2016 Peugeot 308 Owner's Manual

167
308_en_Chap06_conduite_ed02-2015
Automatic operation
Never select position N while the
vehicle is moving.
Never select positions P or R unless the
vehicle is completely stationary.
Sport and snow programmes
these two special programmes supplement the
a utomatic operation in very specific conditions
of use.
S appears in the instrument panel.
Snow "T"
F Press the " T" s witch, after starting the
engine.
the g

earbox adapts to driving on slippery
roads.
thi

s programme improves starting and drive
when traction is poor. T appears in the instrument panel.
Return to automatic operation
F At any time, press the button selected
(
S or " T") again at any time to quit the
programme engaged and return to auto-
adaptive mode.
Creep function (moving
without using the
accelerator)
this function provides great flexibility in
m anoeuvring the vehicle at low speed (when
parking, in traffic jams, …).
With the engine at idle, parking brake released
and position D , M or R selected, the vehicle
moves
a

s soon as you take your foot off
the brake pedal (even without pressing the
accelerator).
For your safety, this function will be activated
only if you press the brake pedal when
changing from forward drive to reverse.
It is deactivated on opening the driver's door.
Closing the door then pressing the brake or
accelerator pedal, reactivates the function.
Never leave children inside the vehicle
without supervision when the engine is
running.
If you vehicle is equipped with the "Dynamic
function", refer to the section covering this,
which is part of sport mode.
F
Selec

t position D for automatic
changing
of the six gears.the g
earbox then operates in auto-adaptive
mode, without any intervention on the part
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
vehicle.
For maximum acceleration, without touching
the gear selector press the accelerator pedal
down fully (kick-down).
the g

earbox changes
down automatically or maintains the gear
selected until the maximum engine speed is
reached.
On braking, the gearbox changes down
automatically to provide efficient engine
braking.
If you release the accelerator sharply, the
gearbox will not change to a higher gear for
safety reasons.Sport "S"
F Press the "S" s witch, after starting the engine.the g
earbox automatically favours a dynamic style
of driving.
6
Driving

168
308_en_Chap06_conduite_ed02-2015
F Select position M for sequential c hanging
of the six gears.
F
Pu

ll towards the + sign and release to
change up a gear.
F
Pu

sh towards the - sign and release to
change down a gear.
It is only possible to change from one gear to
another if the vehicle speed and engine speed
permit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears
engaged appear in succession in the
instrument panel.
If the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D
(automatic) to position M (manual) at any time.
When the vehicle is stationary or moving
very slowly, the gearbox selects gear M1
automatically.
the s

port and snow programmes do not
operate in manual mode.
Manual operation
Invalid value during manual
operation
this symbol is displayed if a gear is
n ot engaged correctly (gear selector
between two positions).
Stopping the vehicle
If the selector lever is not in position P ,
when the driver's door is opened or
approximately 45 seconds after the
ignition is switched off, there is an
audible signal and a message appears.
F
Re

turn the selector lever to
position
P ; t

he audible signal stops
and the message disappears. When the ignition is on, a message
appears in the instrument panel
screen to indicate a gearbox fault.
Operating fault
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P
to R and from N to R
.
thi

s will not cause any
damage to the gearbox.
Do not exceed 60 mph (100 km/h), local speed
restrictions permitting.
Have it checked by a P
eu

ge
Ot d
ealer or a
qualified workshop.
Before switching off the engine, you can
engage position P or N to place the gearbox in
neutral.
In both cases, apply the parking brake to
immobilise the vehicle, unless it is programmed
to automatic mode. You risk damaging the gearbox:
-
if y

ou press the accelerator and
brake pedals at the same time,
-
if y

ou force the lever from position
P

to another position when the
battery is flat.
to re

duce fuel consumption when
stationary for long periods with the
engine running (traffic jam...), position
the selector lever at N and apply the
parking brake, unless it is programmed
in automatic mode.
Driving

