2014 FORD MONDEO Owners Manual

Downloaded from www.Manualslib.com manuals search engine WARNINGS
Do not place objects on the liftgate.
Make sure you fully close the liftgateafter operation.
Operate the liftgate only when yourvehicle is stationary.
You can operate the liftgate using theremote control, the center console switch,the liftgate switch or the liftgate releasehandle.
Note:Make sure there is enough headroomto open the liftgate.
Note:If your vehicle has an automatictransmission, make sure the transmissionselector lever is in park.
Note:In extreme weather conditions,automatic opening and closing will not workwith the liftgate frozen to the seal.
Note:The liftgate will stop automaticallywhile opening and reverse some distance ifthere is an obstacle in the way.
Note:The liftgate will stop automaticallywhile closing and fully open if there is anobstacle in the way.
Note:You can manually operate theliftgate.
Liftgate Switch
Remote Control and Center ConsoleSwitch
Note:Switch the ignition on to operate theliftgate using the center console switch.
You will hear three chimes when theliftgate begins to close.
Five short chimes indicate a malfunctionwith the open or close request. This couldbe caused by one of the following:
•You switch the ignition on and thetransmission selector lever is not inpark.
•The battery voltage is below theminimum operating voltage.
•Your vehicle speed exceeds 3 mph (5km/h).
To open a fully closed liftgate, you caneither:
•Press the button on the remote controltwice within three seconds.
•Press the center console switch.
•Use the liftgate release handle.
To fully open a partially opened liftgate,you can either:
•Press the button on the remote controltwice within three seconds.
•Press the center console switch or theliftgate switch.
•Use the liftgate release handle.
To stop the liftgate, you can either:
•Press the button on the remote control.A further remote control operation willbe delayed for approximately threeseconds.
•Press the center console switch or theliftgate switch.
•Use the liftgate release handle.
47Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks

Downloaded from www.Manualslib.com manuals search engine Closing the Liftgate
WARNING
The bounce-back feature will notwork and it will not detect obstacleswhen the liftgate is in contact withthe vehicle body.
Note:Do not leave a passive key in yourvehicle when closing the liftgate. A messagewill be shown in the display. SeeInformation Messages (page 96).
Note:A recessed grip is located inside theliftgate to help with closing.
You can either:
•Press the button on the remote controltwice within three seconds.
•Press the center console switch or theliftgate switch.
•Use the liftgate release handle.
•Manually close the liftgate
The liftgate will close automatically whenit comes into contact with the vehicle body.
Programming the Liftgate
1.Open the liftgate.
2.Manually move the liftgate to the newrequired position.
3.Press and hold the liftgate switch forat least three seconds. You will hear achime.
KEYLESS ENTRY
General Information
The system will not function if:
•Your vehicle battery has no charge.
•The passive key frequencies arejammed.
•The passive key battery has no charge.
Note:If the system does not function, youwill need to use the key blade to lock andunlock your vehicle.
The system allows you to operate yourvehicle without the use of a key or remotecontrol.
Passive locking and unlocking requires avalid passive key to be located within oneof the three external detection ranges.These are located approximately 3.3 ft(1 m) from the front door handles and theliftgate.
Note:The system may not function if thepassive key is close to metal objects orelectronic devices, for example keys or a cellphone.
48Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks

Downloaded from www.Manualslib.com manuals search engine Passive Key
Your vehicle can be locked and unlockedwith the passive key. You can use thepassive key as a remote control. SeeLocking and Unlocking (page 44).
Locking Your Vehicle
Locking sensors are located on each of thefront doors.
For central locking and to arm the alarm,touch a locking sensor once.
For double locking and to arm the alarm,touch a locking sensor twice within threeseconds.
Note:Your vehicle does not automaticallylock. If you do not touch a locking sensoryour vehicle will remain unlocked.
Note:When locking your vehicle, do notgrip the door handle.
Note:Keep the door handle surface cleanto make sure the system operates correctly.
Note: Your vehicle will remain locked forapproximately three seconds. When thedelay period is over, you can open the doorsagain, provided the passive key is within therespective detection range.
Two short flashes of the directionindicators confirms that all the doors andthe liftgate have been locked and that thealarm has been armed.
Liftgate
Note:The liftgate cannot be closed andwill reopen if the passive key is locatedinside the luggage compartment with thedoors locked.
Note:If a second valid passive key islocated within the liftgate detection range,the liftgate can be closed.
Unlocking Your Vehicle
One long flash of the direction indicatorsconfirms that all the doors and the liftgatehave been unlocked and that the alarmhas been disarmed.
Note:When your vehicle remains lockedfor longer than three days, the system willenter an energy-saving mode. This is toprevent the vehicle battery running out ofcharge. When your vehicle is unlocked whilein this mode, the reaction time of the systemmay be a little longer than normal. To exitthe energy-saving mode, unlock yourvehicle.
Note:A valid passive key must be locatedwithin the detection range of that door.
Unlocking Only the Driver Door
You can program the system so that onlythe driver door is unlocked. See RemoteControl (page 32).
If the unlocking function is reprogrammedso that only the driver door is unlocked thefollowing will occur:
•If the driver door is the first dooropened, all the other doors will remainlocked. All the other doors can beunlocked from inside your vehicle bypressing the unlock button. The otherdoors can be unlocked individually bypulling the interior door handle on therespective door.
•If the front passenger door is the firstdoor opened, all the doors will beunlocked.
49Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks

Downloaded from www.Manualslib.com manuals search engine Disabled Passive Keys
Any keys left inside your vehicle interiorwhen it is locked will be disabled.
You cannot use a disabled key to switchthe ignition on or start the engine.
You must enable all passive keys again inorder to use them.
To enable all your passive keys, unlock yourvehicle using a passive key that has notbeen disabled or the remote controlunlocking function.
All passive keys will then be enabled if youswitch the ignition on or you start yourvehicle with a valid key.
Locking and Unlocking the Doorswith the Key Blade
Slide the release on the back of the remotecontrol and pivot the cover off to accessthe key blade.
Note:Only the driver door handle has a lockcylinder.
50Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingLocks

Downloaded from www.Manualslib.com manuals search engine PASSIVE ANTI-THEFT
SYSTEM
Principle of Operation
The system prevents someone fromstarting the engine with an incorrectlycoded key.
Note:Do not leave correctly coded keys inthe vehicle. Always take your keys and lockall doors when leaving the vehicle.
Coded Keys
If you lose a key, you can obtain areplacement from an authorized dealer. Ifpossible, provide them with the keynumber from the tag provided with theoriginal keys. You can also obtain extrakeys from an authorized dealer.
Note:Have all of your remaining keyserased and recoded if you lose a key. Havereplacement keys coded together withrecoding your remaining keys. See anauthorized dealer for further information.
Note:Do not shield your keys with metalobjects. This may prevent the receiver fromrecognizing a coded key.
Arming the Engine Immobilizer
When you switch the ignition off the engineimmobilizer will arm automatically after ashort time.
Disarming the Engine Immobilizer
When you switch the ignition on the engineimmobilizer will disarm automatically if acorrectly coded key is used.
If you are unable to start your vehicle witha correctly coded key, have your vehiclechecked by an authorized dealer.
ANTI-THEFT ALARM -
VEHICLES WITH: INTERIOR
SENSOR
Alarm System
WARNING
Do not arm the alarm with full guardif passengers, animals or othermoving objects are inside yourvehicle.
Perimeter Alarm
The perimeter alarm is a deterrent againstunauthorized access to your vehiclethrough the doors and the hood. It alsoprotects the audio unit.
Interior Sensors
The interior lamp unit sensors are locatedin the overhead console.
Note:Do not cover up the interior lamp unitsensors.
The sensors act as a deterrent againstunauthorized intrusion by sensing anymovement inside your vehicle.
Triggering the Alarm
Once armed, the alarm is triggered in anyof the following ways:
•If someone opens a door, the liftgateor the hood without a valid key orremote control.
•If someone removes the audio unit ornavigation system.
•If you switch your vehicle on without acorrectly coded key.
•If the interior sensors detect movementwithin your vehicle.
If the alarm is triggered, the alarm horn willsound for 30 seconds and the hazardwarning flasher will flash for five minutes.
51Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingSecurity

Downloaded from www.Manualslib.com manuals search engine Any further attempts to perform one of theabove will trigger the alarm again.
Full and Reduced Guard
Full Guard
Full guard is the standard setting.
In full guard, the interior sensors are onwhen you arm the alarm.
Reduced Guard
In reduced guard, the interior sensors areoff when you arm the alarm.
Selecting Full or Reduced Guard
You can select full or reduced guard usingthe information display. See GeneralInformation (page 86).
Ask on Exit (If Equipped)
You can set the information display to askyou each time which level of guard youwish to set.
Using the information display controls, scroll to:
Action and DescriptionMessage
Press the OK button.Settings
Press the OK button.Vehicle settings
Press the OK button.Alarm
Press the OK button.Ask on exit
Appears in the information display each time you switch yourvehicle off.Reduced guard
If you wish to arm the alarm with reduced guard, press theOK button when this message appears.If you wish to arm the alarm with full guard, leave your vehiclewithout pressing the OK button.
Note:Selecting reduced guard does not set the alarm permanently to reduced guard. Itsets it to reduced guard only for the current locking cycle.
Arming the Alarm
To arm the alarm, lock your vehicle. SeeLocks (page 44).
Disarming the Alarm
Vehicles Without Keyless Entry
Disarm and silence the alarm by unlockingthe doors with the key and switching yourvehicle on with a correctly coded key orunlocking the doors with the remotecontrol.
52Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingSecurity

Downloaded from www.Manualslib.com manuals search engine Vehicles with Keyless Entry
Note:A valid passive key must be locatedwithin the detection range of that door forkeyless entry. See Keyless Entry (page 48).
Disarm and silence the alarm by unlockingthe doors and switching your vehicle on orunlocking the doors with the remotecontrol.
ANTI-THEFT ALARM -
VEHICLES WITH: INTEGRAL
BATTERY
Alarm System
WARNING
Do not arm the alarm with full guardif passengers, animals or othermoving objects are inside yourvehicle.
Perimeter Alarm
The perimeter alarm is a deterrent againstunauthorized access to your vehiclethrough the doors and the hood.
Interior Sensors
The interior lamp unit sensors are locatedin the overhead console.
Note:Do not cover up the interior lamp unitsensors.
The sensors act as a deterrent againstunauthorized access by sensing anymovement within your vehicle.
Battery Back-up Sounder
The battery back-up sounder is anadditional alarm system, which sounds asiren if your vehicle battery or the batteryback-up sounder is disconnected. Whenyou lock your vehicle the system is armed.The sounder has its own battery and willsound an alarm siren even if someonedisconnects your vehicle battery or thebattery back-up sounder itself.
Triggering the Alarm
Once armed, the alarm is triggered in anyof the following ways:
•If someone opens a door, the liftgateor the hood without a valid key orremote control.
•If someone removes the audio ornavigation system.
•If you switch your vehicle on without acorrectly coded key.
•If the interior sensors detect movementwithin your vehicle.
•On vehicles with a battery back-upsounder, if someone disconnects yourvehicle battery or the battery back-upsounder itself.
If the alarm is triggered, the alarm horn willsound for 30 seconds and the hazardwarning flasher will flash for five minutes.
Any further attempts to perform one of theabove sounds the alarm again.
Full and Reduced Guard
Full Guard
Full guard is the standard setting.
In full guard, the interior sensors are onwhen you arm the alarm.
Reduced Guard
In reduced guard, the interior sensors areoff when you arm the alarm.
53Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingSecurity

Downloaded from www.Manualslib.com manuals search engine Selecting Full or Reduced Guard
You can select full or reduced guard usingthe information display. See GeneralInformation (page 86).
Ask on Exit (If Equipped)
You can set the information display to askyou each time which level of guard youwish to set.
Using the information display controls, scroll to:
Action and DescriptionMessage
Press the OK button.Settings
Press the OK button.Vehicle settings
Press the OK button.Alarm
Press the OK button.Ask on exit
Appears in the information display each time you switch yourvehicle off.Reduced
If you wish to arm the alarm with reduced guard, press theOK button when this message appears.If you wish to arm the alarm with full guard, leave your vehiclewithout pressing the OK button.
Note:Selecting reduced guard does not set the alarm permanently to reduced guard. Itsets it to reduced guard only for the current locking cycle.
Arming the Alarm
To arm the alarm, lock your vehicle. SeeLocks (page 44).
Disarming the Alarm
Vehicles Without Keyless Entry
Perimeter Alarm
Disarm and silence the alarm by unlockingthe doors with the key and switching yourvehicle on with a correctly coded key orunlocking the doors with the remotecontrol.
Category One Alarm
Disarm and silence the alarm by unlockingthe doors with the key and switching yourvehicle on with a correctly coded key within12 seconds or unlocking the doors with theremote control.
Vehicles with Keyless Entry
Note:A valid passive key must be locatedwithin the detection range of that door forkeyless entry. See Keyless Entry (page 48).
Perimeter Alarm
Disarm and silence the alarm by unlockingthe doors and switching your vehicle on orunlocking the doors with the remotecontrol.
54Mondeo (CNG) Vehicles Built From: 08-09-2014 Vehicles Built Up To: 19-04-2015, CG3633en enGBR, Edition date: 10/2014, First PrintingSecurity