1995 TOYOTA SUPRA torque

RADIATOR ASSEMBLY
1. A/T:
INSTALL OIL COOLER TO LOWER TANK
(a) Clean the O±ring contact surface of the lower tank and oil
cooler.
(b) Install new O±ring (1) to the oil cooler (2).
(c) Install the oil cooler (2) to the lower tank (3).
(d) Install the plate washers (4), and nuts (5).
Torque: 8.3 NVm (85 kgfVcm, 74 in.Vlbf)
(e) Install the inlet pipes (6).
Torque: 15 NVm (150 kgfVcm, 11 ftVlbf)
HINT: Face the inlet pipes in the same direction they were be-
fore disassembly.
2. INSPECT LOCK PLATE
Inspect the lock plate for damage.
HINT:
wIf the sides of the lock plate groove are deformed,
reassembly of the tank will be impossible.
wTherefore, first correct any deformation with pliers or
similar object. Water leakage will result if the bottom of
the lock plate groove is damaged or dented. Therefore,
repair or replace if necessary.
3. INSTALL NEW O±RINGS AND TANKS
(a) After checking that there are no foreign objects in the lock
plate groove, install the new O±ring without twisting it.
HINT: When cleaning the lock plate groove, lightly rub it with
sand paper without scratching it.
(b) Install the tank without damaging the O±ring.
(c) Tap the lock plate with a soft±faced hammer so that there is
no gap between it and the tank. EG±350
± ENGINECOOLING SYSTEM

Engine Coolant Temperature (ECT)
Switch
ECT SWITCH INSPECTION
1. REMOVE ENGINE UNDER COVER
2. DRAIN ENGINE COOLANT
3. REMOVE ECT SWITCH
(a) Disconnect the ECT switch connector.
(b) Remove the ECT switch.
(c) Remove the O±ring from the ECT switch.
4. INSPECT ECT SWITCH
(a) Usin g an oh mme te r, ch e ck th a t th e re is no co n tin u ity
between the terminals when the coolant temperature is
above 97°C (207°F).
(b) Using an ohmmeter, check that there is continuity between
the terminals when the coolant temperature is below 88°C
(190°F).
If continuity is not as specified, replace the switch.
5. REINSTALL ECT SWITCH
(a) Install a new O±ring to the ECT switch.
(b) Apply soapy water to the O±ring.
(c) Install the ECT switch.
Torque: 7.4 NVm (75 kgfVcm, 65 in.Vlbf)
(d) Connect the ECT switch connector.
6. REFILL WITH ENGINE COOLANT
7. START ENGINE AND CHECK FOR LEAKS
8. REINSTALL ENGINE UNDER COVER
No.1 Radiator Fan Relay
(ºRADIATOR FAN RELAYº)
RADIATOR FAN RELAY INSPECTION
1. w/ Auto Spoiler:
REMOVE LH HEADLIGHT
2. w/o Auto Spoiler:
REMOVE ENGINE UNDER COVER
3. REMOVE RADIATOR FAN RELAY
4. INSPECT RADIATOR FAN RELAY
A. Inspect relay continuity
(a) Using an ohmmeter, check that there is continuity between
terminals 3 and 4.
(b) Check that there is no continuity between terminals 1 and 2.
If continuity is as specified, replace the relay. EG±356
± ENGINECOOLING SYSTEM

SERVICE SPECIFICATIONS
SERVICE DATA
 
 
Thermostat 
 
Valve opening temperature
Valve lift at 95°C (203°F) 
 
80±84°C (176±183°F)
8.5 mm (0.335 in.) or more
 
 
 
Radiator cap 
 
 
Relief valve opening pressure STD
Minimum 
 
 
93±123 kPa
(0.95±1.25 kgf/cm2, 13.5±17.8 psi)
78 kPa (0.8 kgf/cm
2, 11.4 psi)
 
 
Electric
cooling fan 
 
Rotating amperage 
 
2.5±4.5 A
TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
 Engine drain plug x Cylinder block 29 300 22
 Fan x Fluid coupling 7.4 75 65 in.Vlbf
 Water pump x Cylinder block 21 210 15
 Water pump x No.2 water bypass pipe 21 210 15
 Generator x Water pump 37 380 27
 Generator x Cylinder block 37 380 27
 Water bypass outlet x Cylinder head (2JZ±GE) 8.8 90 78 in.Vlbf
 Water outlet x Cylinder head (2JZ±GTE) 21 210 15
 Water inlet x Water pump (2JZ±GE) 8.8 90 78 in.Vlbf
 Water inlet x Water pump (2JZ±GTE) 21 210 15 Upper radiator support x Body 15 155 11 ECT switch x Radiator (2JZ±GTE) 7.4 75 65 in.Vlbf Fluid coupling x Water pump 16 165 12 Oil cooler x Radiator lower tank (A/T) 8.3 85 74 in.Vlbf Oil cooler x Oil cooler pipe (A/T) 15 150 11
EG±358± ENGINECOOLING SYSTEM

EMISSION CONTROL SYSTEMS (2JZ±GE)
SYSTEM PURPOSE
The emission control systems are installed to reduce the amount of CO, HC and NOx exhausted from the
engine ((3), (4) and (5)), to prevent the atmospheric release of blow±by gas±containing HC (1) and evapo-
rated fuel containing HC being released from the fuel tank (2).
The function of each system is shown in the following table.
 System Abbreviation Function
 
 
 
 
 
 
(1) Positive Crankcase Ventilation
(2) Evaporative Emission Control
(3) Exhaust Gas Recirculation
(4) Three±Way Catalytic Converter
(5) Sequential Multiport Fuel Injection* 
 