169
308_en_Chap06_conduite_ed02-2015
Dynamic pack
this pack conditions:
- th e visual ambience, with specific back-
lighting for the instrument panel,
-
th

e acoustic ambience of the engine,
-
th

e power assistance for the steering,
-
a

cceleration,
-
in

formation to the driver in the instrument
panel on dynamic settings.
thi

s function is only available when
Park Assist is not selected and snow
mode in the automatic gearbox is not
selected.
If Park Assist
i

s switched on, this
automatically deactivates the function.
Activation
F Press the end of the wiper control stalk to
d isplay in the instrument panel the different
information on dynamic settings.
the

telemetry data (longitudinal and
lateral acceleration, power produced,
turbocharger pressure, ...) are given as
an indication only.
F Pr
ess and hold the button until the back-
lighting in the instrument panel changes.
the LeD in t

he button stays on.
Display
F Press repeatedly to go from one screen to
a nother.
If the L
eD fl

ashes, activation is not
possible (for example if Park Assist
or snow mode is selected) and so
the back-lighting returns to its normal
mode.
If the L
eD co

ntinues flashing for a long
time, contact a P
eu

ge
Ot d

ealer or a
qualified workshop.
With an automatic gearbox, gear
changes are faster.
6
Driving

170
308_en_Chap06_conduite_ed02-2015
Stop & Start
Operation
Going into engine STOP mode
the "ECO" warning lamp comes on
in the instrument panel and the engine
goes into standby automatically:
-
Wi

th a manual gearbox , at speeds below
12 mph (20 km/h) or vehicle stationary
(depending on the engine), when you place
the gear lever in neutral, and you release
the clutch pedal.
Never refuel with the engine in S
tOP
m

ode; you must switch off the ignition
with the button. For your comfort, during parking
manoeuvres, S
tOP m
ode is not
available for a few seconds after
coming out of reverse gear.
S
tOP m

ode does not affect the
functionality of the vehicle, such as for
example, braking, power steering...
A slight delay between the vehicle
stopping and the engine cutting out may
be noticed.
Special cases: STOP mode not
available
StOP mode is not invoked principally when:
- th e vehicle is on a steep slope (up or down),
-
the

driver's door is open,
-
th

e driver's seat belt is not fastened,
-
th

e vehicle has not exceeded 6 mph
(10
k

m/h) since the last engine start by the
driver,
-
th

e electric parking brake is applied or
being applied,
-
th

e engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-
dem

isting is active,
-
som

e special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.
If your vehicle is fitted with Stop & Start,
a time counter calculates the time spent
in S
tOP m

ode during a journey.In this case, the "ECO" warning
lamp flashes for a few seconds then
goes
o

ff.
This operation is perfectly normal.
the S

top & Start
s

ystem puts the engine temporarily into standby - S
tOP m

ode - during stops in the traffic (red lights, traffic jams, or other...).
the e

ngine restarts automatically - S
tARt m

ode - as soon as you want to move off.
the r

estart takes place instantly, quickly and
silently.
Per fect for urban use, the Stop & Start system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.
Stop & Start time
counter
(minutes / seconds or hours / minutes) -
Wi
th an automatic gearbox
, vehicle
stationary, when you press the brake
pedal or place the gear selector lever in
position
N .
I
t resets to zero every time the ignition is
switched on.
Driving

171
308_en_Chap06_conduite_ed02-2015
Going into engine START mode
the "ECO" w arning lamp goes off
and the engine starts automatically:
-
Wi

th a manual gearbox , when you fully
depress the clutch pedal. StARt m
ode is invoked automatically
when:
Special cases: START invoked
automatically
- you open the driver's door,
- you unfasten the driver's seat belt,
-
th

e speed of the vehicle exceeds 15 mph
(25 km/h) or 2 mph (3 km/h) (depending on
the engine) with a manual gearbox,
-
th

e speed of the vehicle exceeds 2 mph
(3
k

m/h) with an automatic gearbox,
-
th

e electric parking brake is being applied,
-
som

e special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system. If the system has been deactivated
in S
tOP m

ode, the engine restarts
immediately.
At any time, press the "ECO OFF" switch to
deactivate the system.
thi

s is confirmed by the switch warning lamp
coming on accompanied by a message.
Deactivation / Reactivation
In this case the "ECO" warning lamp
flashes for a few seconds, then goes
of f.
This operation is perfectly normal.
-
Wi

th an automatic gearbox
:
●
ge

ar selector in position D or M
, when
you release the brake pedal,
●
or g

ear selector in position N and brake
pedal released, when you place the gear
selector in position D or M ,
●
or w

hen you engage reverse.
the s

ystem is reactivated automatically
at every new engine start by the driver.
Press the "ECO OFF" switch again.
the s

ystem is active again; this is confirmed
by the switch warning lamp going off,
accompanied by a message.
6
Driving

172
308_en_Chap06_conduite_ed02-2015
Operating fault
In the event of a fault with the system, this
warning lamp comes on continuously.
Have it checked by a P
eu
ge
Ot d
ealer or a
qualified workshop.
In the event of a fault in S
tOP m

ode, the
vehicle may stall.
All of the instrument panel warning lamps
come on.
Depending on version, an alert message may
also be displayed, asking you to place the gear
lever in position N and put your foot on the
brake pedal.
You must switch off the ignition, then start the
engine again. Before doing anything under the
bonnet, deactivate the Stop & Start
system to avoid any risk of injury
resulting from automatic operation of
S
tA

R
t m o
d e .
thi

s system requires a 12 V battery with a
special specification and technology (reference
numbers available from P
eug
e
Ot de
alers).
Fitting a battery not listed by P
eu
ge
Ot
i
ntroduces the risk of malfunction of the
system.
For charging, use a 12 V charger and do not
reverse the polarity.
Maintenance
the Stop & Start system makes use of
a dvanced technology. For any work on
the system go to a qualified workshop
with the skills and equipment required,
which a P
eu

ge
Ot d
ealer is able to
provide.
Driving

173
308_en_Chap06_conduite_ed02-2015
Memorising speeds
Memorising
this function allows speeds to be saved, which can then be offered to set the two systems: the speed limiter (to limit the speed of the vehicle) or the
c ruise control (for a vehicle cruising speed).
You can memorise up to six speed settings for each of the two systems. By default, some speed settings are already memorised.
F
Selec

t the "Driving assistance " menu.
For safety reasons, the driver must
carry out these operations when
stationary. F
Se

lect the system for which you want to
memorise new speed settings:
thi

s function is accessible in the touch screen.
F


e
nt
er the new value using the numerical
keypad and confirm.
F
Co

nfirm to save the modification and quit
the menu.
●
sp

eed limiter
or
F
Pr

ess the button corresponding to the
speed setting you want to modify.
thi

s button allows you to restore the
factory settings.
Touch screen
F In the secondary page, press
" S
peed settings ".
●
cr

uise control.
6
Driving

174
308_en_Chap06_conduite_ed02-2015
Steering mounted controls
6. Speed limiter on / pause indication.
7. Speed limiter mode selection indication.
8.
Speed

value setting.
Speed limiter "LIMIt"
System which prevents the vehicle from exceeding the speed programmed by the driver.
the speed limiter cannot, in any
c ircumstances, replace the need to observe
speed limits, nor can it replace the need for
vigilance on the part of the driver.
Once the programmed speed limit is reached,
additional pressure on the accelerator pedal
has no effect.
1.
Selec

t speed limiter mode.
2.
Dec

rease programmed speed.
3.
Inc

rease programmed speed.
4.
Sp

eed limiter on / pause.
5.
Di

splay the list of memorised speeds.Displays in the instrument panel
S witching on the speed limiter requires
a programmed speed of at least 20 mph
(30
k

m/h).
the s

peed limiter is paused by operation of the
control.
the

programmed speed can be exceeded
temporarily by pressing the accelerator firmly
beyond the point of resistance.
to re

turn to the programmed speed, simply
release the accelerator pedal until the vehicle
returns to the programmed speed limit.
the p

rogrammed speed remains in the
memory when the ignition is switched off. For more information on memorising speeds,
refer to the corresponding section.
Driving