2020 MITSUBISHI ASX Owner's Manual (in English)

In these situations, repeat the speed settingprocedure:
z The CRUISE CONTROL ON/OFF
switch is pressed.
z [Except vehicles equipped with keyless
operation system@
Turn the ignition switch to the “LOCK” or “ACC” position.
[Vehicles equipped with keyless opera-
tion system@
Put the operation mode in OFF or ACC.
z “CRUISE” indication lamp is turned
OFF.Forward Collision
Mitigation system (FCM)*
The Forward Collision Mitigation System (FCM) uses a sensor (A) to determine the
distance and relative speed to a vehicle and a pedestrian in front. When your vehicle is ap-
proaching a vehicle or a pedestrian straight- ahead in your path and the FCM judges that
there is the risk of a collision, the system gives audible and visual warnings (Forward
collision warning function), increases the
brake fluid pressure (FCM brake prefill func- tion), and also provides braking force assis-
tance when you depress the brake pedal (FCM brake assist function) to avoid frontalcollision.
When the risk of collision increases more, the
system causes the brakes to work moderately
to encourage you to apply brakes. If the sys- tem judges that a potential collision is immi- nent, it initiates emergency braking to miti-
gate collision-caused damages or to avoid possible collision (FCM braking function).Stop lamps are illuminated during automatic
braking.If you turn the FCM ON/OFF, the Radar
sensing misacceleration Mitigation System (RMS) (Forward) also turns ON/OFF at the same time. {Vehicles equipped with the RMS
(Forward)`
Forward Collision Mitigation system (FCM)*
6-492*$(20(1Starting and driving6

:ARN,NGzA driver is responsible for driving safely.
The FCM is the system to mitigate colli- sion- caused damages or to avoid colli- sions as much as possible.
The system is not intended to compensate for driver

zAgainst a vehicle: Approximately
15 km/h to 80 km/h.
z Against a pedestrian: Approximately
15 km/h to 65 km/h.CAUT,ONz The brake assist function may not be trig-
gered when the brake pedal is operated in certain ways.
Do not overly rely on the system; if your ve- hicle is in danger of collision, take all neces-
sary collision-evading actions, such as de-
pressing the brake pedal strongly regardless
of whether the system is activated or not.FCM braking function
If the system judges that there is a high risk
of your vehicle colliding with a vehicle or a pedestrian in front, the system applies the
brakes moderately to encourage you to apply the brakes.
If the system judges that a collision is un-
avoidable, it initiates emergency braking con- trol to mitigate collision-caused damages or,
if the situation permits, to avoid a collision. When the emergency braking control is trig- gered, you are warned of the hazard by a vis- ual alarm.
Once the emergency braking has worked, you
are alerted to this by a message on the infor- mation screen of the multi-information dis- play.
The FCM braking function operates at the
following vehicle speed:
z Against a vehicle: Approximately
5 km/h to 80 km/h
z Against a pedestrian: Approximately
5 km/h to 65 km/h
CAUT,ONz Do not use the FCM as a normal braking.
z After your vehicle has stopped following the
activation of the FCM, automatic braking is
released. As the vehicle will then start creep-
ing, be sure to depress the brake pedal to hold the vehicle stationary.
z When applying the brake during the auto-
matic braking condition the pedal will feel
firm.
This is not abnormal.
You can apply more pressure to the pedal to
assist in braking.
z In the following situations, the system pro-
vides neither control nor alarming.

CAUT,ON

CAUT,ON

NOTEzA sound will be heard during the activation
of automatic braking, this is a function of the brake control and is not abnormal.FCM and Radar sensing misac-
celeration Mitigation System(RMS) (Forward)* ON/OFFswitch
This switch is used to turn on and off the
FCM and RMS (Forward) and, also to select your desired collision alarm timing.
When the switch is held pressed, the
ON/OFF state of the FCM and RMS (For- ward) changes from ON to OFF and vice ver- sa. If you give the switch a short press with
the FCM in the ON state, you can change the collision alarm timing.
NOTEz When the FCM and RMS (Forward)*
ON/OFF switch is held pressed to change
the ON/OFF state of the FCM, the ON/OFF
state of the RMS (Forward) is also changed
at the same time.
To turn on/off the system
You can switch the system from OFF to ON
or ON to OFF if you hold the FCM and RMS (Forward)* ON/OFF switch pressed when the
ignition switch is turned to the “ON” position
or the operation mode is put in ON.
Once the system is turned on, the information screen of the multi-information display
shows the collision alarm timing currently se- lected, and the
indicator on the instrument
cluster goes out.
When you turn off the system, the following message appears on the information screen of
the multi-information display and the
indi-
cator will come on in the instrument cluster.
Cycling the ignition switch to the “ON” posi-
tion or putting the operation mode in ON will
set the FCM back ON.
NOTEz The indicator is combined with the Radar
sensing misacceleration Mitigation System
(RMS) (Forward) OFF indicator.
To change alarm timing
Give a short press to the FCM and RMS
(Forward)* ON/OFF switch to change the
timing at which the frontal collision alarm is
triggered. Every time you press the switch, the alarm timing changes from three levels
(far, middle or near).
As you make selection, the selected alarm
timing is displayed on the information screen
of the multi-information display. Even after turning off the FCM, turning the ignition
switch to the “LOCK” position or putting the operation mode in OFF, the system retains
your last selected alarm timing in memory.
Forward Collision Mitigation system (FCM)*
6-542*$(20(1Starting and driving6

Distance mode: FarDistance mode: MiddleDistance mode: NearCAUT,ONzFor the FCM brake prefill, the FCM brake
assist and the FCM braking functions, the function triggering timing cannot be changed.System problem warning
If there is a malfunction in the system, a
warning will appear on the information
screen of the multi-information display de- pending on the situation.
Windscreen is dirty
When the FCM system determines that its
performance has been degraded, the FCM will become inoperative.
This can occur when:
z Foreign objects, such as dirt, snow or
ice, adhere to the windscreen of the sen-
sor portion.
z There are adverse weather conditions,
such as rain, snow, sand storms, etc.
z A vehicle in front or an oncoming vehi-
cle is splashing water, snow or dirt.
The following message will appear on the in-
formation screen of the multi-information
display and the
indicator will come on in
the instrument cluster.
When the sensor performance returns, the FCM functions will resume operation.
If the display keeps showing the message,
there is a possibility that the sensor has a
malfunction. Contact a MITSUBISHI
MOTORS Authorized Service Point for in-
spection of the sensor.NOTEz The “CAMERA BLOCKED” message may
temporarily appear on the information
screen when the sensor cannot detect a vehi- cle, a pedestrian or an object within range.
This is not a malfunction. When a vehicle or an object comes within range, the FCM
function will resume and the message will go off.
z The “CAMERA BLOCKED” message may
appear on the information screen when driv-
ing on a nonbusy road with a few vehicles
and obstacles in front.
When the system cannot oper-
ate temporarily
If the system becomes temporarily unavaila-
ble for some reason, the following messagewill appear on the information screen of the
multi-information display, the
indicator
will come on in the instrument cluster and the
FCM will automatically be turned off.
Forward Collision Mitigation system (FCM)*
6-552*$(20(1Starting and driving6

If the display keeps showing the message,
there is a possibility that the FCM has a mal-
function. Contact a MITSUBISHI MOTORS
Authorized Service Point for inspection of the system.
Sensor is too hot or cold
If the system becomes temporarily unavaila- ble due to the high or low temperature of the
sensor, the following message will appear on the information screen of the multi-informa- tion display, the
indicator will come on in
the instrument cluster and the FCM will auto-
matically be turned off.
After the temperature of the sensor has been
in range, the system will automatically return
to operation.
If the display keeps showing the message,
there is a possibility that the FCM has a mal-
function. Contact a MITSUBISHI MOTORS
Authorized Service Point for inspection of
the system.
FCM deactivation due to fault
If the FCM detects a malfunction in the sys-
tem, either one of the following messages will appear on the information screen of themulti-information display, the
indicator
will come on in the instrument cluster and the
FCM will automatically be turned off.
If the message remains even after the ignition
switch is turned to the “LOCK” position and then turned back to the “ON” position or the
operation mode is put in OFF, and then turned back to “ON”, please contact a
MITSUBISHI MOTORS Authorized Service
Point.
NOTEz If the sensor or its surrounding area reaches
an extremely high temperature when parking the vehicle under a blazing sun, the “FCMSERVICE REQUIRED” message may ap-
pear.
After the temperature of the sensor or its sur-
rounding area has been in range, if the mes-
sage remains even after restarting the en- gine, please contact a MITSUBISHI
MOTORS Authorized Service Point.Handling of the sensor
The sensor (A) is located inside the wind-
screen as shown in the illustration.
The sensor is shared in the following sys-
tems:
z Forward Collision Mitigation system
(FCM)*
z Radar sensing misacceleration Mitiga-
tion System (RMS) (Forward)*
z Lane Departure Warning (LDW)*
Forward Collision Mitigation system (FCM)*
6-562*$(20(1Starting and driving6