2003 MITSUBISHI SHOGUN Owner's Manual (in English)

H14B128A
Multi centre displayIf your vehicle is equipped with the“Multi
centre display”or the“RV meter”, follow-
ing items are displayed. (Refer to“Multi
centre display”on page 4-27 or“RV meter”
on page 4-40.)
A- Road surface freeze warning symbol
When the outside temperature drops below
about 3°C, the alarm sounds and the road
surface freeze warning symbol (A) flashes
for about 10 seconds.
CAUTION
There is a danger the road might be
frozen even when the symbol (A) is
not illuminated, so please take care
when driving.NOTE
If your vehicle is equipped with“Multi cen-
tre display”, turning the temperature adjust-
ment dial during the period of the alarm will
have no effect on the display.
After completion of the warning, set the
temperature. (Refer to“Outside
temperature”on page 4-28.)
H14B131A
RV meterB- Set temperature display
C- Outside air temperature display
D- Blowe speed indicator
E- Air flow indicator
F- Front defroster indicator
G- AUTO indicator
H- Air selection indicator
(Recirculation of inside air/incoming air
flow outside)
I- Air conditioning operation indicator
For pleasant driving
6-45
Div:
Out put date:

NOTE
The display changes automatically as fol-
lowing.
•Multi center display
The outside air temperature is usually dis-
played for several seconds while the tem-
perature control dial is operated.
•RV meter
When this mode has been displayed
automatically after operation of the air
conditioning, the display will revert to its
previous display after about 10 sec-
onds if no further adjustments are made.Operating the system as a manual
air conditioning
EH14CAF
If you operate the blower speed selection
dial or the mode selection dial as you
desired, the system is still automatically
controlled except selected function which
dial is operated. To return all operations to
automatic operation, set the dials to“AUT”
(AUTO) position.
H14D101A
Change of mode selection
EH14D-W
The mode selection dial is operated
according to the need.
Turn the dial and the air outlet will be
changed.
H14D109A
Multi centre displayIf your vehicle is equipped with the“Multi
centre display”or the“RV meter”, the air
flow indicator (A) is displayed as shown in
the multi centre display. (Refer to“Multi
centre display”on page 4-27 or“RV meter”
on page 4-40)
For pleasant driving
6-46Div:
Out put date:

H14D114A
RV meter
H16A296A
MODE SELECTION AIR OUTLETS
B, CB, C, D, EA*, C*, D, EA, C*, D, EA, C*
A:From front and side demister
B:From centre ventilators
C:From side ventilators
D:From under the instrument panel
E:From rear end of the centre console
*:means a small amount of air flow
(Face position)
Air flows to the upper part of the
passenger compartment.(Foot/face position)
Air flows to the upper part of the
passenger compartment, and the leg
area.(Foot position)
Air flows to the leg areas.(Foot/demister position)
Air flows to the leg areas, wind-
screen and door windows.(Demister position)
Air flows to the windscreen and the
door windows.
NOTE
Air always flows out from the side ventila-
tors regardless of the mode selection dial
position.
For pleasant driving
6-47
Div:
Out put date:

H14E015A
Change of air selection
EH14EOH
Every time the air selection switch is
pressed, alteration is made between out-
side air introduction and inside air recircu-
lation.
When inside air is recirculated, the indica-
tor lamp (A) comes on.
(Outside position)
Outside air is introduced into the pas-
senger compartment.
(Recirculation position)
Air is recirculated inside the passenger
compartment.NOTE
(1) Normally, use outside position to keep
the windscreen and side windows clear
and quickly remove fog or frost from
the windscreen.
If high cooling performance is desired,
or if the outside air is dusty or other-
wise contaminated, use the recircula-
tion position. Switch to the outside
position periodically to increase venti-
lation so that the windows do not
become fogged up.
(2) When the mode selection dial or the
blower speed selection dial is set to the
“AUT”(AUTO) position again after
manual operation, the air selection
switch will also be automatically con-
trolled.
CAUTION
Use of the recirculation position for
extended time may cause the win-
dows to fog up.
H14C079A
Change of the blower speed
EH13F-L
Adjust the fan speed by turning the blower
speed selection dial clockwise or anticlock-
wise.
The blower speed will gradually increase as
the dial is turned to the right.
For pleasant driving
6-48Div:
Out put date:

