2008 GEELY MK wiring diagram

Table of Contents IV Section 7 Rear Brake Drum ............................................................................................ 4-99
Section 8 Parking Brake System.......................................................................................4-106Part V Electric System & AccessoryChapter 1 Starting and Charging System......................................................................... 5-1
Section 1 Starting System (MR479Q, MR479QA, MR481QA) ...................................... 5-1
Section 2 Charging System (MR479Q, MR479QA, MR481QA) .................................... 5-3
Chapter 2 Combination Instrument System..................................................................... 5-7
Section 1 Wiring diagram of Combination Instrument and Location of Multi-pin Plug-in Terminal5-7
Section 2 Malfunction Symptom Table and Troubleshooting ......................................... 5-10
Chapter 3 Wiper and Washer System............................................................................... 5-21
Section 1 Wiper and Washer System Inspection ........................................................... 5-21
Section 2 Replacement and Adjustment ........................................................................ 5-23
Chapter 4 Light System...................................................................................................... 5-26
Section 1 Light System Introduction ............................................................................... 5-26
Section 2 Light System Malfunction Inspection ............................................................. 5-28
Section 3 Headlamp Replacement ................................................................................. 5-34
Section 4 Front Fog Lamp Replacement ...................................................................... 5-35
Section 5 Rear Combination Lamp Replacement .......................................................... 5-36
Section 6 High-mounted Stop light Replacement .......................................................... 5-36
Section 7 Front Reading Lamp Replacement ................................................................ 5-37
Section 8 Rear Reading Lamp Replacement ................................................................. 5-37
Section 9 License Plate Lamp Replacement ................................................................. 5-37
Chapter 5 Audio System..................................................................................................... 5-38
Section 1 Audio System Description .............................................................................. 5-38
Section 2 Audio System Connector Terminal Layout ..................................................... 5-40
Section 3 Audio System Inspection ................................................................................ 5-41
Section 4 Audio System Replacement ........................................................................... 5-52
Chapter 6 SRS (Supplemental Restraint System)............................................................ 5-54

Starting and Charging System-
Starting System5-23. WiringII. Starter assembly replacement (MR479Q, MR479QA, MR481QA)1. Remove starter assembly
(1) Disconnect starter connector.
(2) Remove nuts, disconnect starter cable.
(3) Remove 2 bolts and starter assembly.
2. Install starter assembly
Installation should be conducted in reversed direction of removal
Torque:
Bolt 37N.m
Wire harness 9. 8N.m (1) Check that connecting wire between positive pole of storage battery and starter must be firm and reliable,
outside shroud must be in good condition, so as to prevent generating electric spark and causing fire.
(2) Check whether wire is conducted, whether sheath is broken, if wiring harness is damaged, replace wiring
harness.Please Refer to "MK WIRING DIAGRAM"

Chapter 2 Combination Instrument SystemSection 1 Wiring diagram of Combination Instrument and
Location of Multi-pin Plug-in Terminal1. Schematic circuit diagram of combination instrument (see the figure)
2. Distribution of digital combination instrument plug-in unit terminalsCombination Instrument System -Wiring diagram of Combination Instrument and Location of Multi-pin Plug-in Terminal5-7combination instrument
combination instrument
combination instrument

Combination Instrument System -Wiring diagram of Combination Instrument and Location of Multi-pin Plug-in Terminal5-8Please Refer to "MK WIRING DIAGRAM"Wiring diagram of Combination Instrument

3. Definition of multi-pin plug-in unit terminal
1. Prompt:
R- red Bl- blue Y - yellow B- black P- pink G- green W- white
O- orange Gr - gray Br- brown V- purple Lg- olive drab
The first letter indicates primary color
The second letter indicates stripe colorTerminal
number1 MIL C 10 NA
2 Engine oil pressure switch YG 1 P
3 Brake fluid GR 2 R
4 Park G 3 N
5 Right turn light GB 4 D
6NA 52
7 EBD 6 L
8 Charge WR 7
9NA 8NA
10 NA 9 Sidelight GW
11 Safety belt YR 10 Start BR
12 NA 11 B+
13 Engine GY 12IG ( + ) Y
14 Safety gasbag RY 13 GND
15 NA 14 NA
16 IG ( + ) 15Speed sensor earthing B
1 NA 16 Speed signal input YR
2 Left turn light GW 17 Speed sensor power supply RY
3 High beam (+) RB 18 Key (ODO/TRIP) G
4 High beam (-) RW 19 Key (adjust brightness) YG
5 Foglight Gr 20 Key COM B
6 Rear defrost YB 21 Fuel gauge V
7 NA 22 ABS R
8 NA 23 Tachometer BBL
9 Door-lock warning lamp RBL 24 Coolant temperature gauge YWA
BCCombination Instrument System -Wiring diagram of Combination Instrument and Location of Multi-pin Plug-in Terminal5-9Definition of terminalConductor
ColorTerminal
numberDefinition of terminalConductor
Color

