2003 MITSUBISHI SHOGUN clock

G24F028A
5. Put down the front end of the seat to the
floor. In this situation, the seat locking
system is unlocked automatically.
G24F025E
GH EE FF
6. Remove the covers (E) by turning the
knob (F) anticlockwise.
G- Unlock
H- Lock
G24F024E
7. Hold the seat as shown in the illustra-
tion and remove the seat by sliding it
backward.
Seat and seat belts
3-24Div:
Out put date:

D92A013D
Multi centre display*
ED92A-N
When the ignition switch is in the“ACC”position, the outside tem-
perature and clock are displayed in the multi centre display. When
the ignition switch is in the“ON”position, the average fuel con-
sumption is displayed besides outside temperature and digital
clock.
If your vehicle is equipped with an automatic air conditioning sys-
tem, set temperature, blower speed and air flow are displayed.
(Refer to“Automatic air conditioning”on page 6-43.)
A-Road surface freeze warning symbol
B-Outside temperature* / Set temperature*
C-Blower speed*
D-Air flow*
E-Average fuel consumption*
1/ Date*
2
F-Digital clock
G-DISP button (For vehicles with a MITSUBISHI genuine audio)
H-Display brightness / display unit selection button
*1: Average fuel consumption:
For petrol-powered vehicles without MITSUBISHI genuine
audio, only average fuel consumption is displayed.
For petrol-powered vehicles with MITSUBISHI genuine audio,
driving range and average speed can be displayed besides
average fuel consumption by pushing the DISP button in the
audio unit.
*2: Date - For diesel-powered vehicles
Instruments and controls
4-27
Div:
Out put date:

G15B093D
Digital clock
EG15BAIe
Following modes are available for clock adjustment:
•MITSUBISHI genuine audio:
“Auto mode” and “Manual mode”
• Non genuine audio:
“Manual mode” only
The selected mode is shown on the audio display.
“CT” displayed: Auto mode
“CT” not displayed: Manual mode For manual time adjustment, please refer to
“Manual mode ”below.
Auto mode
(MITSUBISHI genuine audio only)The automatic adjustment mode can set the local time automati-
cally by using the signal from the local RDS stations. In this mode,
“CT” (A) (Clock Time: sent with the RDS signal) is shown in the
audio display.
Instruments and controls
4-29
Div:
Out put date:

D92J014A
2. Use the“H”or“M”button to select the
desired speed unit, then press the“SET”
button to enter the setting.
H-km
M-mile
D92J015A
3. If the km unit was selected in step 2, the
fuel consumption unit must be selected
continuously using the“H”or“M”but-
ton. The currently selected unit will
appear.
Use the“H”or“M”button to select the
desired fuel consumption unit, then
press the“SET”button to enter the set-
ting.
H-L/100Km
M-Km/L
D92J012A
4. Press the“SET”button to determine the
setting. The display will return to the
original display item.
NOTE
(1) If you select“M”(mile) unit in the step
2, fuel consumption is automatically
shown in the“mpg (mile per gallon)”.
(2) To cancel the unit setting procedure
before completion, press the button (A).
(3) The outside temperature and clock are
not shown during the unit selecting pro-
cedure.Instruments and controls
4-37
Div:
Out put date:

D92A051D
RV meter*
ED92A-P
1. Display for function buttons
This shows the options for each function button.
2. Digital clock→page 4-53
3. Compass
This display shows the direction of the vehicle.
4. Function buttons
Press this button to select options shown in the display.
5.“ADJ”button→page 4-43, 4-56, 6-10, 6-25
Press this button to adjust the brightness, date and time on the
display and select the RDS language.
6.“DISP”button→page 4-41
Press this button to change the display.
Instruments and controls
4-40Div:
Out put date:

Adjusting the date and timeFollowing modes are available for clock adjustment:
•MITSUBISHI genuine audio:
“Auto mode” and “Manual mode”
• Non genuine audio:
“Manual mode” only
The selected mode is shown on the audio display.
“CT” displayed: Auto mode
“CT” not displayed: Manual mode
For manual time adjustment, please refer to “Manual mode ”below.
Auto mode
(MITSUBISHI genuine audio only)The automatic adjustment mode can set the local time automati-
cally by using the signal from the local RDS stations. In this mode,
“CT” (A) (Clock Time: sent with the RDS signal) is shown in the
audio display.
Instruments and controls
4-55
Div:
Out put date:
G15B093D

D92A053A
Manual modeThe manual adjustment mode is also avail-
able in case the“Auto”mode shows the
incorrect time when the adjacent local RDS
stations are located in a different time zone.
CAUTION
Only adjust the date and time when
stationary in an area where parking
and stopping are permitted.
NOTE
For safety, the date and time can only be
adjusted at speeds of less than 3 km/h
(2 mph).
For manual time adjustment, use the pro-
cedure below :
1. Press the“ADJ”button.
D92K021A
2. Press the“CLOCK”function button.
D92K022A
3. To change the month, day, year, hour,
minute and second readings, press the
“SELECT”function button. Each time
the“SELECT”function button is
pressed, the item to be adjusted will
switch between“hour”,“minute”,
“second”,“day”,“month”, and“year”.
Pressing the“SELECT”function but-
ton for more than 1 second will put it into
fast forward mode.
When“second”has been chosen, the
monitor display will automatically go to
0 seconds.
Instruments and controls
4-56Div:
Out put date:

D92K019A
4. Press the“ ”or “
”function button to
change to the desired number. Press-
ing “ ”or “
”function button for more
than 1 second, makes the value change
rapidly.
D92K020A
5. When the clock has been adjusted, press the “SET” function button.
NOTE
Disconnecting the battery terminal causes
the memory to be erased. If it has been dis-
connected, readjust the date and time by
following the procedure given in (1) through
(5).
Air conditioning
ED92K-Fa
When the fan speed dial and the ventila-
tor dial are set to “AUT ”, setting the tem-
perature control knob will produce
automatic selection of the ventilators
(excluding
and
) and automatic
adjustment of the air conditioner and out-
side air introduction.
This part of the manual concerns dis-
plays. To find out how best to use the air
ventilators, the switches and the air con-
ditioning, refer to “Automatic air
conditioning” on page 6-43.
Instruments and controls
4-57
Div:
Out put date: