2020 MITSUBISHI ASX Owner's Manual (in English)

zAutomatic High-Beam (AHB)*CAUT,ONz To maintain proper performance of the
FCM, RMS, LDW and AHB;

Laser classification label
For Europe
For Moldova and Ukraine
For Israel

Laser explanatory label
Laser warning label
Forward Collision Mitigation system (FCM)*
6-582*$(20(1Starting and driving6

Radar sensing misacceleration Mitigation System (RMS) (Forward)*
The Radar sensing misacceleration Mitigation System (RMS) (Forward) operates to prevent sudden starts and mitigate collision-caused damages by suppressing the engine output for up to approximately 5 seconds when the system judges that the system is detected the vehicle or obstacleswithin approximately 4 m in front your vehicle and judges that accelerator pedal was depressed promptly and too strongly such as misoperation
of it. This system operates when the vehicle is at stop or moving forward at speed less than approximately 10 km/h (6 mph). When the RMS (Forward) operates, the
indicator blinks in the instrument cluster, and the buzzer sounds intermittently.

Following parts are used in combination with Forward Collision Mitigation system (FCM) and RMS (Forward).
For details, see these sections of this manual:
z Sensor
o p. 6-56
z FCM and Radar sensing misacceleration Mitigation System (RMS) (Forward) ON/OFF switch
o p. 6-54
z
indicator o p. 6-50
z
indicator o p. 6-54
SituationIndication lampBuzzerWhen an obstacle is detected in front of your
vehicle with the selector lever in the “D”
(DRIVE), “Ds” (DOWNSHIFT & SPORTY
DRIVING), “L” (LOW) or “M” (MANUAL)
position, if the accelerator pedal is depressed
promptly and too strongly, the engine output is
suppressed for up to approximately 5 seconds.
Blinks
Intermittent beeping sound
Radar sensing misacceleration Mitigation System (RMS) (Forward)*
6-592*$(20(1Starting and driving6

:ARN,NGzDo not overly rely on the RMS (Forward). It is never a substitute for your safe and careful driving. Always be careful to operate the accelerator
pedal perceiving the environmental conditions. Misoperation can lead to a serious accident.
z The RMS (Forward) does not have a brake function. Even if the system operates, the vehicle will start to creep if you do not depress the brake
pedal.
Depress the brake pedal according to the environmental condition.
z Depending on the situation, the system does not operate even if the vehicle or the obstacle id in front of your vehicle and this may cause the vehicle
to start suddenly and lead to a serious accident.
z If the vehicle is trapped in the railway crossing because the system is activated as the crossing barrier is misrecognised as an obstacle, escape from
the railway crossing without any panic by one of the following methods.

CAUT,ONzThe RMS (Forward) operates to the obstacles such as a vehicle ahead or a wall. It sometimes happens that a motorcycle, bicycle or pedestrian are detected as
obstacles, but these are not the object of the RMS (Forward).
z The RMS (Forward) may not operate in the following conditions.

CAUT,ONzThe RMS (Forward) may not operate because the sensor cannot detect the front vehicle or obstacle as follows.

CAUT,ONzTurn off the RMS (Forward) with the FCM and RMS (Forward)* ON/OFF switch beforehand when the vehicle is placed in any of the following situations
as the system can operate unexpectedly.

:ARN,NGzBefore using the BSW, read this entire
section to fully understand the limitationsof this system. Failure to follow instruc- tions could result in an accident.
z Never rely solely on the BSW system
when changing lanes. The BSW is an aid
only. It is not a substitute for your safe and careful driving. Always check visually
behind and all around your vehicle for other vehicles.
The performance of the BSW may vary
depending on driving, traffic and/or road conditions.Detection areas
The BSW uses two sensors (A) located inside
the rear bumper.
The detection areas are shown as illustrated.
:ARN,NGz In certain situations, the BSW may not
detect a vehicle in the detection areas or
the detection may be delayed. Some of these include: