2008 GEELY MK Workshop Manual

Chapter 17 Moonroof Assembly (Optional)Component ViewII. Inspection of sunroof Troubleshooting formSunshade sub-assy Sunroof motorBracket sub-assy.Sunroof frameSunroof glass bracketSunroof glass sealSunroof glassInterior & Exterior Trim and Accessory -Moonroof Assembly (Optional)6-40Possible causes
1. Power relay
2. Instrument fuse
3. Sunroof switch
4. Sunroof lock switch
5. Sunroof motor
6. Sunroof guide rail
7. Wire harness
1. Sunroof lock switch
2. Sunroof motor
3. Sunroof guide rail
4. Wire harnessSymptom
Sliding sunroof system doesn't work.
Sling sunroof system gets stuck (e.g.
foreign matter like gravel caught in motor)

Interior & Exterior Trim and Accessory -Moonroof Assembly (Optional)6-41III. Removal and installation of sliding sunroof1. Remove the roof panel trim
(For more information, see "removal and installation of roof panel trim".)
2. Remove the ceiling lamp
(For more information, see "removal and installation of roof panel trim".)
3. Remove the sunroof glass sub-assembly
a. Unfix the screw by use of a box spanner;
b. Pull the glass upward and then take it out.
4. Remove the sunroof motor
Caution
Make sure the sunroof is completely closed before removing the sunroof motor.
a. Disconnect the connector;
b. Unfix the bolt and then remove the sunroof motor.
5. Remove the sunroof bracket sub-assembly
a. Detach water pipe;
b. Unfasten the retaining bolts around the sunroof bracket sub-assembly;
c. Take out the sunroof bracket sub-assembly.
6. Remove the sunshade sub-assembly
Slide the sunshade backward and then take it out.
7. Remove the sunroof drive cable and the sunroof guide rail;
8. Install in reverse order of removal.
Caution
Check if the sunroof is waterproof after installation.
If a water leak is detected, readjust the sunroof.
For more information on the electrical part of sunroof, see the chapter on electrical part of this manual.

1 1018005004 Side Dash25.5 2
2 1018005000 Front floor13.5 4
3 1018005001 Front floor and rear floor 44.5 6
4 1018005003 Front floor30.5 2
5 1018005002 Front floor 2
6 1018005005 Rear floor 2
7 1018005006 Side dash11 2
8 1108005007 Positioning plate for taillight9.5 2
9 1018005008 Front floor9.5 4
10 1018005009 B-pillar17 2
11 1018005010 B-pillar25 4
12 1018005011 Front of Side dash20 2Chapter 18 Plug ListNo. Picture Material code Position Diameter QuantityInterior & Exterior Trim and Accessory -Plug List6-42

Interior & Exterior Trim and Accessory -Plug List6-4313 1018005012 Under the Side dash outer plate21.5 18
14 1018005013B-pillar¡¡15 2
15 1018005014 C-pillar40 6
16 1018005015 Doorsill30 6
17 1018005016 Top cover60 4 No. PictureMaterial codePosition Diameter Quantity

Part VII BodyChapter 1 SurveySection 1 Body StructureThe body is made up of main structure, movable plate work, interior/exterior trim parts, and body accessories.I. Main StructureAs shown in Fig.5-1, the main structure is made up of various assemblies and parts including engine compartment
assembly & front wall parts, floor assembly, left/right wall assembly, rear wall assembly, roof assembly and
luggage compartment main cover assembly etc.Fig. 5-1 Main Structure
1 Engine compartment assembly & front wall parts 2. Left/right wall assembly
3. Luggage compartment main cover assembly 4. Rear wall assembly 5. Floor assembly
6. Roof assembly 7. Front cross beam assembly(1) Engine Compartment Assembly & Front Wall Parts The main function of the engine compartment assembly and front wall parts is to form an engine compartment
and absorb most energy generated when the vehicle is collided from the front. The compartment provides a hood
for the engine and its accessories, which can prevent the front wheel from throwing mud. In the appearance, it
represents the body's design requirements. As shown in Fig.5-2, the engine compartment assembly and front wall
parts include front cross beam assembly, left/right longitudinal beam assembly, radiator cross beam assembly,Body -Survey7-1
123456
7

