2012 Lexus CT200h Owner's Manual (in English)

5
615
5-2. Steps to take in an emergency
When trouble arises
CT200h_OM_OM76067E_(EE)Remove the center auxiliary
box.
Take out the emergency tire
puncture repair kit.
Taking out the jack
Remove the center deck board and center auxiliary box.
(See “Taking out the emergency tire puncture repair kit” for
details.)
Remove the hook and then
loosen and take out the jack.
For loosening
For tightening
When storing the jack, put it
into the tray and tighten it until
fixed to the tray.
Use of the jack: P. 6 0 2
STEP2
STEP3
STEP1
STEP2

616
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)
Before performing emergency repair
Check the degree of the tire damage.
A tire should only be repaired
with the emergency tire punc-
ture repair kit if the damage is
caused by a nail or screw pass-
ing through the tire tread.
• Do not remove the nail or
screw from the tire. Remov-
ing the object may widen the
opening and disenable emer-
gency repair with the kit.
• To avoid sealant leakage,
move the vehicle until the
area of the puncture, if
known, is positioned at the
top of the tire.

5
617
5-2. Steps to take in an emergency
When trouble arises
CT200h_OM_OM76067E_(EE)
Emergency repair method
Pull the insertion key out of the
kit.
Place the kit with the bottom
facing upward.
Peel off the label, and push in
the insertion key until a click is
heard.
Return the kit to an upright
position and make sure that the
compressor switch is off.
Use the kit with the top facing
upward.
Connect the power plug to the
power outlet socket. (P. 460)
STEP1
STEP2
STEP3
STEP4

618
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)Remove the valve cap from the
valve of the punctured tire.
Remove the air release cap
from the hose.
Connect the hose to the valve.
Screw the end of the hose
clockwise as far as possible.
Check the specified tire infla-
tion pressure.
Tire inflation pressure is speci-
fied on the label as shown. (P.
661)
Start the hybrid system. (P. 198)
STEP5
STEP6
STEP7
STEP8
STEP9

5
619
5-2. Steps to take in an emergency
When trouble arises
CT200h_OM_OM76067E_(EE)To inject the sealant and inflate
the tire, turn the compressor
switch on.
Use the kit with the top facing
upward.
Inflate the tire until the recom-
mended pressure is reached.
The sealant will be injected
and the pressure will spike
to 300 kPa (3.0 kgf/cm
2
or bar, 44 psi) or 400 kPa
(4.0 kgf/cm2 or bar, 58 psi),
then gradually decrease.
The air pressure gauge will
display the actual tire infla-
tion pressure about 1 minute
after the switch is turned on.
• Turn the compressor switch
off and then check the tire
inflation pressure. Being
careful not to over inflate,
check and repeat the infla-
tion procedure until the rec-
ommended tire inflation
pressure is reached.
STEP10
STEP 11

620
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)
• If the needle of the air pres-
sure gauge reaches the red
zone (450 kPa [4.5 kgf/cm
2
or bar, 65 psi] or more),
there may be a malfunction
in the tire or in the kit itself.
Stop operation immediately.
• If the tire inflation pressure
is still lower than the recom-
mended level after inflation
for 10 minutes with the
switch on, the tire is too
damaged to be repaired.
Turn the compressor switch
off and contact any autho-
rized Lexus dealer or
repairer, or another duly
qualified and equipped pro-
fessional.
• If the tire inflation pressure
exceeds the recommended
level, let out some air to
adjust the tire inflation pres-
sure.
(P. 624)
Disconnect the hose from the valve on the tire and then pull
out the power plug from the power outlet socket.
To spread the liquid sealant evenly within the tire, immedi-
ately drive for about 5 km (3 miles).STEP 12
STEP 13

5
621
5-2. Steps to take in an emergency
When trouble arises
CT200h_OM_OM76067E_(EE)After driving for about 5 km
(3 miles), stop your vehicle in a
safe place on a hard, flat surface
and reconnect the compressor.
Turn the compressor switch on
and wait for several seconds,
then turn it off. Check the tire
inflation pressure.
If the tire inflation pressure is
below 130 kPa (1.3 kgf/cm
2
or bar, 19 psi): The puncture
cannot be repaired. Contact
any authorized Lexus dealer
or repairer, or another duly
qualified and equipped pro-
fessional.
If the tire inflation pressure is
between 130 kPa (1.3 kgf/
cm
2 or bar, 19 psi) and a
point below the recom-
mended level: The tire can be
repaired. Proceed to .
If the tire inflation pressure is
at the recommended level:
Proceed to .
STEP 14
STEP 15
STEP 16
STEP 17

622
5-2. Steps to take in an emergency
CT200h_OM_OM76067E_(EE)Turn the compressor switch on to inflate the tire until the
recommended tire inflation pressure is reached. Drive for
about 5 km (3 miles) and then perform .
Store the kit and then attach the
2 stickers as shown.
Taking precautions to avoid
sudden braking and sharp turns,
drive carefully at under 80 km/h
(50 mph) to the nearest
authorized Lexus dealer, tire
dealer or repairer, or another
duly qualified and equipped
professional for tire repair or
replacement.
STEP 16
STEP 14
STEP 17
In the following cases, the tire cannot be repaired with the emergency tire
puncture repair kit. Contact any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional.
When the tire is damaged due to driving without sufficient air pressure
When the tire lost air pressure due to a crack or damage in the tire side-
wall
When the tire is visibly separated from the wheel
When the cut or damage to the tread is 4 mm (0.16 in.) long or more
When the wheel is damaged
When two or more tires have been punctured
When there is more than one hole or cut in the damaged tire