2001 TOYOTA SEQUOIA Page 18

BO43A±02
± BODYINSTRUMENT PANEL
BO±97
3650 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page BO±89).
1. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
2. PERFORM INITIALIZATION (See page IN±20)
Some systems need initialization when disconnecting the cable from the negative battery terminal.

BO46X±01
BO±108
± BODYROOF HEADLINING
3661 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page BO±101).

BO4S7±01
± BODYFRONT SEAT (Power Adjuster Type)
BO±111
3664 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
CAUTION:
Work must not be started until at least 90 seconds after the ignition switch is turned to the LOCK posi-
tion and the negative (±) terminal cable is disconnected from the battery.
(The SRS is equipped with a back±up power source. If work is started within 90 seconds from discon-
necting the negative (±) terminal cable of the battery, the SRS may deploy.)
NOTICE:
When removing/installing and overhauling the passenger seat, check the passenger occupant clas-
sification system and perform the zero point calibration (see page DI±1128).
HINT:
The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.
2. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the seat track covers.
HINT:
Tape the screwdriver tip before use.
3. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) Disconnect the connectors.
(c) w/ Side airbag:
Disconnect the airbag connector.
(d) Remove the front seat.
NOTICE:
Be careful not to damage the body.

H24327
BO±116
± BODYFRONT SEAT (Power Adjuster Type)
3669 Author: Date:
2005 SEQUOIA (RM1146U)
16. REMOVE RH AND LH SEATBACK SHIELDS
(a) Remove the 2 screws and RH seatback shield.
(b) Perform the same procedure on the other side.
17. REMOVE VERTICAL ADJUSTER BRACKET INNER
AND OUTER COVERS
(a) Remove the screw and vertical adjuster bracket inner
cover.
(b) Perform the same procedure on the other side.
18. Driver 's seat:
REMOVE SEAT POSITION SENSOR
(See page RS±104)

BO4SA±01
H24327
H24326
H24325
± BODYFRONT SEAT (Power Adjuster Type)
BO±117
3670 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:

The procedures listed below are for the LH side.

A bolt without a torque specification is shown in the stan-
dard bolt chart (see page SS±2).
1. Driver 's seat:
INSTALL SEAT POSITION SENSOR
(SEE PAGE RS±108)
2. INSTALL VERTICAL ADJUSTER BRACKET INNER
AND OUTER COVERS
(a) Install the vertical adjuster bracket inner cover with the
screw.
(b) Perform the same procedure on the other side.
3. INSTALL RH AND LH SEATBACK SHIELDS
(a) Install the RH seatback shield with the 2 screws.
(b) Perform the same procedure on the other side.
4. INSTALL RH AND LH RECLINING ADJUSTER INSIDE
COVERS
(a) Connect the wire harness clamp.
(b) Install the RH reclining adjuster inside cover with the
screw.
(c) Perform the same procedure on the other side.
5. INSTALL LUMBAR SUPPORT ADJUSTER
(a) Install a new bushing to the lumbar support adjuster.
(b) Install the lumbar support adjuster with the 2 screws.

BO4S9±01
± BODYFRONT SEAT (Power Adjuster Type)
BO±123
3676 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:
The procedures listed below are for the LH side.
1. INSTALL FRONT SEAT
(a) Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the vehicle body.
(b) w/ Side airbag:
Connect the airbag connector.
(c) Connect the connectors.
(d) Slide the front seat to the rearmost position.
(e) Tighten the bolts on the front side temporarily, starting from the bolt on the inner side.
(f) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
(g) Slide the front seat to the foremost position.
(h) Tighten the bolts on the rear side temporarily, starting from the bolt on the inner side.
(i) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
2. INSTALL SEAT TRACK COVERS
3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
4. Passenger 's seat:
PERFORM PASSENGER OCCUPANT CLASSIFICATION SYSTEM ZERO POINT CALIBRATION
(See page DI±1128)
5. PERFORM INITIALIZATION (See page IN±20)
Some systems need initialization when disconnecting the cable from the negative battery terminal.

BO4SC±01
± BODYFRONT SEAT (Manual Adjuster Type)
BO±125
3678 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
CAUTION:
Work must not be started until at least 90 seconds after the ignition switch is turned to the LOCK posi-
tion and the negative (±) terminal cable is disconnected from the battery.
(The SRS is equipped with a back±up power source. If work is started within 90 seconds from discon-
necting the negative (±) terminal cable of the battery, the SRS may deploy.)
NOTICE:
When removing/installing and overhauling the passenger seat, check the passenger occupant clas-
sification system and perform the zero point calibration (see page DI±1128).
HINT:
The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.
2. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the seat track covers.
HINT:
Tape the screwdriver tip before use.
3. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) Disconnect the connectors.
(c) w/ Side airbag:
Disconnect the airbag connector.
(d) Remove the front seat.
NOTICE:
Be careful not to damage the vehicle body.

H24343
H24341
± BODYFRONT SEAT (Manual Adjuster Type)
BO±129
3682 Author: Date:
2005 SEQUOIA (RM1146U)
13. REMOVE RH AND LH LOWER RECLINING ADJUSTER
INSIDE COVERS
(a) Remove the screw and LH lower reclining adjuster inside
cover.
(b) Perform the same procedure on the other side.
14. REMOVE RH AND LH SEAT CUSHION LOWER
SHIELDS
(a) Using a screwdriver, disengage the claw and remove the
LH seat cushion lower shield.
HINT:
Tape the screwdriver tip before use.
(b) Perform the same procedure on the other side.
15. Driver 's seat:
REMOVE SEAT POSITION SENSOR
(See page RS±104)