2008 GEELY MK alarm

Repair1. Discharge the brake fluid.
Note: Never spray the brake fluid on the paint surface, otherwise
wash it immediately.
2. Remove the brake master cylinder.
(1) Pull out the connector of the level alarm light switch.
(2) Slide the clip, and pull out #1 clutch storage tank pipe (manual
transaxle).
(3) Remove the two brake pipes from the brake master cylinder
with special tool.(with ABS)
(4) Remove the three brake pipes from the brake master cylinder
accessory with special tool. (without ABS)
(5) Remove the two lock nuts, and pull out the brake master
pump.
3. Remove the storage tank.
(1) Put the brake master cylinder on the bench clamp.
(2) Remove the pin from the brake master cylinder body with
punch and hammer.
(3) Pull out the Brake fluid reservoir.
(4) Remove the cover and strainer from the storage tank.
(5) Remove the storage tank and the two hole connectors.
4. Remove the brake master cylinder.
(1) Put the brake master cylinder on the bench clamp.
(2) Remove the O-ring.
(3) Push the piston with hand, and remove the snap ring with
snap ring pliers.Brake System -Brake Master Cylinder Assembly4-87With ABS:
Without ABS

Brake System -Brake Master Cylinder Assembly4-90 (4) Adjust the length of the vacuum booster push bar with the
special tool till the push bar touches the mandril head.
9. Install the brake master cylinder.
(1) Install the brake master cylinder on the booster with two bolts.
Torque: 13N.m
(2) Connect the two brake oil pipes to the brake master cylinder
with a special tool. (with ABS)
Torque: 15N.m
(3) Connect the three brake oil pipes to the brake master cylinder
with a special tool. (without ABS)
Torque: 15N.m
(4) Connect # 1 clutch storage tank oil pipe with clip. (Manual
transaxle type)
(5) Insert the brake fluid level alarm switch connector.
10. Add the brake fluid to the Brake fluid reservoir.
11. Discharge the air in the brake master cylinder.
12. Discharge the air in the brake pipeline.
13. Check the level height in the Brake fluid reservoir.
14. Check the brake fluid whether there is any leakage.With ABS:
Without ABS

Note:
To measure, disconnect the connector.
5. Check water thermometer
(1) Check resistance
When water thermometer indicates water temperature to red area, check the resistance between C24
terminal and C13 terminal on combination instrument connector.
Standard 4. Check fuel gauge
(1) Check resistance
Check resistance between C21 terminal and C13 terminal on combination instrument connector.
Standard:5-19Standard indication
E
Reminder point
1/2F
FResistance (ohm)
104-116
90-100
29-35
1-5
Standard indication
C
1/2H
Alarm point
HResistance (ohm)
159. 5-169. 5
53-59
26. 7-30. 7
20-24
Note:
To measure, disconnect the connector.
6. Check water temperature warning lamp
(1) Disconnect water temperature sensor connector.
(2) Turn ignition switch to ON, water temperature warning lamp should go out.
(3) Ground instrument connector C24 terminal, water temperature warning lamp should illuminate.
7. Check engine oil pressure warning lamp
Disconnect engine oil pressure transducer connector.
Turn ignition switch to ON, engine oil pressure warning lamp should go out.
Use conductor to short connector terminal to earth, engine oil low pressure warning light should illuminate.
8. Check engine oil pressure transducer
Disconnect connector from engine oil pressure transducer
Check connection between terminal and ground
Engine stall: on state
Engine running: off state.Combination Instrument System -Malfunction Symptom Table and Troubleshooting

4. Danger alarm lamp switch assembly
Check whether danger alarm lamp switch is connected.
Check whether two terminals are connected when switch works.
If it doest not meet stipulation, replace the switch.
5. Door lamp switch (on fastener)
Check whether door lamp switch is connected
When switch works, check whether connection is established
between terminal and bodywork earthing.
If it doest not meet stipulation, replace the switch.
6. Trunk lamp switch assembly
Check whether trunk lamp switch is connected
When switch works, check whether connection is established between terminal and bodywork earthing.
If it doest not meet stipulation, replace the switch.
7. Front reading light assembly (with power sunroof)
Check whether terminals of indoor roof lamp assembly are
connectedSwitch motion Testing terminal Status
ON 1-2 ON
OFF 1-2 OFFSwitch motion Testing terminal Status
ON (door is closed) 1- GND ON
OFF (door is not closed) 1- GND OFF
Switch motion Testing terminal Status
ON 1- GND ON
OFF 1- GND OFFSwitch motion Testing terminal Status
ON 1-2 ON
OFF 1-2 OFF If it does not meet stipulation, replace roof lamp or switch.
8. Rear reading light assembly
Check whether back row reading light assembly is connected
When switch works, check whether two terminals are connectedSwitch motion Testing terminal Status
ON 1- 2 ON
OFF 1- 2 OFF If it doest not meet stipulation, replace the switch.211Light System -Light System Malfunction Inspection5-33

