2008 GEELY MK wiring diagram

Tester connection Condition Standard state
TAIL and GND Combination switch (light switch) 10-14V2. Turn on light switch, radio backlight
does not illuminate
Circuit diagram
(1) Check radio assembly (TAIL)
As shown in the table below, check voltage between terminals in each operating condition.
Standard:
Abnormal, repair or replace wiring harness, connector
Normal, check and replace radio assembly
3. Loudspeakers is silent in all modes
Circuit diagramAudio System -Audio System Inspection5-43 lamp switch
Please Refer to "MK WIRING DIAGRAM"

VIII. Circuit diagramVII. Check list index of fault without fault codeMK-60 ABS system -ABS Diagnosis5-101Fault condition
When Ignition switch is turned to "ON " (engine stall condition), ABS
warning lamp does not illuminate
After Engine is started, warning lamp does not go outCheck list No.
1
2
3
4
5
6Reference page
5-109
5-110
5-111
5-112
5-112
5-113 ABS works
abnormallyBraking force on both sides is not even
Braking force is insufficient
When brake pedal is stepped on slightly, ABS works
(automobile in idle state)
When brake pedal is stepped on slightly, ABS works
(automobile in running state)
When ABS works, brake pedal vibrates excessively
Travel of brake pedal is too long
A very large force is needed to step on brake pedal
No fault code output (cannot communicate with fault diagnosis instrument)Please Refer to "MK WIRING DIAGRAM"

ABS HECU assy.III. Replace hydraulic control unit1. Press lock catch on joint side, remove wire harness of pump motor.
2. Remove 4 screws as as shown in the figure, the removed old screws
can not be reused.
3. Separate hydraulic control unit HCU from electronic control unit
ECU.
4. Mount new hydraulic control unit HCU onto electronic control unit
ECU.
5. Use new screw to fix ECU onto HCU, tightening moment: 3-4N.m.
6. Insert motor wiring harness, note that lock catch must be in right
position.MK-60 ABS system -
Removal and Installation5-117Schematic diagram for removal of ABS HECU brake oil pipe5. When system is opened, don't use compressed air or move the vehicle.
6. After removing ABS assembly, use appropriate plugs to plug up hydraulic delivery outlets as soon as possible.
Remove other parts that might hinder work.
7. Please use HZY4 brake fluid, do not use mineral oil.
8. Use brake fluid to soak sealing member and Oring, do not use engine oil or brake ointment.
9. After repair, check whether function of routine brake system and ABS brake is reliable and normal or not.
10. Check whether there is any leakage at all Hydraulic couplers.II. Removal of HECU1. Turn off ignition switch and disconnect storage battery minus earth wire.
2. Remove wiring harness plug from ABS HECU assembly.
3. Step down the pedal >60mm, use pedal bracket to fix it, so master cylinder center valve will be turned off, when
system is opened, brake fluid will not flow out from outlet.
4. Put a clean pad under hydraulic controller.
5. Firstly remove brake hard tube (A, B) on HCU connecting with master cylinder, make sign. Plug up the outlet
with a plug immediately.
6. Remove brake pipe (1 - 4) to wheels and make sign. Plug up the outlet with a plug immediately.
7. Remove the screw cap fixing HECU onto the bracket.
8. Remove the entire HECU from bracket.

Chapter 10 On-board Vehicle TelephoneI. Key points for use of Geely hands-free car telephone: 1. Microphone of hands-free car telephone is installed on the back of steering wheel upright column, away from
driver to ensure talking effect. During talking, do not open window, otherwise noisy wind might influence talking
effect.
2. Since there are many kinds of mobile phones in Chinese market, in order to ensure talking effect, please
select interface line corresponding to your mobile phone, otherwise talking effect might be influenced. At present,
Nokia, Motorola, Siemens interface lines are available.
3. To use, insert one end of mobile phone interface line into 8 core RJ 45 stand on automobile panel, connect
the other end to earphone output port of the mobile phone. When mobile phone is not connected, automobile sound
works normally, when mobile phone receive a call, CD becomes quiet automatically, at the same time, loudspeaker
in the vehicle is switched to hands-free telephone output. This hands-free car telephone is provided with response
button at the top of microphone, however, new style of mobile phone does not support manual response function
for the time being, while supports automatic response function, namely it receive the call automatically after
ringing for three times.
4. After talking is finished, automobile sound will return to original state automatically.
5. During daily use, note that contact insertion and withdraw force of mobile phone interface line should not
be too large, so as to avoid damage.
6. Hands-free car telephone has no volume switch, volume of loudspeaker voice may be adjusted by regulating
the volume of handset earphone.II. Circuit diagram5-129On Board Vehicle Telephone-On-board Vehicle TelephonePlease Refer to "MK WIRING DIAGRAM"

Rear Parking Radar System-Rear Parking Radar System5-131Ultrasonic sensor
Ultrasonic sensor
Receiving AmplifierTransmitting Amplifier Receiving AmplifierTransmitting AmplifierPhonetic circuitMCU
Receive, filter and amplifyDisplay
Electric A/D switchChapter 11 Rear Parking Radar SystemI. System principle Reversing radar system mainly adopts ultrasonic ranging technology, utilizes piezoelectric property of
transducer (ultrasonic sensor), excites piezo sheet with voltage with frequency of 40KHZ intermittently, this piezo
sheet is then converted from electric energy to mechanical energy and sent out. When emitted sound wave contacts
object, it will reflect weak sound wave energy to transducer according to sound wave reflection principle, i. e.
convert received weak acoustic vibration signal to electrical signal, after signal amplification processing, it is
transmitted to microprocessor to calculate the distance between vehicle and this object and display the distance.
Then microprocessor determines whether to give caution remind for dangerous object according to varying
degrees.II. Circuit diagramPlease Refer to "MK WIRING DIAGRAM"

Door Glass Regulating and Power Door Lock Control-
Door Glass Regulating System5-1415. Electric circuit diagramfor door glass regnlating system
Please Refer to "MK WIRING DIAGRAM"