2013 RENAULT KANGOO Petrol V42 Injection Workshop Manual

17B-33
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF028
CONTINUED
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3CT between components 195 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for +12 V or +9 V (for Duster) on connection 3FB of component 195.
If there is no +12 V or +9 V (for Duster), check the continuity of the following connection:
–3FB between components 1047 (for Logan, Sandero, Duster) or 238 (for Thalia 2/Symbol 2, Kangoo VLL)
or 983 (for Clio II F 6) and 195.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

17B-34
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF029
PRESENT OR
STOREDCYLINDER 4 INJECTOR CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 4 injector, component code 196.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 4 injector, component code196 between connections3FB and 3CU.
If the resistance measured is not between 11   X  20  (K4M, D4D engines), 11.5   X  12.5  (F4R engine),
9.2   X  17  (K7M engine) or 14   X  15  (K4M engine on Duster): replace the cylinder 4 injector,
component code 196 (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting
).
Run command AC008 Cylinder 4 injector and check the operation of the injector with a listening test.
V42_V04_DF029/ V42_V05_DF029/V42_V06_DF029/V42_V14_DF029/V42_V16_DF029/V42_V18_DF029

17B-35
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF029
CONTINUED
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3CU between components 196 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check for +12 V or +9 V (for Duster) on connection 3FB of component 196.
If there is no +12 V or +9 V (for Duster), check the continuity of the following connection:
–3FB between components 1047 (for Logan, Sandero, Duster) or 238 (for Thalia 2/Symbol 2, Kangoo VLL)
or 983 (for Clio II F 6) and 196.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

17B-36
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF038
PRESENT OR
STOREDCOMPUTER1.DEF: Internal electronic fault.
NOTESSpecial notes:
The OBD and Level 2 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Contact the Techline.
V42_V04_DF038/ V42_V05_DF038/V42_V06_DF038/V42_V14_DF038/V42_V16_DF038/V42_V18_DF038

17B-37
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF046
PRESENT OR
STOREDBATTERY VOLTAGE1.DEF: Battery voltage too low.
2.DEF: Battery voltage too high.
NOTESNone.
See Technical Note 6520 "Landi Renzo Euro V LPG system fault finding" (D4F734 engine on Logan and
Sandero) or Technical Note 6524 "Landi Renzo Euro V LPG system fault finding" (K4M616 engine on
Duster).
V42_V18_DF046

17B-38
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF047
PRESENT OR
STOREDCOMPUTER SUPPLY VOLTAGE1.DEF: Permanent high signal.
2.DEF: Permanent low level.
NOTESSpecial notes:
The OBD and Level 1 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Move the wiring harness between the injection computer, component code 120 and the battery, component code
107 to see if the status changes (Present Stored).
Look for any damage to the wiring harness and check the connection and condition of the battery, component code
107 and its connections.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Start the engine and check the battery voltage using PR071 Computer supply voltage is X  9V.
Stop the engine and check the charging circuit of the vehicle (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 16A,
Starting – Charging, Charging circuit: Checking).
If the fault is still present, contact the Techline.
V42_V04_DF047/ V42_V05_DF047/V42_V06_DF047/V42_V14_DF047/V42_V16_DF047/V42_V18_DF047

17B-39
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF050
PRESENT OR
STOREDBRAKE SWITCH CIRCUIT
1.DEF: Inconsistent signal.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present after the ignition has been switched on and the brake pedal has
been depressed.
The fault appears after a fault on one of the two brake switch contacts.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
With the brake pedal released, check ET039 Brake pedal and ET799 Brake wire contact.
ET039 must be Released and ET799 Inactive.
Check the fitting and mechanical operation of the brake pedal (the pedal returns properly).
If the check is incorrect, check the braking system.
Remove the brake pedal switch, component code 160 (see MR 388 (Logan and Sandero), MR 451 (Duster), MR
423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal
- Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A, Mechanical component controls,
Brake pedal: Removal - Refitting) and, without depressing the pedal, press sufficiently on the brake pedal switch
to seat it completely in its position.
Lock it by turning it an eighth of a turn.
With the brake pedal depressed, measure the resistance of the brake pedal switch, component code 160 between
connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL) and
65A. The value must be X > 10 M (between 0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls,
Brake pedal switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Brake pedal: Removal - Refitting).
With the brake pedal released, measure the resistance of the brake pedal switch, component code 160 between
connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL) and
5A, the value must be between 0  < X  1  (between 0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls,
Brake pedal switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Brake pedal: Removal - Refitting).
V42_V04_DF050/ V42_V05_DF050/V42_V06_DF050/V42_V14_DF050/V42_V16_DF050/V42_V18_DF050

17B-40
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF050
CONTINUED
Check the brake pedal switch connector, component code 160 (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Brake pedal switch: Removal - Refitting).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring
Check fuse F03 (for Logan, Sandero, Duster), F4 (for Thalia 2/Symbol 2, Clio II F 6 or F16 (for Kangoo VLL)
and replace it if necessary.
Checking the brake pedal switch:
After the repair, perform these two checks.
With the brake pedal released, check ET039 and ET799.
ET039 must be Released and ET799 must be Inactive.
While depressing the brake pedal, check ET039 and ET799.
ET039 must be Depressed and ET799 must be Active.
The two checks must be correct.
If the fault is still present, contact the Techline.