2001 TOYOTA AVALON torque

B08678
N´m (kgf´cm, ft´lbf) : Specified torque
 Non-reusable partx 10
49.1 (500, 36)
 Crankshaft Front
Oil Seal
Relief Valve
Spring
Plug Oil Pump Body
Driven RotorDrive RotorOil Pump Body Cover
LU-8
- LUBRICATIONOIL PUMP
1233 Author
: Date
:
2001 AVALON (RM808U)

B04146
B04147
AB
Seal Width
3 - 4 mmAB Region ºYº Region ºXº LU-16
- LUBRICATIONOIL PUMP
1241 Author
: Date
:
2001 AVALON (RM808U)
(d) Engage the spline teeth of the oil pump drive gear with the
large teeth of the crankshaft, and slide the oil pump on the
crankshaft.
(e) Install the oil pump with the 9 bolts. Uniformly tighten the
bolts in several passes.
Torque:
10 mm head: 8 N´m (80 kgf´cm, 69 in.´lbf)
12 mm head: 19.5 N´m (200 kgf´cm, 14 ft´lbf)
2. INSTALL CRANKSHAFT POSITION SENSOR
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)
3. INSTALL BAFFLE PLATE TO NO.1 OIL PAN
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)
4. INSTALL NO.1 OIL PAN
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the oil pan,
oil pump and cylinder block.

Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing grooves.

Thoroughly clean all components to remove all the
loose material.

Using a non-residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the oil pan as shown in the illustra-
tion.
Seal packing: Part No. 08826-00080 or equivalent
Region ºXº is at the outer side of the bolt hole.
Region ºYº is at the inner side of the bolt hole.

Install a nozzle that has been cut to a or 3 - 4 mm
(0.12 - 0.16 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.

Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install the oil pan with the 17 bolts and 2 nuts. Uniformly
tighten the bolts and nuts in several passes.
Torque:
10 mm head: 8 N´m (80 kgf´cm, 69 in.´lbf)
12 mm head: 19.5 N´m (200 kgf´cm, 14 ft´lbf)
14 mm head: 37.2 N´m (380 kgf´cm, 27 ft´lbf)

P12568
AB
Seal Width
4 - 5 mm A
B
- LUBRICATIONOIL PUMP
LU-17
1242 Author
: Date
:
2001 AVALON (RM808U)
(d) Install the No.1 exhaust pipe support bracket with the 2
bolts.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
5. INSTALL OIL STRAINER
Install a new gasket and the oil strainer with the bolt and 2 nuts.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)
6. INSTALL NO.2 OIL PAN
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surface of the No.1 and
No.2 oil pans.

Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing grooves.

Thoroughly clean all components to remove all the
loose material.

Using a non-residue solvent, clean both sealing
surfaces.
NOTICE:
Do not use a solvent which will affect the painted surfaces.
(b) Apply seal packing to the No.2 oil pan as shown in the il-
lustration.
Seal packing: Part No. 08826-00080 or equivalent

Install a nozzle that has been cut to a 4 - 5 mm (0.16
- 0.20 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.

Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install the No.2 oil pan with the 10 bolts and 2 nuts. Uni-
formly tighten the bolts and nuts in several passes.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)
7. INSTALL TIMING PULLEYS (See page EM-21)
8. INSTALL TIMING BELT (See page EM-21)

LU-18
- LUBRICATIONOIL PUMP
1243 Author
: Date
:
2001 AVALON (RM808U)
9. INSTALL ADJUSTING STRUT AND PS PUMP DRIVE
BELT
(a) Temporarily install the adjusting strut with the bolt and nut.
(b) Install the drive belt with the pivot and adjusting bolts.
Torque: 43.1 N´m (440 kgf´cm, 32 ft´lbf)
(c) Tighten the nut.
Torque: 43.1 N´m (440 kgf´cm, 32 ft´lbf)
10. INSTALL A/C COMPRESSOR (See page EM-77)
11. INSTALL GENERATOR (See page CH-1)
12. INSTALL RH FENDER APRON SEAL
13. INSTALL FRONT EXHAUST PIPE (See page EM-77)
14. INSTALL RH FRONT WHEEL
15. FILL ENGINE WITH OIL
16. START ENGINE AND CHECK FOR LEAKS
17. RECHECK ENGINE OIL LEVEL

LU01W-03
B04141
Mark
LU-14
- LUBRICATIONOIL PUMP
1239 Author
: Date
:
2001 AVALON (RM808U)
REASSEMBLY
1. INSTALL DRIVE AND DRIVEN ROTORS
(a) Place the drive and driven rotors into pump body with the
marks facing the pump body cover side.
(b) Install the pump body cover with the 10 screws.
2. INSTALL RELIEF VALVE
Insert the relief valve and spring into the pump body hole, and
install the plug.
Torque: 49.1 N´m (500 kgf´cm, 36 ft´lbf)

MA0676B00995
MA01P-02
B08916
B09029
MA-8
- MAINTENANCEBODY
50 Author
: Date
:
2001 AVALON (RM808U)
BODY
INSPECTION
1. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
Tighten the following parts:

Front seat mount bolts
Torque: 37 N´m (375 kgf´cm, 27 ft´lbf)

Front suspension member-to-body mounting bolts
Torque: 181 N´m (1,850 kgf´cm, 134 ft´lbf)

Rear suspension member-to-body mounting nuts
Torque: 51 N´m (520 kgf´cm, 38 ft´lbf)
2. FINAL INSPECTION
(a) Check the operation of the body parts:

Hood:
Auxiliary catch operates properly
Hood locks securely when closed

Front and rear doors:
Door lock operates properly
Doors close properly

Luggage compartment door:
Door lock operates properly

Seats:
Seat adjusts easily and locks securely in any posi-
tion
Front seat back locks securely in any position
Folding-down rear seat backs lock securely
(b) Road test:

Check the engine and chassis for abnormal noises.

Check that the vehicle dose not wander or pull to
one side.

Check that the brakes work properly and do not
drag.

Do setting of the parking brake shoes and drum.
(c) Be sure to deliver a clean car and especially check:

Steering wheel

Shift lever knob

All switch knobs

Door handles

Seats

PP0B8-04
- PREPARATIONAIR CONDITIONING
PP-65
11 5 Author
: Date
:
2001 AVALON (RM808U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerSensor, ECT switch
Torque wrench
Dial indicatorMagnetic clutch
Plastic hammerMagnetic clutch

PP0M3-02
PP-30
- PREPARATIONAUTOMATIC TRANSAXLE
80 Author
: Date
:
2001 AVALON (RM808U)
EQUIPMENT
Straight edgeTorque converter clutch
Vernier calipersTorque converter clutch
Dial indicator or dial indicator with magnetic baseDrive plate
Hexagon Wrench (10 mm)
Torque wrench
OBD II scan tool