 
 
 
 
PCV
EVAP
EGR
TWC
SFI 
 
 
 
 
 
Reduces HC
Reduces evaporated HC
Reduces NOx
Reduces CO, HC and NOx
Injects a precisely timed, optimum amount of fuel for re-
duced exhaust emissions
Remark: * For inspection and repair of the SFI system, refer to the SFI section this manual.
PREPARATION
RECOMMENDED TOOLS
09082±00050 TOYOTA Electrical Tester Set


EQUIPMENT
 
 Tachometer 
 
 
 Torque wrench 
 
 
 Vacuum gauge 
 
± ENGINEEMISSION CONTROL SYSTEMS (2JZ±GE)EG±163

EMISSION CONTROL SYSTEMS (2JZ±GE)
SYSTEM PURPOSE
The emission control systems are installed to reduce the amount of CO, HC and NOx exhausted from the
engine ((3), (4) and (5)), to prevent the atmospheric release of blow±by gas±containing HC (1) and evapo-
rated fuel containing HC being released from the fuel tank (2).
The function of each system is shown in the following table.
 System Abbreviation Function
 
 
 
 
 
 
(1) Positive Crankcase Ventilation
(2) Evaporative Emission Control
(3) Exhaust Gas Recirculation
(4) Three±Way Catalytic Converter
(5) Sequential Multiport Fuel Injection* 
 
 
 
 
 
PCV
EVAP
EGR
TWC
SFI 
 
 
 
 
 
Reduces HC
Reduces evaporated HC
Reduces NOx
Reduces CO, HC and NOx
Injects a precisely timed, optimum amount of fuel for re-
duced exhaust emissions
Remark: * For inspection and repair of the SFI system, refer to the SFI section this manual.
PREPARATION
RECOMMENDED TOOLS
EQUIPMENT
 
 Tachometer 
 
 
 Torque wrench 
 
 
 Vacuum gauge 
 
± ENGINEEMISSION CONTROL SYSTEMS (2JZ±GE)EG±163

3. REMOVE EGR VALVE
(a) Disconnect these hoses from the EGR valve:
(1) Vacuum hose
(2) Pressure hose
(b) Remove the 2 nuts, EGR valve and gasket.
4. INSPECT EGR VALVE
Check for sticking and heavy carbon deposits.
If a problem is found, replace the EGR valve.
5. REINSTALL EGR VALVE
(a) Place a new gasket on the intake air connector.
(b) Install the EGR valve with the 2 nuts.
Torque: 27 NVm (280 kgfVcm, 20 ftVlbf)
(c) Reconnect the following hoses to the EGR valve:
wVacuum hose
wPressure hose
6. REINSTALL EGR GAS TEMPERATURE SENSOR
Torque: 20 NVm (200 kgfVcm, 14 ftVlbf)
7. REINSTALL EGR PIPE
(a) Temporarily install the union nut of the EGR pipe.
(b) Install a new gasket and the EGR pipe with the 2 bolts.
Torque: 21 NVm (210 kgfVcm, 15 ftVlbf)
(c) Tighten the union nut of the EGR pipe.
Torque: 64 NVm (650 kgfVcm, 47 ftVlbf)
EG±170± ENGINEEMISSION CONTROL SYSTEMS (2JZ±GE)

SERVICE SPECIFICATIONS
TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
 EGR valve x Intake air connector 21 210 15
 EGR gas temperature sensor x EGR valve 20 200 14 
 EGR pipe x Cylinder head
 
 27
 
 280
 
 20
 EGR valve x EGR pipe 64 650 47
 No.2 front exhaust pipe (Front TWC) x Exhaust manifold 62 630 46
 Pipe support bracket x Transmission 43 440 32 
 No.2 front exhaust pipe (Front TWC) x Front exhaust pipe (Rear TWC) 
 43 
 440 
 32
 Front exhaust pipe (Rear TWC) x Center exhaust pipe 43 440 32
 Sub heated oxygen sensor (California only) x Front exhaust pipe 20 200 14
EG±174± ENGINEEMISSION CONTROL SYSTEMS (2JZ±GE)

EMISSION CONTROL SYSTEMS (2JZ±GTE)
SYSTEM PURPOSE
The emission control systems are installed to reduce the amount of CO, HC and NOx exhausted from the
engine ((3), (4) and (5)), to prevent the atmospheric release of blow±by gas±containing HC (1) and evapo-
rated fuel containing HC being released from the fuel tank (2).
The function of each system is shown in the following table.
 System Abbreviation Function 
 
 
 
 
 
(1) Positive Crankcase Ventilation
(2) Evaporative Emission Control
(3) Exhaust Gas Recirculation
(4) Three±way Catalytic Converter
(5) Sequential Multiport Fuel Injection*
 
 
 
 
 
 
PCV
EVAP
EGR
TWC
SFI
 
 
 
 
 
 
Reduces HC
Reduces evaporated HC
Reduces NOx
Reduces CO, HC and NOx
Injects a precisely timed, optimum amount of fuel for reduced
exhaust emissions
Remark: * For inspection and repair of the SFI system, refer to the SFI section this manual.
PREPARATION
RECOMMENDED TOOLS
09082±00050 TOYOTA Electrical Tester Set


EQUIPMENT
 
 Tachometer 
 
 
 
Torque wrench 
 
 
 
Vacuum gauge 
 
± ENGINEEMISSION CONTROL SYSTEMS (2JZ±GTE)EG±175