2006 LAND ROVER FRELANDER 2 engine

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Oil Pump
Removal and Inst all ati on
Special T ool(s) 303-1280
Remover, Oi l Pump Pin
Removal CAUTION: Extreme cleanli nes s mus t be exercis ed when handli ng thes e component s.
• NOTE: Always fit a new oil pump , as t he pump gear is sprayed wi th a 's pacecoat' t hat al lows accurate set ti ng of the
backlas h ..
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
2. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
2.
Remove t he oil pan.
Refer t o: Oil Pan (303-01A Engi ne - I6 3.2L Pet rol, Removal and
Inst all at ion).
3.
4. CAUTION: Di scard the s eal.
Remove t he oil s trainer pick-up as sembl y.
4. 5. CAUTION: Di scard the s eals .
Remove t he oil pres s ure pi pe.
5.
Remove t he oil pump pivot pin.
Speci al Tool (s ): 303-1280 6.

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Oil Cooler
Removal and Inst all ati on
Removal
1. W ARNING: Do not work on or under a vehi cle s upported onl yby a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
1.
Drai n t he cool ing s ys tem.
Refer t o: Cool ing Sys tem Drai ni ng, Fi lli ng and Bleeding (303-03AEngine Cooli ng - I6 3.2L Petrol, General Procedures).
2.
Remove t he int ake mani fol d as sembl y.
Refer t o: Int ake Mani fol d (303-01A Engi ne - I6 3.2L Petrol, Removaland Inst all at ion).
3.
Remove t he dips ti ck tube.4.
Loosen t he element cover 4 compl ete t urns t o al low engine oi l todrai n from the fil ter cover.5.
6. CAUTION: Be prepared to col lect escaping oil .
Remove t he oil fi lt er ass embly.
6.
Remove and dis card t he gas ket .7.

Remove and dis card t he 2 gas ket s .
11.
Installation
Inst all new gas ket s .
1.
Inst all t he engi ne oil cool er.
T orque: 10 Nm 2.
Inst all t he hos e.
T orque: 10 Nm 3.
Inst all and t ighten t he engine oi l fil ter.
T orque: 5 Nm 4.
Inst all t he cool ant hos e.
5.
Inst all t he new gasket .
6.
Inst all t he dips ti ck tube.
T orque: 10 Nm 7.
Inst all t he int ake mani fol d as sembl y.
Refer t o: Int ake Mani fol d (303-01A Engi ne - I6 3.2L Petrol, Removal
and Inst all at ion).
8.
Fil l and bl eed the cooli ng s ys t em.
Refer t o: Cool ing Sys tem Drai ni ng, Fi lli ng and Bleeding (303-03A
Engine Cooli ng - I6 3.2L Petrol, General Procedures).
9.
Check and top-up the engine oi l if required.
10.

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Oil Filter Element
Removal and Inst all ati on
Removal
Releas e t he PAS fl uid reservoi r from t he bracket and ti e as ide.
1. Loosen t he element cover 4 compl ete t urns t o al low
engine oil t o drai n from the fil ter cover.
2. 3.
Installation Inst all t he oil fi lt er element.
1.
Inst all t he engi ne oil filt er.
T orque: 25 Nm 2.
Secure t he res ervoir.
3.
Check and top-up the engine oi l.
4.

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Engine Upper Support Insulator
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s. T orque:
10 Nm 1.
T orque:
110 Nm 2.
Installation To i nst all , revers e t he removal procedure.
1.

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Engine Lower Support Insulator
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s. All vehicles
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he engi ne undershi eld.
Refer t o: Engi ne Unders hi eld (501-02 Front End Body Panel s ,
Removal and Ins tall ati on).
2. 3. CAUTION: Make s ure that thes e component s
are ins tal led t o t he noted removal pos it ion.
Remove t he lower s upport ins ul ator.
T orque: 110 Nm 3.
Vehicles with petrol engine 4.
NOTE: Do not dis ass embl e further if t he component
i s removed for acces s onl y.
Remove t he heat s hiel d.
T orque: 10 Nm 4.
All vehicles

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Engine Mount LH
Removal and Inst all ati on
General Equipment
Trans mi ss i on jack
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he engi ne undershi eld.
Refer t o: Engi ne Unders hi eld (501-02 Front End Body Panel s ,Removal and Ins tall ati on).
2.
Support the trans mi s si on.
General Equi pment: Trans mi ss i on jack
3.
Remove t he air cleaner as s embly.
Refer t o: Air Cleaner (303-12A Intake Ai r Dis tribut ion and Fil tering -I6 3.2L Pet rol, Removal and Ins t al lat ion).
4.
Remove t he bat t ery t ray.
Refer t o: Bat t ery Tray (414-01 Bat tery, Mount ing and Cables ,Removal and Ins tall ati on).
5.
6. W ARNING: Make sure t hat new nut s arei ns t alled.
• NOTE: Vehicles wi th aut omat ic t rans mis s ion have abreat her pi pe att ached t o t he mounti ng.
Remove t he bracket .
T orque:M12 80 NmM8 25 Nm
6.
Remove t he engi ne mount LH.
T orque: 175 Nm
7.Installation
To i nst all , revers e t he removal procedure.1.

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Engine Mount RH
Removal and Inst all ati on
Special T ool(s)
303-1254Support , Engine
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he engi ne undershi eld.
Refer t o: Engi ne Unders hi eld (501-02 Front End Body Panel s ,Removal and Ins tall ati on).
2.
Remove t he RH front wheel and t ire.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal andInst all at ion).
3.
Remove t he fender spl as h shi el d extens ion panel.4.