2001 TOYOTA AVALON garage door opener

BE0G5-04
I12836
I12837
I12838
BE-170
- BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
1774 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT GARAGE DOOR OPENER SWITCH
Press the switch and check that each LED (red) lights up.
Even if only one switch is found not to light up, replace it.
2. INSPECT GARAGE DOOR OPENER REGISTRATION
AND TRANSMITTING
HINT:
Use the home link tester made by KENT MORE for this test.
As it is necessary to record the code of the hand held transmit-
ter, customer's code will be erased. When the inspection com-
pletes, please register the customer's again.
(a) Check that the code of hand held transmitter for inspec-
tion can be recorded.
(See page
If the code can not be registered, replace garage door opener.
(b) Press the switch which an inspection code has been reg-
istered for and check that LED (green) of the home link
tester lights up.
If the LED (green) does not light up, replace the garage door
opener.

I04194
Wire Harness Side
- BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE-171
1775 Author
: Date
:
2001 AVALON (RM808U)
3. INSPECT GARAGE DOOR OPENER SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
1 - GroundConstantContinuity
2 - GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the power source or wire
harness.

BE0D3-03
I12840
Garage Door Opener
Enjine Room Junction Block

ECU-B Fuse
- BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE-169
1773 Author
: Date
:
2001 AVALON (RM808U)
LOCATION

BE0D2-03
I12837
BE-166
- BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
1770 Author
: Date
:
2001 AVALON (RM808U)
GARAGE DOOR OPENER SYSTEM
REGISTRATION PROCEDURE
1. NEW CODE REGISTRATION
NOTICE:

If pressing the switch of the original transmitter to
register the code, the system might operate.

When registering the transmitter codes such as for
garage or gate, check that there is nobody around
those places then register.
(a) Press the switch for the item to be registered for 20 se-
conds
HINT:
When transferring to registration mode, LED (red) blinks in 1 Hz
cycle.
(b) In the condition of (a), bring the original transmitter to with-
in 1-inch area around the garage door opener and press
the switch. (code transmitting).
HINT:
When code registration completes correctly, LED (red) blinks in
5.6 Hz cycle.

I03487
GARAGE DOOR
OPENER SWITCH
LEARN MODE
LED
OPERATION
ORIGINAL
TRANSMITTERPRESSED
ENTER
EXIT
ON
OFF20 sec
LED flashes
at a rate of 1 Hz
LED flashes at a
rate of 5.6 Hz RELEASE
ON
OFF
- BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE-167
1771 Author
: Date
:
2001 AVALON (RM808U)
New code registration timing chart.
If a code can not be registered, observe the following condi-
tions.
HINT:

If the battery of original transmitter is consumed.

Press the switch of the transmitter repeatedly in registra-
tion mode, as some transmitters stop transmitting for 1 to
2 seconds.

This system is not applicable to the garage door opener
which had been made before 1982.

If any signal from the transmitter is not received, the regis-
tration mode continues for 75 sec.
2. CODE DELETION
(a) Press the switches at both ends of garage door opener
simultaneously for 20 seconds.
HINT:
When transferring to deletion mode, LED (red) blinks in 6 Hz
cycle.
(b) When releasing the switch within 10 seconds after trans-
ferring to deletion mode, all the registered codes will be
erased.
HINT:
Press the switch until blinking in 5.6 Hz cycle stops, so that the
default code for check is set.

I03488
LED
OPERATION GARAGE DOOR
OPENER SWITCH
(Switch at both end)
ON
OFF CLEAR/DEFAULT
MODEPRESSED
LOAD DEFAULT
LED flashes at a rate of 5.6 HZ 10 SEC
20 SEC RELEASE
ON
OFFEnter erase mode to erase all 3 channels BE-168
- BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
1772 Author
: Date
:
2001 AVALON (RM808U)
Code deletion timing chart

BE-8
- BODY ELECTRICALTROUBLESHOOTING
1612 Author
: Date
:
2001 AVALON (RM808U)
POWER MIRROR CONTROL SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
ELECTRO CHROMIC MIRROR SYSTEM
SymptomSuspect AreaSee page
Electro Chromic Inner Mirror does not operate.
1. ECU-IG Fuse
2. Elector Chromic Inner Mirror
3. Wire Harness
BE-120
SEAT HEATER SYSTEM:
SymptomSuspect AreaSee page
Seat heaters do not operate.
(Driver's and Passenger's)1. SEAT HEATER Fuse
2. Ignition Main Relay
3. Wire Harness-
BE-122
-
Driver's seat heater does not operate.
1. Seat Heater Switch (Driver's)
2. Seat Heater
3. Wire HarnessBE-122
BE-122
-
Passenger's seat heater does not operate.
1. Seat Heater Switch (Passenger's)
2. Seat Heater
3. Wire HarnessBE-122
BE-122
-
Seat Heater temperature is too hot.1. Seat HeaterBE-122
GARAGE DOOR OPENER SYSTEM
SymptomSuspect AreaSee page
The equipment of which code has been registered does not oper-
ate.1. Garage Door Opener
2. Wire Harness
3. *BE-170
LED does not light up. (Even though either switch is pressed.)1. Garage Door Opener
2. Wire HarnessBE-170
LED does not light up. (Only one switch is pressed.)1. Garage Door OpenerBE-170
* As the GARAGE DOOR OPENER on the vehicle side seems to be normal, check the OPENER on the
equipment side, of which code has been registered.