2008 GEELY MK Workshop Manual

Check1. Check the brake booster.
(1) Air tightness check
a. Start the motor, and shut it down after one or two minutes,
then step on the pedal several times slowly.
Tips:
If the pedal goes down greatly at the first step, but it gradually
goes up after the second and third steps, it means the air
tightness is good.Brake System -Vacuum Booster4-92 b. When the motor is running, step down the brake pedal, and then shut down the motor.
Tips:
If the reserved distance does not change thirty seconds after
the pedal is stepped down, it means the air tightness is good.
(2) Operation check
a. When the ignition switch stays in OFF position, step on the
pedal several times, and then check that the reserved
distance should not change.
b. Step down the pedal, and start the motor.
Tips:
If the pedal goes down a little, it means the operation is ok.
2. Check the vacuum one-way valve.
(1) Check the vacuum one-way valve.
a. Slide the clip to unfix the vacuum tube.
b. Remove the vacuum one-way valve.
c. Check the booster is ventilated to the motor.
d. In case of any failure, replace the vacuum one-way valve.ONOFFPositiom 1Positiom 2Positiom 3 Good Poor

Brake System -Vacuum Booster4-93Replacement1. Discharge the brake fluid.
Note:
Never spray the brake fluid on the paint surface, otherwise wash it immediately.
2. Unfix the clutch fluid tank pipe (manual transaxle).
3. Remove the brake master cylinder.
4. Remove the HECU assembly (with ABS).
5. Remove the vacuum booster.
(1) Unfix the vacuum tube from the brake booster.
(2) Remove the return spring, clip and pin.
(3) Remove the four nuts and U-clip.
(4) Pull out the vacuum booster and washer.
6. Install the vacuum booster.
(1) Install the vacuum booster and new washer.
(2) Install and fasten the vacuum booster nut.
Torque: 25N.m
(3) Install the return spring, clip and pin.
7. Install the vacuum booster push bar.
8. Install the brake actuator. (with ABS)
9. Install the brake master cylinder.
10. Connect the clutch fluid pipe.
11. Add the brake fluid to the reservoir.
12. Discharge the air in the brake master cylinder.
13. Discharge the air in the brake pipeline.
14. Check and adjust the height of the brake pedal.
15. Check the free stroke of the pedal.
16. Check the reserved distance of the pedal.
17. Discharge the air in the clutch tank pipe (manual transmission).
18. Check and adjust the clutch pedal (manual transmission).
19. Check the level height in the brake reservoir.
20. Check the brake fluid whether there is any leakage.
21. Check the clutch fluid whether there is any leakage (manual transmission).

Brake System -Front Brake Disc4-94Component ViewSection 6 Front Brake Disc34Front disc brake pistonSet ring Dust shield Piston oil seal Left front disc
brake cylinder accessory3483088Connector bolt
Washer
Discharge screw
plug capTubeDust shield Front disc brake
cylinder sliding pin
#2 muffle pad
#1 muffle pad
Brake pad
Brake pad#1 muffle pad
#2 muffle pad
Support piece
Front brake pad ISupport piece
Front brake pad IIFront disc brake cylinder
sliding pin88Dust shield
Left cylinder support
Non-reusable parts
Lithium soap base glycol lube
Disc brake lubespecified torqueN.
m :

Repair1. Remove the front wheel.
2. Discharge the brake fluid.
Note:
Never spray the brake fluid on the paint surface, otherwise wash it immediately.Brake System -Front Brake Disc4-95Sliding Pin Dust Shields3. Remove the front disc brake cylinder.
(1) Remove the connector bolt and washer from the front disc
bake cylinder, and unfix the tube.
(2) Fasten the sliding pin on the front disc brake cylinder, and
remove the two bolts.
4. Remove the front brake pad package (only the pad).
(1) Remove the two brake pads with muffle washers.
(2) Remove muffle and heat isolation washers from the brake
pads.
5. Remove the support pad of the front brake pad.
Remove the two friction block from the brake cylinder support.
6. Remove the sliding pin of the front disc brake cylinder.
7. Remove the two dust shields
Remove the two dust shields from brake cylinder support.
8. Remove the left front disc brake cylinder support.
Remove the two bolts, and then take out the left front disc brake
cylinder support.
9. Remove the dust shield of the brake cylinder.
Remove the retaining ring and dust shield with screwdriver.Braking Disc Cylinder Bracket

