2008 GEELY MK Workshop Manual

Chapter 14 Outside Rearview Mirror................................................................................. 6-37
Chapter 15 Door Protecting Stripe.................................................................................... 6-38
Chapter 16 Carpet and Insulator....................................................................................... 6-39
Chapter 17 Moonroof Assembly (Optional)...................................................................... 6-40
Chapter 18 Plug List........................................................................................................... 6-42Part 7 BodyChapter 1 Survey................................................................................................................ 7-1
Section 1 Body Structure ................................................................................................ 7-1
Chapter 2 Body Repair....................................................................................................... 7-9
Section 1 Body Damage Forms and Requirements for Repair ...................................... 7-9
Section 2 Typical Technique of Body Panel Repair ....................................................... 7-16
Section 3 Repair After Body Damage ............................................................................ 7-16
Section 4 Features and Composition of Automobile Body ............................................ 7-24
Section 5 Painting Techniques After Body Repair ......................................................... 7-35
Section 6 Service Data For for Body .............................................................................. 7-36Attachment: Body Key Dimensions
Appendix: Torque Table of the Fasteners for Important AssemblyTable of Contents VI

General Information - How to Use This Manual1-1Part 1 General InformationChapter 1 How to Use This ManualI. Instruction1. General Information
(1)This manual conform to the first part of GB/T1.1--2000 Standardization Guide: The structure and prepar-
ing rule of the standard.
(2)Generally, the repairing job can be divided into the following 3 procedures:
1. Diagnosis
2. Removal and installation, replacement, disassembly and inspection, adjustment
3. Final inspection
(3) The first procedure “Diagnosis” (the details refers to each section or chapter) and second procedure “Re-
moval and installation, replacement, disassembly and inspection, adjustment” are scattered in the chapters and
sections, and this manual omits the third procedure “Final inspection”.
(4) This manual does not include the following basic operations which are imperative in real scenarios.
operate the jack or lifter
b. clean the removed parts if necessary.
c. inspect the appearance
2. Preparation
SST (Special Service Tools) and SSM (Special Service Materials) may be required and correctly used based
on the repairing condition, make sure the job procedure is followed.
3. Repair Procedure
(1) The disassembly illustration is placed under the title.
(2) The illustration shows the disassembly of the parts to help you understand the assembly of the parts. (3) Non-reusable parts need to be coated with grease, and the precoated parts and torque are specially shownin the disassembly illustration.
(4) Sometimes, the illustrations of the similar model are used where there may be some details differently
from the actual vehicle.
(5)The operational procedure is described in the following ways:
a. The illustration shows what to do and where to do it.
b. The task heading tells what to do.
c.The detailed text tells how to perform the task and gives other information such as specifications and
warnings.
4. Specification
Specifications are presented in bold type throughout the manual.
5.Term Definition
6. International System of Unit
The Units given in this manual are primarily expressed according to the International System of Unit.Caution indicates there is a possibility of injury to you or other people.
Notice indicates the possibility of damage to the components being repaired.
Tip provides additional information to help you perform the repair efficiently.a.

General Information - How to Use This Manual1-2II. Vehicle Identification1. Vehicle Identification Number
(VIN):
Vehicle Identification Number
(VIN) is the legal identification of the
vehicle which is printed on the middle
of the engine compartment cowl (as
shown in the illustration).VIN code position3. Ex-work Nameplate: on the middle of the engine
compartment cowl
4. VIN Code: on the left lower corner of the front windshield.
5. Engine Number:
marked on the engine block as shown in the illustration6. Transmission Mark:
printed on the left side of the transmission 2. VIN CodeMark positionMark position

General Information - Repair Instruction1-3Chapter 2 Repair InstructionI. Precautions1. Basic Repair Hint
(1)Operation HintVehicle Protection
Appearance
Safe Operation
Removal and
installation, disas-
semble and inspection
Prepare the tools and
measuring instrument
Removed partsBefore the work, place radiator fascia cloth, fender cloth, seat cover and mat.
Always wear clean uniform
Make sure to wear the helmet and safety shoe
when more than 2 persons work together, be sure to pay mutual attention to the safety.
when it is required to run the engine, you have to pay attention to the ventilation of the workshop.
When handling the high-temperature, rotating, moving and vibrating parts, be careful not to be scalded
or hurt.
When lifting the vehicle, safety stand should be used to support the specified position.
When lifting the vehicle, safety devices should be used.
The diagnosis requires full understanding of the trouble and effective operation.
Before the parts are removed, check the assembly for distortion and damage.
The diagnosis requires full understanding of the trouble and effective operation.
Before the parts are removed, check the assembly for distortion and damage.
If the structure is complicated, notes or marks should made to avoid mistake and impact of the part
function.
If needed, clean the removed parts and reassemble them after careful inspection.
Before the work, prepare the tool fixture, special tools, instrument, oil, workshop cloth and required
parts for replacement.
arrange the removed parts in correct sequence, do not confuse or contaminate them.
For non-reusable parts such as gasket, O ring and self-locking nut, replace them with new ones in
accordance with the instruction described in this manual.
Pick up replaced parts, put them in the containers, and show them to the customers.2
435 61

