2020 MITSUBISHI ASX Owner's Manual (in English)

1-Room lamp (rear) *
: 8 W
2- Vanity mirror lamps *
: 2 W
3- Room lamp (front) & map lamps: 8 W 4- Luggage room lamp: 5 W
5- Centre console down lamp
6- Glove box lamp: 1.4 WNOTEz The Centre console down lamp uses an LED
instead of a bulb. If you need to repair or re-
place this lamp, contact a MITSUBISHI
MOTORS Authorized Service Point.HeadlampsNOTEz An LED, not a bulb, is used in the head
lamps. Contact a MITSUBISHI MOTORS
Authorized Service Point when there is a need for repair or replacement.* If so equippedDaytime running lamps/Posi-
tion lampsNOTEz An LED, not a bulb, is used in the daytime
running lamps/position lamps. Contact aMITSUBISHI MOTORS Authorized Serv-
ice Point when there is a need for repair or
replacement.Front turn-signal lamps
1. Except for vehicles for Moldova and
Ukraine, when replacing the bulb on the
left side of the vehicle, remove the bolt
(A), and then move the sub fuse box and
bracket right side of the vehicle.
*: Front of the vehicle
2. While holding down the tab (B), pull out
the socket (C).
*: Front of the vehicle
3. Turn the socket (D) anticlockwise to re-
move it.
*: Front of the vehicle
Replacement of lamp bulbs
10-252*$(20(1Maintenance10

4.Remove the bulb from the socket by
turning it anticlockwise while pressing
in.
5. To install the bulb, perform the removal
steps in reverse.
Side turn-signal lamps (on
fender)*NOTEz For the side turn-signal lamps (on fender), it
is not possible to repair or replace just the
bulb.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Side turn-signal lamps (on out-
side rear-view mirror)*NOTEz An LED, not a bulb, is used in the side turn-
signal lamps (on outside rear-view mirror).
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Front fog lamps*NOTEz An LED, not a bulb, is used in the front fog
lamps. Contact a MITSUBISHI MOTORS
Authorized Service Point when there is a need for repair or replacement.Rear fog lamp
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip betweenthe bumper and the right edge of the
lamp unit (A), and then pry gently as
shown to remove it.
2. Turn the socket (B) anticlockwise to re-
move it, and then pull the bulb out of the
socket.
Replacement of lamp bulbs
10-262*$(20(1Maintenance10

3.To install the bulb, perform the removal
steps in reverse.NOTEz When installing the lamp unit, first insert the
tab (C) into the groove (D) on the body, and then push on the lamp unit to fit it into place.Rear combination lamps
1. Open the tailgate.
2. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the notch of the cover (A), and then pry gen-tly as shown to remove it.
3. Remove the screws (B) that hold the
lamp unit and remove the lamp unit.
4. Turn the socket and bulb assembly anti-
clockwise to remove it.
C- Stop lamp and tail lamp (LED) - can- not be replaced
D- Rear turn-signal lamp
NOTEz An LED, not a bulb, is used in the stop lamp
and tail lamp. Contact a MITSUBISHI
MOTORS Authorized Service Point when
there is a need for repair or replacement.
Replacement of lamp bulbs
10-272*$(20(1Maintenance10

5. Remove the bulb by pulling it out.
6.To install the bulb, perform the removal
steps in reverse.
NOTEz When mounting the lamp unit, align the
groove (E) on the lamp unit with the clip on
the body and the pin (F) on the unit with the
hole in the body.NOTETail lamps (on tailgate)NOTEz An LED, not a bulb, is used in the tail lamps
(on tailgate). Contact a MITSUBISHI
MOTORS Authorized Service Point when
there is a need for repair or replacement.Reversing lampsNOTEz An LED, not a bulb, is used in the reversing
lamps. Contact a MITSUBISHI MOTORS
Authorized Service Point when there is a need for repair or replacement.Licence plate lamps
1. When removing the lamp unit (A), push
it towards the left side of the vehicle
body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
Replacement of lamp bulbs
10-282*$(20(1Maintenance10

3. Remove the bulb by pulling it out.
4.To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lamp, insert tab (C) first
then align and insert tab (D).High-mounted stop lampNOTEz An LED, not a bulb, is used in the high-
mounted stop lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Masking the headlamps
When entering a country in which vehicles
are driven on the opposite side of the road to
the country in which your vehicles is sup- plied, necessary measures have to be taken toavoid dazzling oncoming traffic.
Mask the headlamps according to the next
procedure. 1. Turn the headlamp off and wait until the
headlamps got cold.
2. According to the illustrations, prepare
the sticker (A) to stick the headlamp sur- face of right and left.
NOTEz Use a sticker with a light blocking effect
enough.
Using of a sticker without a light blocking
effect will not acquire a blocking effect.3. Affix the sticker with its upper edge
positioned 10 mm above the central mark (B) on the headlamp and its leftand right edges aligned with the edges
(C) of the reflective surface.
Masking the headlamps
10-292*$(20(1Maintenance10 Left lens70 mm
30 mm 10 mm
Right lens 70 mm
10 mm 30 mm

2*$(20(1

Vehicle labelling................................................................................ 11-02
Vehicle dimensions............................................................................11-04
Vehicle performance..........................................................................11-06 Vehicle weight................................................................................... 11-06
Engine specifications........................................................................ 11-08
Electrical system............................................................................... 11-08
Tyres and wheels............................................................................... 11-09
CO 2 Mass Emissions......................................................................... 11-10
Capacity.............................................................................................11-116pecifications
2*$(20(111

Vehicle labelling
Vehicle identification number
The vehicle identification number is stamped on the bulkhead as shown in the illustration.
Vehicle information code plate
The vehicle information code plate is riveted as shown in the illustration.
The plate shows model code, engine model,
transmission model and body colour code, etc.
Please use this number when ordering re-
placement parts.
1- Model code
2- Engine model code
3- Transmission model code
4- Body colour code
5- Interior code
6- Option code
7- Exterior code
Vehicle labelling
11-022*$(20(1Specifications11