Brake System -Front Brake Disc4-9611. Remove the front brake piston.
(1) Put a piece of cloth or equivalent between the brake cylinder
and the piston.
(2) Blow the piston out of the brake cylinder with compressed air.
Warning:
In the blowing process, the finger shall not be placed before the
piston.
Note:
Don't spray the brake fluid.
12. Remove the piston oil seal.
Take out the oil seal from the brake cylinder with screwdriver.
13. Check the brake cylinder and piston.
Check the cylinder wall and piston whether there is rust or scar.
14. Check the lining thickness of the brake pad.
Measure the lining thickness with ruler.
Standard Thickness: 10.0mm
Minimum Thickness:1.0mm
15. Check the abrasion indicator steel strap of the front brake.
Make sure the abrasion indicator steel strap has adequate flexibility and has no deformation, crack or damage.
All rust, dirt and other impurities shall be cleaned out.
16. Check the thickness of the brake disc.
Measure the thickness of the brake disc with screw micrometer.
Standard Thickness: 20.0mm
Minimum Thickness: 18.0mm
17. Remove the front brake disc.
(1) Make mark on the brake disc and wheel hub.
(2) Remove the brake disc.
18. Install the brake disc.
Tips:
Install the disc at the minimum swing position.

Brake System -Front Brake Disc4-9719. Check the swing of the brake disc.
(1) Fasten the brake disc temporarily.
Torque: 103N.m
(2) Measure the swing of the brake disc at the 10mm from the disc
edge with a dial test indicator.
Maximum Swing: 0.05 mm
(3) If the swing of the brake disc reaches or exceeds the limit,
check the bearing's axial clearance and the wheel hub's swing.
If the bearing and wheel hub run normally, adjust the swing
of the brake disc, or finish it with onboard finishing machine.
20. Tighten the brake discharge bolt temporarily.
Tighten the brake discharge screw plug on the front brake cylinder temporarily.
21. Install the piston oil seal.
(1) Apply the lithium soap-base glycol lube on the new piston oil seal.
(2) Install the new piston oil seal on the brake cylinder.
22. Install the brake piston.
(1) Apply the lithium soap-base glycol lube on the brake piston.
(2) Install the piston on the front disc brake cylinder.
Note:
Don't tighten the piston into the brake cylinder forcefully.
23. Install the dust shield of the brake wheel cylinder.
(1) Apply the lithium soap-base glycol lube on the dust shield of
the new brake wheel cylinder, and install it on the brake
cylinder.
Tips:
Install the dust shield in the groove of the brake wheel cylinder
and piston reliably.
(2) Install the set ring with screwdriver.
Note:
Be careful not to damage to the dust shield of the brake wheel cylinder.
24. Install the left front disc brake wheel cylinder support.
Fasten the front disc brake wheel cylinder support with two blots.
Torque: 88N.m
25. Install the dust shield of the front disc brake bushing.
Apply the lithium soap-base glycol lube on the surface of the two new dust shields.
Install the two dust shields on the front disc brake cylinder support.
26. Install the sliding pin of the front dist brake cylinder.
Apply the lithium soap-base glycol lube on the surface of the two sliding pin and oil seal.
Install the two sliding pins on the front disc brake cylinder support.

Brake System -Front Brake Disc4-9827. Install the support piece of the front brake pad.
Remove the two support pieces of the brake pad from the front disc brake cylinder support.
28. Install the brake lining block component.
Note:
When replace the abrasion brake lining block, replace the muffle
pad simultaneously.
(1) Apply the disc brake lube on both sides of all muffle pads
(2) Install muffle pads on all brake lining blocks.
(3) The abrasion indicator face upwards. Install a inner brake
lining block, then install a outer lining block.
Note:
Don't apply the oil or lube on the friction surface of the brake pad and brake disc.
29. Install the front disc brake wheel cylinder.
(1) Install the front disc brake wheel cylinder with two bolts.
Torque: 34N.m
(2) Install the new washer and tube with bolt.
Torque: 30N.m
Tips: Fasten the tube in the lock hole of the brake wheel
cylinder reliably.
30. Add the brake fluid to the storage tank.
31. Discharge the air in the brake cylinder.
32. Discharge the air in the brake pipeline.
33. Check the level height in the storage tank.
34. Check the brake fluid whether there is any leakage.
35. Install the front wheel.
Torque: 103N.m

Section 7 Rear Brake DrumComponent ViewDust shield
Piston
Cup
Spring
Rear bake shoe
Locating spring
Rear brake drum Shoe pad positioning spring cover Front brake shoe
Shoe pad positioning spring cover Pin
BaseboardDust
coverPiston
PinCupLeft parking brake shoe pad postCvlinder
Extension springBrake System -Rear Brake Drum4-99Discharge plug
Discharge plug
Hole plug
Pin plug
C-ringExtension rod
Shoe pad positioning spring Adjustment rod springRear brake automatic
adjustment rodParking brake
inhaul cable
Return spring
Non-reusable parts
Lithium soap base glycol lube
Heat-resistant lubespecified torqueN.
m :