2001 TOYOTA AVALON fuel filter

DI-46
- DIAGNOSTICSENGINE
202 Author
: Date
:
2001 AVALON (RM808U)
3 Check for open and short in harness and connector between ECM and A/F sen-
sor (bank 1, 2 sensor 1) (See page IN-30).
NG Repair or replace harness or connector.
OK
4 Check resistance of A/F sensor heater (bank 1, 2 sensor 1) (See page SF-79).
NG Replace A/F sensor.
OK
5 Check air induction system (See page SF-1).
NG Repair or replace.
OK
6 Check fuel pressure (See page SF-6).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter (See page SF-1).
OK
7 Check injector injection (See page SF-23).
NG Replace injector.
OK

FI6588
FI6538
A00064
10 V
/Division10 V
/Division
GND GND
100 msec./Division (Idling)1 msec./Division (Idling)
Injection duration
(Magnification) Injector Signal Waveform
DI-62
- DIAGNOSTICSENGINE
218 Author
: Date
:
2001 AVALON (RM808U)
Reference: INSPECTION USING OSCILLOSCOPE
With the engine idling, check the waveform between terminals #10 - #60 and E01 of the ECM connector.
HINT:
The correct waveform is as shown.
OK Go to step 5.
NG
4 Check resistance of injector of misfiring cylinder (See page SF-19).
NG Replace injector.
OK
Check for open and short in harness and con-
nector between injector and ECM (See page
IN-30).
5 Check fuel pressure (See page SF-6).
NG Check and repair fuel pump, fuel pipe line and
filter (See page SF-1).

- DIAGNOSTICSENGINE
DI-109
265 Author
: Date
:
2001 AVALON (RM808U)
4 Check resistance of A/F sensor heater (See page SF-79).
NG Replace A/F sensor.
OK
5 Check air induction system (See page SF-1).
NG Repair or replace.
OK
6 Check fuel pressure (See page SF-6).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter (See page SF-1).
OK
7 Check injector injection (See page SF-23).
NG Replace injector.
OK
Replace A/F sensor.
8 Perform confirmation driving pattern (See page DI-106).
Go

- DIAGNOSTICSENGINE
DI-1 13
269 Author
: Date
:
2001 AVALON (RM808U)
5 Check air induction system (See page SF-1).
NG Repair or replace.
OK
6 Check fuel pressure (See page SF-6).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter (See page SF-1).
OK
7 Check injector injection (See page SF-23).
NG Replace injector.
OK
Replace A/F sensor.
8 Perform confirmation driving pattern (See page DI-106).
Go
9 Is there DTC P1133 or P1153 being output again?
YES Check and replace ECM (See page IN-30).
NO

A11669
14
3 2
B-R
L LG-B
L-Y
LG 1
4
2
43
21
43
21
43
21
43
2
Ignition Coil
with Igniter
No.2
No.3
No.4
No.5
No.6
Noise
Filter B-Y W-BB-W
GR
13 No.1B-W
B-W B-W B-W
B-WB-Y
B-Y B-Y B-Y B-Y B-Y
W-B
W-B
W-B
W-B W-B
1
B-W
B-WW-B
B-W
B-W
B-WW-B W-B W-B
B-W
W-BIGT1
IGF IGT2
IGT3
IGT4
IGT5
IGT6 11
12
13
14
15
16
25 E4
E4
E4
E4
E4
E4
E4ECM
Battery
EC ED
115
2B
B-O
2F 1C28
3
IG Switch72
14 IG2 Reray
2G
2C 2CIG2
AM2 72
1J B-O
7
6W-R
W-R4
IF1Engine Room J/B
Driver Side J/BB
Fusible
Link
Block
FL
Main 1F6 F7
B-W
1 B-Y
B-Y B-Y B-Y
W-B
DI-1 18
- DIAGNOSTICSENGINE
274 Author
: Date
:
2001 AVALON (RM808U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P1300 is displayed, check No.1 ignition coil with igniter circuit.

If DTC P1305 is displayed, check No.2 ignition coil with igniter circuit.

If DTC P1310 is displayed, check No.3 ignition coil with igniter circuit.

If DTC P1315 is displayed, check No.4 ignition coil with igniter circuit.

If DTC P1320 is displayed, check No.5 ignition coil with igniter circuit.

If DTC P1325 is displayed, check No.6 ignition coil with igniter circuit.

