2013 SSANGYONG KORANDO Service Manual

8910-05
To register Bluetooth device
Press the [Call] button for more than 3 seconds.
- "PAIRING" is displayed and followed by "KEY 00xx" to indicate stand-by mode. 1.
To set Bluetooth mode
When pressing the [SET] button, "Setup List" is displayed.
- The setting screen is displayed for 5 seconds. 1.
Making phone call using recent call list
When you [Call] button for more than 3 seconds, the system displays "REDIAL" and makes a phone
call to the recent calling party. 1.Activate the Bluetooth device to register to carry out Bluetooth setting/device search and connect it to
the audio system.
- If the searched device selection item is displayed, carry out selecting/connecting
"SSANGYONG".
- If the device search fails for 60 seconds, "NO device paired" is displayed. If this is the case,
carry out steps 1~2 above again. 2.
Enter the pairing key, "00xx", displayed on the audio system screen to the *pin code input item
of the Bluetooth device to connect and register it.
- When the registration is completed normally, the audio system screen displays "BT CONNECT"
and displays cellular phone model name or "BT MOBILE" together with the Bluetooth icon.
- The Bluetooth device can be registered just once. Although several devices can be
registered, you can select only 1 device to connect the system. If the registered Bluetooth
device is set to connect to other device, disable the previous connection under Connect
Bluetooth device and select "Car audio" or "Audio device" to connect the device to the system. 3.
Check whether the Bluetooth connection is completed. 4.
Turn the [TUNE] dial to select a desired "Bluetooth Setup" and press the [ENTER] button. 2.
Turn the [TUNE] dial to select a desired Bluetooth setup item and press the [ENTER] button.
For "Pair Device", see the steps 2~4 in "To register Bluetooth device". 3.
Turn the [TUNE] dial to select the device list and press the [ENTER] button.
- Select Device: Select the connected device.
- Delete Device: Delete the registered device.
- Priority Device: Set the connection priority for Bluetooth devices. 4.
9. BLUETOOTH

Answering an incoming call
When the call is incoming, the bell rings and "CALL IN" and sender's telephone number are
displayed. -
Hang-up call
To hang-up the call, press the [END] button.
- The call is ended and system returns to the previous screen.
- However, the connection between the audio system and the phone remains "connected". 1.To make a call, press the [Call] button.
- "BT TEL" is displayed during a call and you can converse through the microphone and
speaker connected to this system. If you don't want to receive a call, press the [End] button
to reject it.
- After "CALL REJECT" is displayed, the system returns to the previous screen. 1.
To adjust volume
Turn the [VOL] dial to adjust the volume.
- The adjustable range is between BT VOL 06 to 32. 1.
Mute function
Press the [MUTE] button on the audio remote control to activate the mute function.
- "MIC MUTE" is displayed and the other party can't hear your voice.
- Press the [MUTE] button again to resume your conversation. 1.
Private mode
When you press the [Call] button during hands-free call, "PRIVATE" is displayed and hands-free call
is changed to cellular phone call. When you press the [Call] button during cellular phone call, "BT
TEL" is displayed and cellular phone call is changed to hands-free call.
- This function may not be available on some phone models. 1.You can change to private call using a cellular phone during hands-free call. (The other party's voice
is coming through only the cellular phone, not speaker.) -
To disconnect
Press and hold the [End] button to disconnect the connection with Bluetooth device and press and
hold it once again to turn off the Bluetooth function.
- At this time, "BT DISCONNECT" is displayed and the Bluetooth icon disappears. 1.
Playing music stored in cellular phone
Press the [MEDIA] button repeatedly to select "BT AUDIO".
After playing the music using a music-playback function in the cellular phone, turn the [VOL] dial to
adjust the volume.
To exit the function, press the [End] button or press the [BAND/AS], [MEDIA] or CD button to select
other function. 1.
2.
3.

8910-05
* Connect iPod to USB terminal
- Playing music file in USB memory
- Playing external audio device
through AUX jack
- Supports iPod function
To playback USB/iPod
Press and hold the power button to turn the audio off.
Insert the linking cable of the USB or iPod in which MP3/WMA file to play is stored to the USB
terminal.
Press the [MEDIA] button repeatedly to select the USB or iPod function.
- "USB" or "I-POD" is displayed and the music files which has been played previously are
played automatically. 1.
2.
3.
To use AUX jack
Turn off the external device's power supply and connect its sound output to the [AUX] jack.
Press the [MEDIA] button repeatedly and select the [AUX IN] function.
Turn the [VOL] dial to adjust the sound volume. 1.
2.
3.
10. EXTERNAL DEVICE (USB/AUX & I-POD)
Layout with USB/iPod
USB 2.0 cable

Ensure that the connection or disconnection between the audio system and the USB memory/iPod
is carried out only when the engine is switched off. If the engine is switched on or off while the USB
memory is connected or disconnected, the USB memory may be damaged or not operate normally.
The audio system may not recognize some USB memory depending on the comparability or
condition. Check whether the USB memory operates normally in the vehicle before using it.
Take great care to ensure that the USB connection does not come in contact with the human body
or any object and the USB linking cable does not disturb a safe driving.
When you connect and disconnect the USB memory to the audio system several times in a short
periods, it may cause the USB memory to corrupt. If you particularly disconnect USB memory
during playback, it may be broken or operate incorrectly.
When you use the USB device for charging or heating by using the USB terminal on the audio
system, it may cause the system to deteriorate or fail.
iPod is a registered trademark of Apple Inc.
This audio system supports only the following iPod products: iPod Nano /iPod/iPod Touch/ iPhone.
This audio system may not support some iPod/iPhone products.
Always use the linking cable included with the iPod product when connecting it to the audio system.
The other cables may not be compatible and cause the audio system to fail.
In some cases, the iPod product may be damaged or not operate normally when the engine is
switched on while it is connected to the audio system. When not in use, always disconnect the iPod
product with the engine switched off.
When you use the iPod by connecting it to the audio system, the playback function and information
display may differ from original.
The iPod product can't be recharged using a iPod linking cable. -
-
-
-
-
-
-
-
-
-
-
-Cautions for using USB memory/iPod

0000-00
Wheel assembly changed
Wheel Assembly
Old
16-inch Silver 17-inch Silver 18-inch Hyper silver
PN: 41730-34000 PN: 41730-34100 PN: 41730-34220
New
16-inch Silver 17-inch Silver 18-inch Diamond cutting
PN: 41730-34200 PN: 41730-34300 PN: 41730-34400
- 16, 17 and 18-inch wheel assembly design changed
(For 17-inch: existing 18-inch design used)
- Wheel offset and tire size same as before
1. MAJOR CHANGES

Newly added TPMS (Tire Pressure Monitoring System)
TPMS related warning lamp
TPMS warning lamp Global warning lamp
- TPMS warning lamp: Comes on if an error occurs in any component
related to the TPMS regardless of tire inflation pressure.
- Global warning lamp: Comes on when the tire pressure is low.
DOT LCD display window (supervision
type)
Displays current tire pressure and
abnormality.

0000-00
Wheel module
The wheel modules are mounted to each wheel rim and hole. They transmit
the signal of the pressure and temperature in tire, rotating direction and
wheel module ID code, etc. using the radio frequency to the TPMS ECU.
TPMS ECU
The TPMS ECU is located to the rear bumper rail under the vehicle. It outputs the tire pressure
information and CAN data.

HECU (Hydraulic & Electronic Control Unit)
HECU for ABS HECU for EPS
The HECU (Hydraulic & Electronic Control Unit) determines the slip conditions of vehicle wheels by
calculating each wheel's speed and the increment/decrement of speed based on the information
detected by the sensors, and controls the pumping and boosting/reducing/keeping pressure by
operating the valve and motor of HECU.
2. MOUNTING LOCATIONS (CHASSIS)
Moto
HU (Hydraulic Unit) ECU (Electronic
Control Unit) Moto
HU
(Hydraulic Unit) ECU (Electronic
Control Unit)
Motor
angle (8P)
Motor power (3P)Torque angle
sensor (8P) Battery (2P) Connector to
vehicle (8P)
Fuse for EPS
Steering wheel angle sensor (SWAS)
The steering wheel angle sensor is mounted between the
steering column and the steering column shaft. It is
commonly used by the ESP (Electronic Stability Program)
system. And it receives signals of the steering wheel angle
sensor from the ESP HECU (Hydraulic & Electronic
Control Unit).
EPS unit
The ECU controls the electric power steering
system depending on the driving conditions,
based on the signals from the torque and
angle sensor.
E-coupling unit
The E-coupling unit is a control unit
which determines the magnetic force by
considering CAN signals (wheel speed,
engine torque, pedal opening, ABS/ESP
CAN signals, etc.) from other ECUs.