H14C103A
Multi centre displayIf your vehicle is equipped with“Multi cen-
tre display”or“RV meter”, blower speed
indicator (A) is displayed as shown in the
illustrations, (Refer to“Multi centre display”
on page 4-27 or“RV meter”on page 4-40)
H14C134A
RV meter1- High blower speed
2- Low blower speed
H14C080A
Air conditioning switch
EH13G-Ca
The air conditioning can be operated while
the engine is running.
If this switch is turned to the“AUT”(AUTO)
position, the air conditioning compressor
will start and the indicator lamp (A) will illu-
minate. To stop the air conditioning com-
pressor, press the centre of the dial.
Pressing it once more will start the air con-
ditioning compressor again.
For pleasant driving
6-49
Div:
Out put date:

CAUTION
(1) When using the air condition-
ing, the idling speed may slightly
increase as the air condition-
ing compressor is switched
on/off automatically. Especially
for vehicles with an automatic
transmission, while the vehicle
is stationary, fully depress the
brake pedal to prevent the
vehicle from creeping.
(2) On 3500 models, if a problem is
detected in the air conditioning
compressor, the air condition-
ing operation indicator lamp
blinks. Stop the vehicle in a safe
place, turn off the engine, then
restart the engine. If the air con-
ditioning operation indicator
lamp does not blink, there is no
problem. If it does blink, have it
checked at an authorized MIT-
SUBISHI dealer.
Demisting of the windscreen and
door windows
EH03DOH
CAUTION
For safety, make sure you have a
clear view through all windows.
To remove the frost or mist from the wind-
screen and door windows, use the mode
selection dial (“
”or“
”).
H03D151A
- To keep the windscreen and door
windows clear of mist, and to keep
leg area heating (when driving in rain
or snow).
1- Set the air selection switch (A) to the
outside position.
2- Set the mode selection dial to the“
”
position.
3- Select the desired blower speed by turn-
ing the blower speed selection dial.
4- Select the desired temperature by turn-
ing the temperature control dial.
5- Push the air conditioning switch (B).
For pleasant driving
6-50Div:
Out put date:

H03D152A
- For quick demisting
1- Set the mode selection dial to the“
”
position.
2- Set the blower speed to the maximum
blower speed position.
3- Set the temperature to the maximum
temperature position.
NOTE
(1) While the mode selection dial is set to
the“
”position, the air condition-
ing will operate automatically and the
outside air position will also be selected
automatically. This is done for opti-
mum performance.
(In the case, the air conditioning indi-
cator lamp will not change.)
(2) Do not set the temperature control dial
around the max. cool position. Cool air
will blow against the window glasses
and form mist on them.
H04F099A
Cooling
EH04FAOb
Set the mode selection dial to the“
”
position.
Set the air selection switch (A) to the out-
side position and push the air condition-
ing switch (B).
Adjust the temperature by turning the tem-
perature control dial clockwise or anticlock-
wise. Select the desired blower speed.
NOTE
If the outside air is dusty or otherwise con-
taminated, or if high cooling performance
is desired, set the air selection switch to the
recirculation position and the tempera-
ture control dial all the way to the left.
Switch to the outside position periodically
to increase ventilation so that the win-
dows do not become fogged up.
CAUTION
(1) When using the air condition-
ing, the idling speed may slightly
increase as the air condition-
ing compressor is switched
on/off automatically. Especially
for vehicles with an automatic
transmission, while the vehicle
is stationary, fully depress the
brake pedal to prevent the
vehicle from creeping.
(2) On 3500 models, if a problem is
detected in the air conditioning
compressor, the air condition-
ing operation indicator lamp
blinks. Stop the vehicle in a safe
place, turn off the engine, then
restart the engine. If the air con-
ditioning operation indicator
lamp does not blink, there is no
problem. If it does blink, have it
checked at an authorized MIT-
SUBISHI dealer.
For pleasant driving
6-51
Div:
Out put date:

H14F020A
To stop the air conditioning
EH14F-G
By setting the blower speed selection dial
to the“
”(OFF) position.
All operations will stop except the change
of air selection.
H18A091G
Rear heater* /
Rear air conditioning*
EH18A-Z
The rear heater/air conditioning can be
operated when the ignition switch is at the
“ON”position.
1- Main switch
2- Blower speed selection dial
3- Temperature control dial
For pleasant driving
6-52Div:
Out put date: