2020 MITSUBISHI ASX Owner's Manual (in English)

Set-
tings
name
Settings ValueSettings content
TP-S OFFDo not automati-
cally search for
traffic messages
(TP stations).PI-SPI-S ONSearch for the
same station or
local station in
that registered in
the preset chan-
nel.PI-S OFFDo not search
for the same sta-
tion or local sta-
tion for that reg-
istered in the
preset channelPTYENGLISHSet the display
language for the
program content
search (PTY
search) to Eng-
lish.Set-
tings
name
Settings ValueSettings content
FRANdAISSet the display
language for the
program content
search (PTY
search) to
French.DEUTSCHSet the display
language for the
program content
search (PTY
search) to Ger-
man.SVENSKSet the display
language for the
program content
search (PTY
search) to Swed-
ish.ESPAfOLSet the display
language for the
program content
search (PTY
search) to Span-
ish.Set-
tings
name
Settings ValueSettings content
ITALIANOSet the display
language for the
program content
search (PTY
search) to Ital-
ian.CTCT ONUpdate the time
if time data is re-
ceived.CT OFFDo not update
the time even if
time data is re-
ceived.
*: It is necessary to press the [TP@ key and
turn traffic message standby mode “ON”.
Time Setting
Turning the RDS setting CT setting “CT OFF” enables manual setting of the time. 1. Select “YES” at the “Adjust time”
screen, and press the
/SEL key.
The hour can be adjusted. Press the
/SEL key again to adjust the minutes.
2. Turn the
/SEL key to adjust the time.
3. Press the
/SEL key.
This completes the adjustment.
System settings
7-412*$(20(1For pleasant driving7

NOTEzIn order to finish adjusting the time, hold
down the /SEL key until the seconds are
reset to “00”.
PHONE Settings
Change the mobile phone voice cut-in set-
tings and the Bluetooth

Set-
tings
name
Settings valueSettings content
PHONE IN-LDuring mobile
phone voice cut- in, output sound from the leftfront speaker.HFM voice lan-
guage
settingsENGLISHChange the hands free module voice
language.FRENCHGERMANSPANISHITALIANDUTCHPORTUGUESERUSSIANNOTEz Depending on the vehicle model, this may
not display.
Gracenote DB (Vehicles with a
Bluetooth

Troubleshooting
Please check these items if a message appears on the display, or if you think something is not working properly.If This Message Appears...
A message is displayed on this product according to the situation.
ModeMessageCauseResponseCDCHECK DISCThe disc is inserted upside down.Insert with the label side up.The disc has condensation on it.Wait a while before inserting again.DISC ERRORThe disc is damaged.Clean the read surface of the disc.The disc is dirty.INTERNAL EThe drive has malfunctioned for some reason.Check that there is no problem with the disc, and insert
the disc again. If the problem persists, consult a
MITSUBISHI MOTORS Authorized Service Point.HEAT ERRORThe temperature inside the product is high.Remove the disc, and wait for the internal temperature
to return to normal.USBFILE ERRORFiles that cannot be played are selected.Select files that can be played.

W “Audio Files (MP3/WMA/AAC)” on page 7-15USB BUS PWRThere is high or low electrical current or voltage.Turn the power OFF and wait a short while. If the prob-
lem persists, consult a MITSUBISHI MOTORS Author- ized Service Point.LSI ERRORThere is an internal malfunction for some reason.UNSUPPORTED FORMATUnsupported audio files have been played.Confirm audio files that can be played.
W “Audio Files (MP3/WMA/AAC)” on page 7-15UNSUPPORTED DEVICEAn unsupported USB device has been connected.Please connect a USB memory device.iPodNO SONGAn iPod/iPhone not containing any tracks has been
connected.Connect an iPod/iPhone containing tracks.
Troubleshooting
7-442*$(20(1For pleasant driving7

ModeMessageCauseResponseVER ERRORThis iPod/iPhone software version is not supported.Please change to a supported software version.OtherERROR DCAn abnormal direct voltage has been sent to the speak-
ers.Turn the power OFF and wait a short while. If the prob-
lem persists, consult a MITSUBISHI MOTORS Au- thorized Service Point.If You Think Something Is Not Working Properly...
Here is a list of symptoms, causes and responses if you think something is not working properly.
SymptomsCauseResponseThere is no sound or quiet
soundThe volume is turned to its minimum.Adjust the volume.

W “Adjust Volume” on page 7-20The balance or fader is turned to one side.Adjust the balance or fader.

W “Adjust Audio Quality and Volume Balance” on page 7-39The disc cannot be inserted.A disc is already in the product.Eject the disc.

W “Insert/Eject Discs” on page 7-20There is no disc in the product, but the product says it is
loading.Press the eject button once.

W “Insert/Eject Discs” on page 7-20The disc cannot be played.The disc is inserted upside down.Insert with the label side up.The disc has condensation on it.Wait a while before inserting.The disc is dirty.Clean the read surface of the disc.The sound skips in the
same place.The disc is damaged or dirty.Check the disc.There is no sound, even if
the disc is inserted.Damage to or dirt on the disc means that its data cannot be read.Check the disc. Additionally, if using CD-R/RW discs,
their characteristics may render them unable to be played.

Troubleshooting
7-452*$(20(1For pleasant driving7

Link System*
The Link System takes overall control of the devices connected via the USB input terminal
or the Bluetooth

NOTEzSome Bluetooth

HANG-UP button
zPress this button when an incoming call
is received to refuse the call.
z Press this button during a call to end the
current call.
When another call is on hold, you will switch to that call.
z If this button is pressed in the voice rec-
ognition mode, the voice recognition
mode will be deactivated.
NOTEz When you press the SPEECH button to enter
voice recognition mode with a cellular
phone paired to the system, current informa- tion on the cellular phone, such as “remain- ing battery life,” “signal strength” or “roam-
ing,” will be displayed on the audio dis-
play.*
*: Some cellular phones will not send this
information to the Bluetooth