2011 Lexus CT200h Owner's Manual (in English)

5
601
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
Taking out the emergency tire puncture repair kit
Remove the center deck board.
Emergency tire puncture repair kit components
Insertion keyPower plug
Hose
Stickers
Air release
Compres-
sor switch Air pressureBottle
STEP1

602
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)Remove the center auxiliary
box.
Take out the emergency tire
puncture repair kit.
Taking out the jack
Remove the center deck board and center auxiliary box.
(See “Taking out the emergency tire puncture repair kit” for
details.)
Remove the hook and then
loosen and take out the jack.
For loosening
For tightening
When storing the jack, put it
into the tray and tighten it until
fixed to the tray.
Use of the jack: P. 5 8 9
STEP2
STEP3
STEP1
STEP2

5
603
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
Before performing emergency repair
Check the degree of the tire damage.
A tire should only be repaired
with the emergency tire punc-
ture repair kit if the damage is
caused by a nail or screw pass-
ing through the tire tread.
• Do not remove the nail or
screw from the tire. Remov-
ing the object may widen the
opening and disenable emer-
gency repair with the kit.
• To avoid sealant leakage,
move the vehicle until the
area of the puncture, if
known, is positioned at the
top of the tire.

604
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Emergency repair method
Pull the insertion key out of the
kit.
Place the kit with the bottom
facing upward.
Peel off the label, and push in
the insertion key until a click is
heard.
Return the kit to an upright
position and make sure that the
compressor switch is off.
Use the kit with the top facing
upward.
Connect the power plug to the
power outlet socket. (P. 451)
STEP1
STEP2
STEP3
STEP4

5
605
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)Remove the valve cap from the
valve of the punctured tire.
Remove the air release cap
from the hose.
Connect the hose to the valve.
Screw the end of the hose
clockwise as far as possible.
Check the specified tire infla-
tion pressure.
Tire inflation pressure is speci-
fied on the label as shown. (P.
649)
Start the hybrid system. (P. 196)
STEP5
STEP6
STEP7
STEP8
STEP9

606
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)To inject the sealant and inflate
the tire, turn the compressor
switch on.
Use the kit with the top facing
upward.
Inflate the tire until the recom-
mended pressure is reached.
The sealant will be injected
and the pressure will spike
to 300 kPa (3.0 kgf/cm
2
or bar, 44 psi) or 400 kPa
(4.0 kgf/cm2 or bar, 58 psi),
then gradually decrease.
The air pressure gauge will
display the actual tire infla-
tion pressure about 1 minute
after the switch is turned on.
• Turn the compressor switch
off and then check the tire
inflation pressure. Being
careful not to over inflate,
check and repeat the infla-
tion procedure until the rec-
ommended tire inflation
pressure is reached.
STEP10
STEP 11

5
607
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
• If the needle of the air pres-
sure gauge reaches the red
zone (450 kPa [4.5 kgf/cm
2
or bar, 65 psi] or more),
there may be a malfunction
in the tire or in the kit itself.
Stop operation immediately.
• If the tire inflation pressure
is still lower than the recom-
mended level after inflation
for 10 minutes with the
switch on, the tire is too
damaged to be repaired.
Turn the compressor switch
off and contact any autho-
rized Lexus dealer or
repairer, or another duly
qualified and equipped pro-
fessional.
• If the tire inflation pressure
exceeds the recommended
level, let out some air to
adjust the tire inflation pres-
sure.
(P. 6 1 1 )
Disconnect the hose from the valve on the tire and then pull
out the power plug from the power outlet socket.
To spread the liquid sealant evenly within the tire, immedi-
ately drive for about 5 km (3 miles).STEP 12
STEP 13

608
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)After driving for about 5 km
(3 miles), stop your vehicle in a
safe place on a hard, flat surface
and reconnect the compressor.
Turn the compressor switch on
and wait for several seconds,
then turn it off. Check the tire
inflation pressure.
If the tire inflation pressure is
below 130 kPa (1.3 kgf/cm
2
or bar, 19 psi): The puncture
cannot be repaired. Contact
any authorized Lexus dealer
or repairer, or another duly
qualified and equipped pro-
fessional.
If the tire inflation pressure is
between 130 kPa (1.3 kgf/
cm
2 or bar, 19 psi) and a
point below the recom-
mended level: The tire can be
repaired. Proceed to .
If the tire inflation pressure is
at the recommended level:
Proceed to .
STEP 14
STEP 15
STEP 16
STEP 17