Drive mode switching in
progress
4H
BlinkIlluminateRemain offStarting and driving
5-31
Div:
Out put date:

Correct 4-wheel drive
operation
EI32ABCa
By shifting lock to 4-wheel drive, both axles
of the vehicle are rigidly connected with
each other. This improves the traction char-
acteristics. When turning sharp corners or
moving forward and backward repeat-
edly, however, the drive line is stressed,
which is felt as a braking effect. A 4-wheel
drive vehicle can accelerate more quickly
and smoothly.
However, note that the braking distance is
not shorter than that of a rear-wheel drive
vehicle.
When using 4-wheel drive on rough roads
(snow, mud, sand, etc.), it is important to
operate the vehicle correctly.
NOTE
(1) The driving posture should be more
upright and closer to the wheel than
usual; adjust the seat to a good posi-
tion for easy steering and pedal opera-
tion. Be sure to wear the seat belt.
(2) After driving on rough roads, check
each part of the vehicle and wash it
thoroughly with water. Refer to the sec-
tions“Vehicle care”and“Inspection and
maintenance following rough road
operation”.
Driving on dry paved road and high-
waySelect“2H”(part time 4WD),“2H”or“4H”
(super select 4WD II) to drive on a dry
paved road. Especially on dry highway,
never select the“4H”or“4L”(part time
4WD),“4HLc”or“4LLc”(super select 4WD
II).
CAUTION
Selecting“4H”or“4L”(part time
4WD),“4HLc”or“4LLc”(super select
4WD II), to drive on dry paved road
will increase the fuel consumption
with possible noise generation and
early tyre wear.
It may also increase the differential
oil temperature, resulting in pos-
sible damage to the driving system.
Further, the drive train will be sub-
jected to excessive loading, possi-
bly leading to oil leakage, component
seizure, or other serious faults.Driving on snowy or icy roadsSet the transfer shift lever to“4H”or“4L”
(part time 4WD),“4H”or“4HLc”(super
select 4WD II) in accordance with the road
conditions, and then gradually depress the
accelerator pedal for a smooth start.NOTE
(1) The use of snow tyres and/or tyre
chains is recommended.
(2) In order to ensure that the anti-lock
brake system (ABS) will operate cor-
rectly in situations where tyre chains
have been fitted, drive in“4H”or“4L”
for part time 4WD, or in“4H”,“4HLc”or
“4LLc”for super select 4WD II.
(3) Maintain a safe distance between
vehicles, avoid sudden braking, and
use engine braking (downshifting).
CAUTION
Avoid sudden braking, sudden accel-
eration, and sharp turning; such
operations could cause skidding and
spinouts.Driving on sandy or muddy roadsSet the transfer shift lever to“4H”or“4L”
(part time 4WD),“4HLc”or“4LLc”(super
select 4WD II), and then gradually depress
the accelerator pedal for a smooth start.
Keep the pressure on the accelerator pedal
as constant as possible, and drive at low
speed.
Starting and driving
5-38Div:
Out put date:

Handling of cassette tapes
EH02B-Ad
CAUTION
To maintain the cassette tape player
in good condition, observe the fol-
lowing precautions.
(1) Do not use cassette tapes longer
than C-90, otherwise sound
quality and tape durability will be
greatly diminished.
(2) Keep the cassette tape in its
case to protect from tape loose-
ness and dust when it is not
used.
(3) Keep the cassette tape away
from direct sunlight, heat and
magnetic fields such as the
radio speakers.
(4) Before inserting the cassette,
make sure that the label is
adhered securely to the cas-
sette.
CAUTION
(5) A loose tape should be cor-
rected before use.
(6) Do not oil any part of the player
and do not insert any object
other than tape cassettes into
the slot, or the tape player may
be damaged. Also, avoid insert-
ing your fingers into the slot.
There is a danger of being burnt
by the hot internal parts.
H12F004A
Handling of compact discs
EH12E-Dc
(1) Use only the compact discs with the
mark shown in the illustration above.
(Playback of CD-R discs may cause
problems. CD-RW discs cannot be
played.)
The use of heart-shaped, octagonal, or
any other non-circular discs will result
in damage.
(2) When the temperature suddenly rises,
i.e. immediately after the heater is
turned on in cold weather, dew con-
densation on the disc or in the player
might occur resulting in failure of opera-
tion. In such a case, allow some time
before use.
(3) When the CD player is subjected to vio-
lent vibration as during off-road driv-
ing, detracking may result.
For pleasant driving
6-33
Div:
Out put date:

Genuine leather*
EK27A-Ac
1. Lightly wipe off with gauze or other soft
cloth soaked with a 5% aqueous solu-
tion of neutral detergent for wool.
2. Dip cloth in fresh water and wring it out
well. Using this cloth, wipe off the deter-
gent thoroughly.
3. Apply leather protecting agent to the
genuine leather surface.
NOTE
(1) If genuine leather is wet with water or
is washed in water, wipe off the water
as quickly as possible with a dry, soft
cloth.
(2) Slight stains on genuine leather may be
removed with a leather cleaner as well.
(3) The genuine leather surface may be
damaged if a nylon brush or syn-
thetic fibre is rubbed hard against it.
(4) Organic solvents such as benzine, alco-
hol and gasoline, acid or alkaline sol-
vents may discolour the genuine
leather surface. Be sure to use neu-
tral detergents.
(5) Dirty genuine leather seat may mil-
dew. Be very careful about oil stains
and remove them quickly.
(6) The genuine leather surface may
harden and shrink if it is exposed to
direct rays of the sun for long hours.
When your vehicle is parked, place it in
the shade as much as possible.(7) When the temperature of the vehicle
interior rises in summer, vinyl prod-
ucts left on the genuine leather seat
may deteriorate and stick to the seat.
Upholstery
EK25A-Aa
1. To maintain the value of your new
vehicle, handle the upholstery care-
fully and keep the interior clean.
Use a vacuum cleaner and brush to
clean the seats. If stained, vinyl and syn-
thetic leather should be cleaned with an
appropriate cleaner, and cloth fabrics
can be cleaned with either upholstery
cleaner or a 3% solution of neutral
detergent in lukewarm water.
2. Clean the carpeting with a vacuum
cleaner and remove any stains with car-
pet cleaner. Oil and grease can be
removed by lightly dabbing with a clean
colourfast cloth and stain remover.
Vehicle care
7-3
Div:
Out put date:

CAUTION
[For super select 4WD II]
When you are going to tow another
vehicle, move the transfer shift lever
to“4H”position.
Selecting“2H”drive may increase
the differential oil temperature, result-
ing in possible damage to the driv-
ing system.
Further, the drive train will be sub-
jected to excessive loading possi-
bly leading to oil leakage, component
seizure, or other serious faults.
NOTE
Your vehicle should only be used to tow
another vehicle if the weight of the other
vehicle is less than your vehicle.
Engine overheating
EN26AAY
If the water temperature gauge indication
remains in the overheating zone for a long
time, the engine may be overheating. If this
occurs, take the following corrective
measures:
1. Stop the vehicle in a safe place.
N26A208A
2. With the engine still running, raise the
bonnet to ventilate the engine compart-
ment.
A- Radiator cap
B- Radiator fan
C- Reserve tank
NOTE
Confirm that the radiator fan is turning. If
the fan is not turning, stop the engine
immediately and contact an authorized
MITSUBISHI dealer for assistance.
For emergencies
8-21
Div:
Out put date: