2013 SSANGYONG KORANDO Service Manual

8710-01
Operating process
- The ignition is turned OFF.
19. SLEEP MODE
If the state of the LOCK switches of driver/passenger/rear doors and tailgate is not changed for 6
seconds with the all doors including tailgate closed and IGN OFF (ignition key removed), even if the
state is not LOCK, the system enters the sleep mode to power down. 1.
If any condition of the (1) is not met, the system enters the wake up mode immediately. 2.
When the room lamp, key hole lamp, tail lamp, or power window is already activated, or all doors are
closed for continuous 30 seconds after the door UNLOCK under the conditions stated in (1), the
system waits in normal mode. If the lamps or power window is deactivated and no change is
detected for 6 seconds after all doors are closed, the system enters the sleep mode. 3.
When the front room lamp is ON, the system turns of the room lamp in 10 minutes and enters the
sleep mode after 6 seconds. 4.
If the coming home light is ON, the system enters the sleep mode when the coming home light
switching off conditions are met. 5.
The sleep mode is deactivated when a door is opened or key is inserted. 6.

LH/RH turn signal lamp control
The LH/RH turn signal lamp switch is turned ON with IGN ON.
The LH/RH turn signal lamp flashes 75 times per minute (T1), and the internal buzzer sounds at
intervals of 0.4 sec. ON/0.4 sec. OFF.
The LH/RH turn signal lamp and internal buzzer are deactivated when the LH/RH turn signal lamp
switch is turned OFF. A.
B.
C. Operation 1.
Abnormal current (less than 3 A or more than 7 A) detection signal is input while the lamp is ON.
The LH/RH turn signal lamp flashes 100 times per minute (T2), and the internal buzzer sounds at
intervals of 0.3 sec. ON/0.3 sec. OFF. D.
E. Operation 2.
The LH/RH turn signal lamp is activated only with IGN ON. F. Operation 3.
20. FLASHER FUNCTION
The LH/RH turn signal lamp flashes 3 times once the corresponding lamp switch is turned ON.
When the LH turn signal lamp switch is turned OFF during the 3 times flashing, the turn signal
lamp goes out after the flashing operation.
When the LH turn signal lamp switch is turned ON during the 3 times flashing, the turn signal lamp
flashes 3 more times.
When the RH turn signal lamp switch is turned ON during the 3 times flashing, the LH turn signal
lamp goes out immediately and the RH turn signal lamp flashes 3 times before switching off. -
-
-

8710-01

Hazard warning lamp switch control
The hazard warning lamp switch is turned ON with IGN ON or OFF.
The hazard warning lamp flashes 75 times per minute (T1), and the internal buzzer sounds at
intervals of 0.4 sec. ON/0.4 sec. OFF.
The hazard warning lamp and internal buzzer are deactivated when the hazard warning lamp switch
is turned OFF. A.
B.
C. Operation 1.
Operation 1. Abnormal current (less than 3 A or more than 7 A) detection signal is input while the
lamp is ON.
The hazard warning lamp flashes 100 times per minute (T2), and the internal buzzer sounds at
intervals of 0.3 sec. ON/0.3 sec. OFF. D.
E. Operation 2.
Hazard warning lamp functions at B+ or more.
The allowed time difference between the LH and RH turn signal lamp operations is within 0.1
seconds.
The hazard warning lamp overrides the turn signal lamp.
Priority of internal buzzer (chime) operation while the hazard warning lamp is ON
(Seat belt reminder > Ignition key reminder > Sunroof open > Tail lamp ON > Hazard warning lamp
> Turn signal lamp) -
-
-
-

8710-01

AUTO hazard warning flasher control
The hazard warning lamp comes on 3 times (T3) when the AUTO hazard warning lamp switch is
pressed for less than 0.6 seconds (T1). A. Operation 1.
The hazard warning lamp comes on 10 times (T4) when the AUTO hazard warning lamp switch is
pressed for 0.6 seconds or more (T2).
The turn signal lamp switch is pressed during the AUTO hazard warning lamp operation.
The corresponding turn signal lamp is activated after this AUTO hazard warning lamp operation. B.
C.
D. Operation 2.
The AUTO hazard warning lamp can be controlled only with IGN ON.
The input from the AUTO hazard warning lamp switch is ignored during the turn signal lamp
operation by the turn signal lamp switch.
Priority of operation: (Hazard warning lamp switch > LH/RH turn signal lamp > AUTO hazard
warning lamp switch) -
-
-
Operating process

8710-01

Emergency hazard warning lamp control (coupled with ABS)
The emergency stop signal is input from the ABS/ESP module with the vehicle driven at 50 km/h or
more.
The hazard warning lamp flashes at 4 Hz (T1) and internal buzzer (chime) sounds at 1.25 Hz. A.
B. Operation 1. (emergency stop signal)
During operation 1 (emergency stop signal activated)
The vehicle speed decreased to 50 km/h or less
The hazard warning lamp flashes for 10 seconds (T2) at 1.25 Hz and then goes out. C.
D.
E.
The BCM activates emergency hazard warning lamp operation when receiving emergency braking
signal from the ESP/ABS.
Priority of operation
(Manual operation of hazard warning lamp > Emergency stop signal > Emergency AUTO hazard
warning lamp > AUTO hazard warning lamp) -
lamp)
During operation 2 (emergency AUTO hazard warning lamp)
The hazard warning lamp switch is turned OFF.
The hazard warning lamp is turned OFF because the manual operation overrides the emergency
AUTO operation. F.
G.
H.
The emergency stop signal and emergency AUTO hazard warning lamp signal are switched off
when the vehicle speed exceeds 10 km/h (if emergency stop signal is input).