2006 LAND ROVER FRELANDER 2 engine

Stage 1:
Stage 2:
T orque:
75 Nm 90°
Tight en the inlet cams haft dri ve sprocket.
T orque: 110 Nm 7.
Remove t he camshaft al ignment s pecial t ool .
8.
9. CAUTIONS: Make s ure that t he area around the component i s clean and
free of foreign mat eri al. The pl ugs must be ins tall ed dry.
Inst all new cams haft bore pl ugs .
9.
Remove t he cranks haft l ocking tool.
10.
Inst all t he cranks haft front oil s eal.
Refer t o: Engi ne Front Seal (303-01A Engi ne - I6 3.2L Pet rol,
Removal and Ins tall ati on).
11.
Inst all t he ti ming cover.
Refer t o: Timi ng Cover (303-01A Engi ne - I6 3.2L Pet rol, Removal
and Inst all at ion).
12.
Inst all t he RH engine mount .
Refer t o: Engi ne Mount RH (303-01A Engi ne - I6 3.2L Petrol,
Removal and Ins tall ati on).
13.
Connect t he batt ery ground cable and ins tall t he cover.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
14.

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Exhaust Manifold
Removal and Inst all ati on
Special T ool(s) 310-121
W rench, H02S
Removal W ARNING: Observe due care when worki ng near a hot exhaust s ys tem.
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he engi ne cover.
Refer t o: Engi ne Cover - I6 3.2L Pet rol (501-05 Int eri or Trim and
Ornament ati on, Removal and Ins tal lat ion).
2.
Remove t he cat alyti c convert ers .
Refer t o: Cat alyt ic Converter (309-00A Exhaus t Syst em - I6 3.2L
Petrol, Removal and Ins tall ati on).
3.
Remove t he RH fender s plas h s hield.
Refer t o: Fender Spl ash Shi eld (501-02 Front End Body Panel s ,
Removal and Ins tall ati on).
4.
Di sconnect t he heat ed oxygen s ens ors (HO2S) el ect ri cal connectors .
5. 6. W ARNING: Do not twi s t the HO2S wiring
harnes s on removal . Fai lure to foll ow t his i ns t ructi on
may res ul t in damage to t he component .
Remove t he 2 HO2S.
Speci al Tool (s ): 310-121 6.

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Cylinder Head
Removal and Inst all ati on
Removal
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
2. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
2.
Remove t he fuel rai l.
Refer t o: Fuel Rail (303-04A Fuel Chargi ng and Cont rol s - I6 3.2LPetrol, Removal and Ins tall ati on).
3.
Remove t he generat or.
Refer t o: Generator - I6 3.2L Pet rol (414-02 Generator andRegulator, Removal and Ins t allat ion).
4.
Remove both exhaust mani fol ds .
Refer t o: Exhaus t Mani fol d (303-01A Engi ne - I6 3.2L Petrol,Removal and Ins tall ati on).
5.
Remove t he camshaft s .
Refer t o: Camshafts (303-01A Engine - I6 3.2L Pet rol , Removal andInst all at ion).
6.
Releas e t he fuel pipe.7.

Installation
Inst all t he dowel s .
1.
Clean and i nspect the cyli nder head and cylinder block.
2. Check cyli nder head face for dis torti on, acros s t he
cent er and from corner t o corner.
Refer t o: Specificati ons (303-01A Engine - I6 3.2L
Petrol, Speci fi cat ions ).
3.
4. CAUTION: The head gasket mus t be i ns t alled over t he
cylinder block dowel s .
Inst all a new cyli nder head gas ket .
4.
5. CAUTION: Make s ure that the component is correct ly locat ed
on t he locati ng dowels .
• NOTE: This st ep requires t he aid of another t echnician.
Inst all t he cyl inder head.
5. 6.
CAUTIONS: Make s ure that new cyli nder head bolt s are
i ns t alled. Take extra care not t o damage t he mati ng faces .
• NOTE: The cylinder head ti ght ening proces s is carri ed
out once to 45 Nm, then t he bolt s are loos ened and t he
final torque and angle appl ied.
• NOTE: The cylinder head ti ght ening proces s is carri ed
out once to 45 Nm, then t he bolt s are loos ened and t he
final torque and angle appl ied.
Tight en the cyli nder head bolt s in the sequence
s hown.
T orque: 45 Nm Check the cyli nder head bolt t orque in the
s equence s hown.
T orque: 45 Nm Tight en the cyli nder head bolt s in the sequence
s hown.
T orque: 90° Tight en the cyli nder head bolt s in the sequence
s hown.
T orque: 180° 6.