IV. Post-defrost: 1. When engine speed exceeds 700rpm (ignition switch is turned on), defrost work is permitted.
2. Turn on defrost switch, perform defrost work for 12 minutes, if defrost switch is pressed down again during
defrost work, defrost work will stop.
3. During defrost, turn off ignition switch, cancel this defrost.V. Light control: 1. Headlight:
(1) After press remote lock key to close four doors, if remote lock key is pressed down again twice in
succession within in 2s, dipped headlight will extend lighting for 1 minute; if remote unlock key is
pressed down within 60s, dipped headlight control output will be turned off.
(2) During output of 60s low level, if ignition switch is turned on, low level output will stop.
2. Ceiling lamp:
(1) When any of the doors is opened, ceiling lamp illuminates; if door is not closed, ceiling lamp will be
turned off after 10 minutes of delay.
(2) For closing of all doors, ceiling lamp will go out after time delay of 30s;
(3) In case all doors are closed,and ceiling lamp illuminates,ignition switch is turned on,ceiling lamp goes
out.
(4) For remote unlock, ceiling lamp illuminates; in case all doors are closed and ceiling lamp illuminates,
remote lock ceiling lamp goes out.VI. Remote anti-theft 1. Protected state: press lock key on remote controller, while closing four doors, anti-theft indicator lamp will
flashes slowly, indicating that the system enters protected state, when the system is triggered, turn light of the
vehicle will flash, warning horn gives out alarm.
2. Cancel protection: press unlock key on remote controller, while opening left front door, anti-theft indicator
lamp flashes rapidly, if at least one of ignition switch, door is opened within 30 s, anti-theft indicator lamp will
go out; otherwise it will enter secondary anti-theft state.
3. Two stage type protection cancellation: while the system is in triggered state, press any key on the remote
controller, alarm sound will stop, however, the system is still in protected state, and car door is still locked; if the
system continues to receive invasion signal, alarm will ring again after brief stop. To cancel protection completely,
cancel alarm for the first time, then press unlock key once immediately;
4. Secondary anti-theft: after protection is cancelled, if any of ignition switch, door is not opened within 30s,
the system will restore alert status automatically, and lock the car door.
Distribution of centralized controller connector terminals:
Connector on wiring harness, as shown in the figure below (view from outgoing terminal):Centralized Controller System-
Function Inspectior5-134Centralized
controller

Chapter 3 Front Seat BeltSeat Belt Reminder SystemI. Component View
II. Fault diagnosis
Possible causes
1. GAUGE fuse;
2. Instrument cluster;
3. Left front buckle assembly
4. Wiring harnessSymptom
Driver's seat belt lamp is not onIII. Alarm system inspection
1. To inspect the left front buckle assembly
Check the conductivity of left front buckle assemblyTerminal Number Seat Belt Required
1<=>2Insert OFF
1<=>2Release ON If you find that the result of the inspection is not the same as
required, you can replace the left front buckle assembly.DriverÕs seat belt reminder lamp
Left front buckleInterior & Exterior Trim and Accessory
-Front Seat Belt6-5

Interior & Exterior Trim and Accessory -Front Seat Belt6-7Pulley coverUnlock
Lock Notes:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
4. Use screwdriver to pry open the seat belt pulley cover;
5. Unscrew the bolt and detach the seat belt ring from the car;
6. Disconnect the pre-load insertion of seat belt on the bottom edge
of the middle pillar;
7. Detach the front seat belt from the car;
8. Unfix the clip using the screwdriver and detach the trim from the
right middle pillar;
9.Unscrew two bolts using the spanner and detach the remote adjuster
assembly.
Notice:Only the ignition switch turns to "OFF" position and the battery negative should be disconncted more than
90s, the seat belt with pretensioner can be removed.
III. Seat belt with ELR and pre-tensioner
Seat belt with ELR and pre-tensioner is provided with pre-tensioner which works together with the airbag.
The pre-tensioner is part of airbag assembly. The pre-tensioner is mounted in the retractor and controlled by SDM.
When the front bumping force of the car exceeds a specific value, the pre-tensioner and airbag can be triggered
at the same time. To maintain the pre-tension type of seat belt (retractor), observe all the "Alarm" and
"Operation Instruction".
Warning:
Do not try to remove or repair seat belt pre-tensioner. If any abnormal situations take place, replace the whole
assembly with a new one.
Before working, be sure to read through "Attention for Maintenance", and observe them during working. Any
ignorance can cause injury or the failure of seat belt pre-tensioner.
IV. Inspect Operations of Seat Belt Alarm Lamp (on Driver's side)
1. Turn on the ignition switch and check if the seat belt alarm lamp flashes;
2. Fasten the belt buckle and check if the belt alarm lamp goes out;
3. Turn off the ignition switch;
4. Disconnect the seat belt buckle;
5. Turn on the ignition switch;
6. Connect wiring terminal and make earth connection, and inspect the lamp status of the seat belt. Seat belt lamp:
flashing.
V. Inspect Seat Belt
1. Confirm whether the seat belt is properly mounted.
2. Inspect whether the metal part of seat belt is damaged.
3. If the car vibrates in accidents, pull out the seat belt from the retractor and determine whether the seat belt is
scratched (load limit retractor does not work) by visual inspection and touching.
4.Inspection contents before outer seat belt instalation:When ELR
lock,check the gradient of ELR. Check and make sure the seat belt
can not be locked from any aspect within 15°.When you move the
belt ring device beyond 45° slowly,the seat belt should be locked.
5.After installation check the seat belt lock in this way that draw the
seat belt from belt ring quiekly and the seat belf can be locked
normally.
Attention:
Should the seat belt not comply with the technical specification,
you should replace it.