5-13 c. Check voltage between terminals
Standard:Tester connectionConditions Standard condition
C 12- ground Turn ignition switch to ON position 7. 5-9V
Result and measures:
Abnormal, repair or replace wiring harness or connector
Normal, replace combination instrument assy.
3. Tachometer fails
Checkout procedure
(1) Check combination instrument assy. rotating speed input
signal
a. Remove combination instrument assy. , keep connection of
connector.
b. Connect oscillograph to terminal C23 and ground.
c. Start up engine
d. Check signal waveform
Standard:
Display correct waveform
Result and measures:
Normal, check and replace combination instrument assy.
Abnormal, check engine ECU rotating speed output signal
(2) Check engine ECU rotating speed output signal
a. Remove engine ECU ware, keep connection of connector.
b. Connect oscillograph to terminal ECU 8# pin and ground.
c. Start up engine
d. Check signal waveform
Standard:
Display correct waveform
Result and measures:
Normal, repair or replace wiring harness or connector
Abnormal, check revolution speed transducer and engine
control system
4. Water thermometer fails
Circuit diagramCombination Instrument System -Malfunction Symptom Table and Troubleshooting combination instrument assy
combination instrument assy engine ECU
coolant Temperature SensorEngine Speed Signal
coolant Temperature Signal

Tester connection Conditions Standard state
C(60°C)164.5±5 ohm
C 24- ground 1/2C(90°C)56±3 ohm
H(115°C)28.7±2 ohmConditions Standard state
C(60°C)164.5±5 ohm
1/2C(90°C)56±3 ohm
H(115°C)28.7±2 ohm5-14 (1) Use diagnostic instrument to read engine water temperature value
a. Connect diagnostic instrument to diagnostic interface
b. Turn on ignition switch
c. Read water temperature value displayed on diagnostic instrument
Standard: the same as actual engine cooling water temperature
Result and measures:
Normal, water thermometer does not fail
Abnormal, check combination instrument assy.
(2) Check combination instrument assy.
a. Check resistance
Remove combination instrument assy. , disconnect connector.
Check connection between terminals
Standard:
Result and measures:
Normal, replace combination instrument assy.
Abnormal, check water temperature sensor
b. Check water temperature sensor
Remove water temperature sensor and put it in thermostat.
Adjust temperature of thermostat and measure resistance value of water temperature sensor
Standard:
Result and measures:
Normal, repair or replace wiring harness and connector
Abnormal, replace water temperature sensor
5. Fuel gauge fails
Circuit diagramCombination Instrument System -Malfunction Symptom Table and Troubleshooting combination instrument assy
Fuel Sensor
Fuel Signal

Suspected Area
1. Wire between CD box and main unit
2. CD box
3. CD bag
4. CD PLAYER main unit
1. Wire between CD box and main unit
2. CD box
1. CD box
2. CD box installation Symptom
CD can not be taken out
Sound quality poor only when playing CD
(Volume faint)
CD sound jumpTester connection Condition Standard state
GND and vehicle earth Normal status ON
Tester connection Condition Standard state
+B and GND Normal status 10-14V
ACC and GND Ignition switch is in ACC or ON 10-14VII. Trouble shooting1. Power switch system does
not work
Circuit diagram
Abnormal, repair or replace wiring harness, connector
Normal, check and replace radio assembly (1) Check radio assembly (+ B, ACC, GND)
a. As shown in the table below, check connection between terminals in each operating condition.
Standard:
b. As shown in the table below, check voltage between terminals in each operating condition.
Standard:Fuse Box in Engine
CompantmentAudio System -Audio System Inspection5-42MAIN
60AFuse Box under
Instrument Panel