7. CAUTION: Make s ure that the choke valves (1),
(2) are i n place.
7.
8. CAUTIONS: Ext reme cl eanli ness must be exerci sed when handli ng t hes e
component s. Make s ure that t hes e component s are ins tal led t o t he noted
removal posi ti on.
Inst all t he tappets .
8.
9. CAUTIONS: Ext reme cl eanli ness must be exerci sed when handli ng t hes e
component s. Make s ure that t hes e component s are ins tal led t o t he noted
removal posi ti on.
Inst all t he las h adjus ters .
9.
Inst all t he engi ne wiring harnes s cli ps.
T orque: 6 Nm 10.
Inst all t he s park plugs .
T orque: 28 Nm 11.
Secure t he fuel li ne.
T orque: 10 Nm 12.
Inst all t he camshaft s .
Refer t o: Camshafts (303-01A Engine - I6 3.2L Pet rol , Removal and
Inst all at ion).
13.
Inst all t he generat or.
Refer t o: Generator - I6 3.2L Pet rol (414-02 Generator and
Regulator, Removal and Ins t allat ion).
14.
Inst all t he fuel rai l.
Refer t o: Fuel Rail (303-04A Fuel Chargi ng and Cont rol s - I6 3.2L
Petrol, Removal and Ins tall ati on).
15.

Publi s hed: 11-May-2011
Engine - I6 3.2L Petrol - Oil Pan
Removal and Inst all ati on
Removal
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
2. W ARNING: Do not work on or under a vehi cle s upported onl yby a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
2.
Remove t he s tart er mot or.
Refer t o: Start er Motor (303-06A Starti ng Sys t em - I6 3.2L Pet rol ,Removal and Ins tall ati on).
3.
4. W ARNING: Be prepared t o coll ect es capi ng oil.
CAUTION: Di scard the seal.
Remove t he lubri cant drai n plug.
4.
Di sconnect t he oil level sens or elect rical connect or.5.

Remove t he 3 oil pan bolt s .
10. Remove t he 31 oil pan bolt s
11.
Remove t he oil pan gasket .
12. 13.
NOTE: Do not dis ass emble further if t he component
i s removed for acces s onl y.
Remove t he oil level sens or.
13.
Installation Inst all t he oil level sens or.
T orque: 8 Nm 1.
For seal ant i nformat ion, refer to the engine specificat ion secti on.
Refer t o: Specificati ons (303-01A Engine - I6 3.2L Petrol ,
Speci fi cat ions ).
2.

Apply a bead of s ealant, 2.5 mm diamet er, t o t he area
i ndi cat ed.
3.
Inst all t he oil pan.
T orque: M7 17 Nm M10
45 Nm 4.
Secure t he cool ant rail .
T orque: 10 Nm 5.
Inst all t he int ake mani fol d.
T orque: 10 Nm 6.
7. CAUTION: Make s ure that new s ealing was hers are i nst all ed.
Inst all t he lubri cant drai n plug.
T orque: 38 Nm 7.
Fil l the engine wit h oil .
8.
Inst all t he s tart er mot or.
Refer t o: Start er Motor (303-06A Starti ng Sys t em - I6 3.2L Pet rol ,
Removal and Ins tall ati on).
9.
Check and top-up the engine oi l.
10.
Connect t he batt ery ground cable and ins tall t he cover.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
11.
Inst all t he dips ti ck tube.
T orque: 10 Nm 12.