If DTCs P1300, P1315 and P1325, are output simultaneously, IGF1 circuit may be open or short.

If DTCs P1305, P1310 and P1320, are output simultaneously, IGF2 circuit may be open or short.

Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich, etc. at the time of the malfunction.
1 Check spark plug and spark (See page DI-58).

- DIAGNOSTICSENGINE
DI-55
211 Author
: Date
:
3 Check mass air flow meter (See page SF-31) and engine coolant temperature
sensor (See page SF-73).
NG Repair or replace.
OK
4 Check for spark and ignition (See page IG-1).
NG Repair or replace.
OK
5 Check fuel pressure (See page SF-6).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter.
OK
6 Check gas leakage on exhaust system.
NG Repair or replace.
OK

A07428
86
5 43 2
1
910
7
117
A09699
8 mm Hexagon Wrench
A09695
Throttle Body
Bracket
Engine
Hanger
EM-68
- ENGINE MECHANICALCYLINDER HEAD
1052 Author
: Date
:
2001 AVALON (RM808U)
26. INSTALL INTAKE MANIFOLD ASSEMBLY
(a) Install the intake manifold, delivery pipe and injectors as-
sembly with the 9 bolts, 2 plate washers and 2 nuts. Uni-
formly tighten the bolts and nuts in several passes and in
the sequence shown.
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
(b) Connect the fuel inlet hose to the fuel filter.
CAUTION:
Perform connecting operations of the fuel tube connector
(quick type) after observing the precaution.
(See page SF-1)
(c) Connect the heater hose to the intake manifold.
27. RETIGHTEN WATER OUTLET MOUNTING BOLTS
AND NUTS
Tighten the 2 bolts and 2 nuts.
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
28. INSTALL AIR INTAKE CHAMBER ASSEMBLY
(a) Using an 8 mm hexagon wrench, install a new gasket and
the air intake chamber assembly with the 2 bolts and 2
nuts. Uniformly tighten the bolts and nuts in several
passes.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(b) Install the No.1 engine hanger with the 2 bolts.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
(c) Install the throttle body bracket with the 2 bolts.
Torque: 19.5 N´m (200 kgf´cm, 14 ft´lbf)
(d) Connect the PCV hose to the PCV valve on the RH cylin-
der head.
(e) Connect the ground strap and cable to the intake air con-
trol valve for the ACIS.
(f) Connect the ground cable and strap with the nut.
Torque: 14.5 N´m (145 kgf´cm, 10 ft´lbf)
(g) Connect the ground cable to the air intake chamber.
(h) Connect the brake booster vacuum hose to the throttle
body.
(i) Connect the 2 water bypass hoses to the throttle body.
(j) Connect the air assist hose to the throttle body.
(k) Connect the purge hose to the emission control valve set.
(l) Connect the 2 vacuum hoses to the vacuum tank for
ACIS.
(m) Connect the engine wire clamp to the emission control
valve set.

A07505
(p)
(q)
(r)(o)
(n)
(m)
(n)
A09695
Throttle Body
Bracket
Engine
Hanger
A09699
8 mm Hexagon Wrench
A05074(b) (c)
EM-32
- ENGINE MECHANICALCYLINDER HEAD
1016 Author
: Date
:
2001 AVALON (RM808U)
(m) Disconnect the brake booster vacuum hose from the
throttle body.
(n) Disconnect the 2 water bypass hoses from the throttle
body.
(o) Disconnect the air assist hose from the throttle body.
(p) Disconnect the purge hose from the pipe on the emission
control valve set.
(q) Disconnect the 2 vacuum hoses from the vacuum tank for
the ACIS.
(r) Disconnect the engine wire clamp from the emission con-
trol valve set.
(s) Remove the 2 bolts and No.1 engine hanger.
(t) Remove the 2 bolts and throttle body bracket.
(u) Using an 8 mm hexagon wrench, remove the 2 bolts, 2
nuts, the air intake chamber assembly and gasket.
9. REMOVE INTAKE MANIFOLD ASSEMBLY
(a) Disconnect the 6 injector connectors.
(b) Disconnect the fuel inlet hose from the fuel filter.
CAUTION:
Perform connecting operations of the fuel tube connector
(quick type) after observing the precautions.
(See page SF-1)
(c) Disconnect the heater hose from the intake manifold.