2001 TOYOTA SEQUOIA Page 18

BE±104
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
3508 Author: Date:
2005 SEQUOIA (RM1146U)
2. REPLACE DOOR CONTROL RECEIVER AND TRANS-
MITTER
NOTICE:
When replacing the door control receiver and transmitter,
registration of recognition code is necessary because they
are provided as single components.
(a) Select one of the operations mode should be performed
from the following modes.
Add mode
Rewrite mode
Prohibition mode
Confirmation mode
HINT:
The add mode is used to retain codes already registered
while you register new recognition codes. This mode is
used when adding a transmitter. However, if the number
of registered codes exceeds 4 codes, previously regis-
tered codes are correspondingly erased in order, starting
from the first registered code.
The rewrite mode is used to erase all previously regis-
tered codes and register only new recognition codes.
The prohibition mode is used to erase all registered codes
and cancels the wireless door lock function. Use this
mode when the transmitter is lost.
The confirmation mode is for confirming how many recog-
nition codes are already registered before you register
additional recognition codes.
(b) Follow the chart on the following pages to register the
transmitter recognition code at the wireless door lock con-
trol receiver.
HINT:
When procedure is out of the specified, the operation re-
turns to normal operation.
Maximum 4 recognition codes can be registered.

I18597
BE26F±03
I18598
I18599
BE±134
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
3538 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT GARAGE DOOR OPENER SWITCH
(a) Press the switch and check that each garage door indica-
tor (green) comes on.
(b) Even if only one switch does not come on, replace it.
2. INSPECT GARAGE DOOR OPENER REGISTRATION
AND TRANSMITTING
HINT:
Use the home link tester made by KENT MORE for this test.
As it is necessary to record the code of the hand held transmit-
ter, customer's code will be erased. When the inspection is
complete, please register the customer's again.
(a) Check that the inspection code of the hand held transmit-
ter can be recorded (See page BE±129).
If the code can not be registered, replace the garage door open-
er.
(b) Press the switch which an inspection code has been reg-
istered for and check that garage door indicator (green)
of the home link tester comes on.
If the garage door indicator (green) does not come on, replace
the garage door opener.

BE0FZ±25
I24377
I24378
I04197
± BODY ELECTRICALHORN SYSTEM
BE±145
3549 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT HORN SWITCH
(a) Disconnect the negative (±) terminal from the battery.
(b) Remove the left and right covers from the steering wheel.
(c) Using a torx socket wrench, loosen the 2 bolts.
(d) Pull up the horn pad and place it on the steering column,
as shown.
HINT:
Do not disconnect the connector from the horn pad.
(e) Disconnect the connector from the slip ring.
(f) Check that no continuity exists between terminal 6 of the
connector and body ground.
(g) Check that continuity exists between terminal 6 of the
connector and body ground when the horn contact plate
is pressed against the steering spoke assembly.
If continuity is not as specified, repair or replace the steering
wheel or wire harness as necessary.
(h) Install the horn pad in place and using a torx socket
wrench, torque the 2 bolts.
Torque:
7.1 N´m (72 kgf´cm, 62 in.´lbf)
(i) Install the left and right covers.
(j) Connect the negative (±) terminal to the battery.
2. INSPECT HORN OPERATION
Connect the positive (+) lead from the battery to the terminal
and negative (±) lead to the horn body and check that the horn
blows.
If operation is not as specified, replace the horn.
3. INSPECT HORN SWITCH CIRCUIT
(See page DI±1764)

I01200
2 1
35
2 5
1 3
BE±146
± BODY ELECTRICALHORN SYSTEM
3550 Author: Date:
2005 SEQUOIA (RM1146U)
4. INSPECT HORN RELAY CONTINUITY
ConditionTester connectionSpecified condition
Always1 ± 2Continuity
Always3 ± 5No continuity
Apply B+ between
terminals 1 and 2.3 ± 5Continuity
If continuity is not as specified, replace the relay.
5. INSPECT HORN RELAY CIRCUIT
(See page DI±1764)

BO4S4±01
± BODYBATTERY
BO±1
3554 Author: Date:
2005 SEQUOIA (RM1146U)
BATTERY
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77

BO45N±01
H16657
H16658
Z06435
± BODYFRONT DOOR
BO±15
3568 Author: Date:
2005 SEQUOIA (RM1146U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
Using SST, adjust the door by loosening the body side hinge
bolts.
SST 09812±00010
Torque: 23 N´m (235 kgf´cm, 17 ft´lbf)
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Adjust the door by loosening the door side hinge bolts.
HINT:
Substitute the standard bolt for the centering bolts.
(See page BO±7)
Torque: 23 N´m (235 kgf´cm, 17 ft´lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are adjusted
correctly.
(b) Adjust the striker position by slightly loosening the striker
mounting screws, and hitting the striker with a hammer.
(c) Tighten the striker mounting screws again.
Torque: 23 N´m (235 kgf´cm, 17 ft´lbf)

BO45O±01
BO±16
± BODYFRONT DOOR
3569 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page BO±10).

BO45R±01
H16668
H16669
BO2556
± BODYREAR DOOR
BO±23
3576 Author: Date:
2005 SEQUOIA (RM1146U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/ REARWARD AND VER-
TICAL DIRECTIONS
(a) Remove the front and rear door scuff plates.
(b) Remove the center pillar lower garnish.
(c) Remove the front seat outer belt (See page BO±101).
(d) Loosen the body side hinge nuts to adjust.
Torque: 23 N´m (230 kgf´cm, 17 ft´lbf)
(e) Install the front seat outer belt and center pillar lower gar-
nish (See page BO±101).
(f) Install the front and rear door scuff plates.
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
Torque: 23 N´m (230 kgf´cm, 17 ft´lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are adjusted
correctly.
(b) Loosen the striker mounting screws to adjust.
Torque: 23 N´m (230 kgf´cm, 17 ft´lbf)
(c) Using a plastic hammer, tap the striker to adjust it.