General Information - Repair Instruction1-4(2)Lift and support the vehicle
Be careful to lift and support the vehicle. Make sure that the vehicle is appropriately supported.
(3)Precoated Parts a. Precoated parts are bolts, nuts, etc. that are coated with a seal
lock adhesive at the factory. b. If a precoated part is retightened, loosened or caused to move
in any way, it must be recoated with the specified adhesive. c. When reusing precoated parts, clean off the old adhesive and
dry with compressed air. Then apply the specified sealing adhesive
to the bolt, nut or threads.Illustration Symbol Part Name
FuseMedium Current
Fuse
High Current Fuse Notice: the torque should achieve the lower limit of the allowed torque range.
d.The precoated parts should be kept intact for a period of time for induration based on the requirement of
the sealing adhesive.
(4)Gasket
If necessary, apply the sealant to the gasket to prevent disclosure.
(5)Bolt, nut and screw
Be careful to follow all torque specification and torque wrench should be used.
(6)Fuse
When replacing fuses, be sure the new fuse has the correct am-
perage rating. Do not exceed the rating or use one with a lower rating.Sealing Adhesive
Equal Rated Ampere Value

General Information - Repair Instruction1-5(7)Clip
The following illustration shows the typical removal and installation of the clip for body parts.
Tip:
If the clip is damaged during the operation, you have to replace it with a new one.
IllustrationRemoval/installationClip RemoverSlip-joint
PliersProtective Band
Screwdriver
Protective Band
Scraper

General Information - Repair Instruction1-6IllustrationRemoval/installation2. For Vehicles Equipped With SRS Airbag and Seat Belt Pretensioner
Tip: This is equipped with an SRS (Supplemental Restraint System), such as the driver airbag assembly,
front passenger airbag assembly airbag ECU and seat belt pretensioner. Failure to carry out service operations in
the correct sequence could cause the supplemental restraint system to unexpectedly deploy during servicing,
possibly leading to a serious accident. Further, if a mistake is made in servicing the supplemental restraint
system, it is possible the SRS may fail to operate when required. Before servicing (including removal or instal-
lation of parts, inspection or replacement), be sure to read the following items carefully, then follow the correct
procedure described in this manual.
(1) General NoticeInstall Remove
Install Remove a. Malfunction symptoms of the supplemental restraint system are difficult to confirm, so the diagnostic
trouble codes become the most important source of information when troubleshooting. When troubleshooting
the supplemental restraint system, always inspect the diagnostic trouble codes before disconnecting the battery.
b. Work must be started after 90 seconds from the time the ignition switch is turned to the "LOCK"
position and the negative (-) terminal cable is disconnected from the battery. (The supplemental restraint system
is equipped with a back--up power source so that if work is started within 90 seconds of disconnecting the
negative (-) terminal cable from the battery, the SRS may deploy.) When the negative (-) terminal cable is
disconnected from the battery, memory of the clock and audio systems will be cancelled. So before starting
work, make a record of the contents memorized by the each memory system. Then when work is finished, reset
the clock and audio systems as before. To avoid erasing the memory of each memory system, never use a back-
up power supply from another battery.

General Information - Repair Instruction1-7 (3) Driver Airbag Assembly
a. When removing the driver airbag assembly or handling a new driver airbag assembly, it should be placed
with the steering wheel top surface facing up. Storing the steering wheel with its top surface facing downward
may lead to a serious accident if the airbag deploys for some reason. In addition do not store a driver airbag
assembly on top of another one.
b. Never measure the resistance of the airbag squib. (This may cause the airbag to deploy, which is very
dangerous.)
c. Grease should not be applied to the driver airbag assembly and the pad should not be cleaned with
detergents of any kind. (2) Clock Spring (in combination switch)
The steering wheel must be fitted correctly to the steering col-
umn with the clock spring at the neutral position, otherwise clock
spring disconnection and other troubles may result.
c. Even in cases of a minor collision where the SRS does not deploy, the driver airbag assembly, front
passenger airbag assembly and seat belt pretensioner should be inspected.

e. Never use SRS parts from another vehicle. When replacing parts, replace them with new parts.

f. Before repairs, remove the airbag ECU if shocks are likely to be applied to the sensor during repairs.

g. Never disassemble and repair the airbag ECU assembly, driver airbag assembly, front passenger airbag
assembly or seat belt pretensioner.

h. If the airbag ECU assembly, driver airbag assembly, front passenger airbag assembly or seat belt
pretensioner has been dropped, or if there are cracks, dents or other defects in the case, bracket or connector,
replace them with new ones.

i. Do not directly expose the airbag ECU assembly, driver airbag assembly, front passenger airbag assem-
bly or seat belt pretensioner to hot air or flames.

j. Use a volt/ohmmeter with high impedance (10 k ohm/ V minimum) for troubleshooting of the electrical
circuit.
Information labels are attached to the periphery of the SRS components. Follow the instructions on the
notices.
After work on the supplemental restraint system is completed, check the SRS warning light MarkCorrectWrongd.
k.