2001 TOYOTA SEQUOIA Page 18

BO4SE±01
H24343
H24342
H24395
BO±130
± BODYFRONT SEAT (Manual Adjuster Type)
3683 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:

The procedures listed below are for the LH side.

A bolt without a torque specification is shown in the stan-
dard bolt chart (see page SS±2).
1. Driver 's seat:
INSTALL SEAT POSITION SENSOR
(SEE PAGE RS±108)
2. INSTALL RH AND LH SEAT CUSHION LOWER
SHIELDS
3. INSTALL RH AND LH LOWER RECLINING ADJUSTER
INSIDE COVERS
(a) Install the LH lower reclining adjuster inside cover with the
screw.
(b) Perform the same procedure on the other side.
4. INSTALL RH AND LH UPPER RECLINING ADJUSTER
INSIDE COVERS
(a) Install the LH upper reclining adjuster inside cover with
the screw.
(b) Perform the same procedure on the other side.
5. INSTALL SEAT CUSHION COVER
Install the seat cushion cover to the seat cushion pad with the
hog rings.
HINT:
When installing the hog rings, take as much care as possible to
prevent wrinkles.
6. INSTALL SEAT CUSHION COVER AND PAD
(a) Install the seat cushion cover with seat cushion pad, and
latch the seat cushion cover hooks.

BO4SF±01
BO±134
± BODYFRONT SEAT (Manual Adjuster Type)
3687 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:
The procedures listed below are for the LH side.
1. INSTALL FRONT SEAT
(a) Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the vehicle body.
(b) w/ Side airbag:
Connect the airbag connector.
(c) Connect the connectors.
(d) Slide the front seat to the rearmost position.
(e) Tighten the bolts on the front side temporarily, starting from the bolt on the inner side.
(f) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
(g) Slide the front seat to the foremost position.
(h) Tighten the bolts on the rear side temporarily, starting from the bolt on the inner side.
(i) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
2. INSTALL SEAT TRACK COVERS
3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
4. Passenger 's seat:
PERFORM PASSENGER OCCUPANT CLASSIFICATION SYSTEM ZERO POINT CALIBRATION
(See page DI±1128)
5. PERFORM INITIALIZATION (See page IN±20)
Some systems need initialization when disconnecting the cable from the negative battery terminal.

BO4SG±01
H17260
H23459
Hook
± BODYREAR NO.1 SEAT (Separate Type)
BO±137
3690 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:

The procedures listed below are for the RH side.

A bolt without a torque specification is shown in the stan-
dard bolt chart (see page SS±2).

Tape the screwdriver tip before using it to remove the
parts.
1. REMOVE HEADREST
2. REMOVE RECLINING ADJUSTER RELEASE HANDLE
3. REMOVE NO. 1 REAR SEAT RECLINING COVER
(a) Remove the screw and No. 1 rear seat reclining cover.
(b) Perform the same procedure on the other side.
4. REMOVE SEATBACK ASSEMBLY
(a) Tilt the seat forward.
(b) As shown in the illustration, disengage the hook and open
the seatback cover.
(c) Remove the 4 bolts and the seatback assembly.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
5. REMOVE SEATBACK COVER
(a) Remove the headrest supports.
(b) Disengage the hooks, and remove the seatback frame
from the seatback cover with pad.
(c) Remove the seatback cover from the seatback pad.
HINT:
At the time of reassembly, take as much care as possible to
minimize wrinkles when installing hog rings.

BO4RB±02
± BODYREAR NO.1 SEAT (Separate Type)
BO±139
3692 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (see page BO±137).

BO4RC±02
BO±140
± BODYREAR NO.1 SEAT (Separate Type)
3693 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (see page BO±136).

BO4SJ±01
H05304
H05321
± BODYREAR NO.1 SEAT (Split Type LH)
BO±143
3696 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:

A bolt without a torque specification is shown in the stan-
dard bolt chart (see page SS±2).

Tape the screwdriver tip before using it to remove the
parts.
1. REMOVE HEADREST
2. REMOVE RECLINING ADJUSTER RELEASE HANDLE
3. REMOVE NO. 1 RECLINING COVERS
(a) Zip the seat cushion cover open.
(b) Remove the 2 screws and 2 No. 1 reclining covers.
4. REMOVE SEAT CUSHION UNDER COVER
(a) Remove the 2 screws and 2 seat cushion under covers.
(b) Remove the 10 screws and seat cushion under cover
sub±assembly.

BO4SK±01
± BODYREAR NO.1 SEAT (Split Type LH)
BO±147
3700 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page BO±143).

BO4SL±01
BO±148
± BODYREAR NO.1 SEAT (Split Type LH)
3701 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page BO±142).