1. Front cross beam assembly
The front cross beam assembly includes front cross beam left/right support assembly, front cross beam sub-
assembly, front cross beam side support etc. They play a role in front bumper.
2. Left/right longitudinal beam assembly
The left/right longitudinal beam assembly includes left/right longitudinal bean front and mid- block assembly,
energy-absorbing beam big assembly, and left/right front damper support assembly etc.
It is mainly used to install engine left/right suspension, left/right front suspension damper, storage battery and
other accessories. In the outside, it can be equipped with left/right front fender.
3. Radiator cross beam assembly
The radiator cross beam assembly includes radiator left/right post big assembly, radiator lower cross beam big
assembly, radiator central support sub-assembly, and radiator upper cross beam big assembly etc.
It is mainly used to install radiator, condenser, engine hood lock, radiator hood, front bumper, and front
headlight.
4. Front wall lower plate assembly
The front wall lower plate connects to the floor, which separates the engine compartment from the cabin. It
includes front wall frame assembly, front wall lower main plate assembly, brake installation reinforced plate, and
front wall left/right support assembly etc.Fig. 5-2 Engine Compartment Assembly & Front Wall Parts
1. Front cross beam assembly 2. Left/right longitudinal beam assembly
3. Panel left/right support assembly 4. Front wall lower plate sub-assembly 5. Front wall upper assembly
6 Radiator cross beam assemblySurvey -Body Structure7-2123456front wall lower plate assembly, front wall upper assembly, left/right front damper support lower front plate
assembly, and right front damper right-angle support assembly.

It is mainly used to install the pipes and accessories of the brake system and clutch system.
5. Front wall upper assembly
The front wall upper assembly includes left/right hinge base mounting plate big assembly, front wall upper
front cover big assembly, VIN number mounting plate, and front wall upper rear cover big assembly etc.
It forms a high-stiffness frame structure together with the engine compartment assembly and the front wall
lower plate assembly. It can generate strong resistant to the transverse collision and rolling deformation. It can also
separate the engine compartment form the cabin, preventing the odor entering into the cabin. Consequently, it can
isolate the noise, heat and vibration.(2) Floor Assembly The floor assembly is the base work of the main structure. It is a key component that connects various
assemblies and carries the load. The vehicle performance is subject to its strength and stiffness. For the floor
assembly, see the Fig. 5-3.
The floor assembly includes front floor assembly and rear floor assembly. The front floor mid-block goes
through a ridgy channel in longitudinal direction. It can increase the longitudinal rigidity together with the lower
floor longitudinal beam. The space below under the channel is used to install various parts and components, such
as transmission gearshift rod, parking brake cable, discharge pipe with three-way catalytic converter etc. In the
cabin, there is carpet and muffle pad. The floor frame structure is made up of front floor left/right frame, front floor
main plate assembly, front floor mid-bridge assembly, rear frame assembly, rear floor rear block assembly, rear
floor mid-block assembly and longitudinal beam etc. These parts and components provide strong and reliable carry
capacity and ensure that the vehicle meets the strict driving requirement on the body.Fig. 5-3 Floor Assembly
1. Front floor left/right frame 2. Front floor main plate assembly 3. Longitudinal beam rear block 4. Rear frame assembly
5. Rear floor rear block assembly 6. Rear floor mid-block assembly 7. Front floor mid-bridge assemblySurvey -Body Structure7-371
2
133
5
6

(3) Side Wall Assembly The left/right side wall assembly is a frame structure, which is a side component that connects the front and
rear parts of the body. As shown in Fig.5-4, it includes left/right side wall outside plate assembly, left/right wheel
assembly, left/right A post inside plate assembly, and left/right intermediate post interior plate assembly etc.Survey -Body Structure7-4Fig. 5-4 Side Wall Assembly
1. LH/RH upper front body inner pillar 2.LH/RH lower front body inner pillar 3.LH/RH no.1 crossemember joint panel
4.LH/RH roof inner rail 5.LH/RH center body inner pillar 6.LH/RH rear crossmember tee joint panel
7.LH/RH lower rear pillar remforcement panel 8.LH/RH roof rear inner panel 9.LH/RH side rear pillar inner panel
10.LH/RH luggage compartment support panel 11.LH/RH luggage compartment hinge fixing panel
12.LH/RH wheel house outer panel 13.LH/RH wheel house inner panel 14.LH/RH side panel
15.LH/RH rear combination lamp fixing panel 16.Fuel refilling cap assembly 17.LH/RH side doorsill outer reinforcement panel
18.LH/RH side doorsill inner reinforcement panel 19.LH/RH center pillar upper reinforcement panel
20.LH/RH front seat belt upper reinforcement panel 21.LH/RH roof rail upper master reinforcement panel
22.LH/RH center pillar middle reinforcement panel 23.LH/RH center pillar lower reinforcement panel
24.LH/RH roof rail assistant reinforcement panel 25.LH/RH front body pillar upper reinforcement panel
26.LH/RH front body pillar outer reinforcement panel