2006 LAND ROVER FRELANDER 2 boot

Speci al Tool (s ):
303-D121 5.
Installation 1. CAUTION: Extreme cleanli nes s mus t be exercis ed when
handl ing t hese components .
Clean and i nspect the components for det eri orati on.
1.
Inst all t he inner CV boot ont o t he halfshaft .
2.
3. NOTE: Ins t al l a new retaini ng clip.
Inst all t he inner CV joi nt inner ont o t he halfshaft .
3.
4. CAUTION: Make s ure that thes e component s are ins tall ed t o
t he noted removal pos it ion.
Inst all t he inner CV joi nt out er ont o t he halfshaft.
4.
Pack the i nner CV joint wi th the grease suppli ed.
5.
6. NOTE: Ins t al l new ret aining cl ips .
Secure t he inner CV joi nt boot t o t he inner CV joint.
6.
Inst all t he hal fs haft .
Refer t o: Front Halfs haft RH (205-04 Front Dri ve Halfs haft s , Removal
and Inst all at ion).
Refer t o: Front Halfs haft LH (205-04 Front Drive Hal fs haft s , Removal
and Inst all at ion).
7.

Publi s hed: 11-May-2011
Front Drive Halfshafts - Outer Constant Velocity (CV) Joint Boot
Removal and Inst all ati on
Special T ool(s)
303-D121Pull er, General Purpose
Removal
• NOTE: The outer cons t ant vel ocit y joint mus t not be removed from the s haft . The inner joi nt and boot have to beremoved t o all ow t he outer joi nt boot t o be replaced. The i nner and outer boots are s uppl ied t ogether as a kit .
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he hal fs haft .
Refer t o: Front Halfs haft RH (205-04 Front Dri ve Halfs haft s , Removaland Inst all at ion).Refer t o: Front Halfs haft LH (205-04 Front Drive Hal fs haft s , Removaland Inst all at ion).
2.
3. NOTE: Dis card t he ret aining cl ips .3.
4. NOTE: Dis card t he ret aining cli ps.4.

Speci al Tool (s ):
303-D121 7.
Installation 1. CAUTION: Extreme cleanli nes s mus t be exercis ed when
handl ing t hese components .
Clean and i nspect the components for det eri orati on.
1.
Inst all t he inner and out er CV boots ont o t he hal fs haft .
2.
3. NOTE: Ins t al l a new retaini ng clip.
Inst all t he inner CV joi nt inner ont o t he halfshaft .
3.
4. CAUTION: Make s ure that thes e component s are ins tall ed t o
t he noted removal pos it ion.
Inst all t he inner CV joi nt out er ont o t he halfshaft.
4.
Pack the i nner CV joint wi th the grease suppli ed.
5.
Pack the out er CV joi nt wit h t he grease s uppli ed.
6.
7. NOTE: Ins t al l new ret aining cl ips .
Secure t he inner CV joi nt boot t o t he inner CV joint.
7.
8. NOTE: Ins t al l new ret aining cl ips .
Secure t he outer CV joint boot to t he outer CV joint .
8.
Inst all t he RH halfs haft.
Refer t o: Front Halfs haft RH (205-04 Front Dri ve Halfs haft s , Removal
and Inst all at ion).
Refer t o: Front Halfs haft LH (205-04 Front Drive Hal fs haft s , Removal
and Inst all at ion).
9.

Publi s hed: 11-May-2011
Rear Drive Halfshafts -
General SpecificationItemSpecification
TypeFully fl oat ing, s ol id shafts wi th inner and out er cons tant velocit y joi nts
Recommended Lubricant
ItemSpecification
Inboard joi ntUse greas e s uppl ied wi th replacement boot kitOut board joi ntUse greas e s uppl ied wi th replacement boot kit
Torque Specifications
DescriptionNmlb-ft
Halfs haft nut*+395291* New nuts/bolts must be fitted
+ Stake nut on completion

Publi s hed: 11-May-2011
Rear Drive Halfshafts - Inner Constant Velocity (CV) Joint Boot
Removal and Inst all ati on
Special T ool(s)
303-D121Pull er, General Purpose
Removal
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he hal fs haft .
Refer t o: Rear Hal fs haft LH (205-05 Rear Dri ve Halfs haft s , Removaland Inst all at ion).
2.
3. NOTE: Dis card t he ret aining cl ips .3.
4.

5.
NOTE: Dis card t he ret aining cl ip.
5. Speci al Tool (s ):
303-D121 6.
Installation 1. CAUTION: Extreme cleanli nes s mus t be exercis ed when
handl ing t hese components .
Clean and i nspect the components for det eri orati on.
1.
Inst all t he inner CV boot ont o t he halfshaft .
2.
3. NOTE: Ins t al l a new retaini ng clip.
Inst all t he inner CV joi nt inner ont o t he halfshaft .
3.
4. CAUTION: Make s ure that thes e component s are ins tall ed t o
t he noted removal pos it ion.
Inst all t he inner CV joi nt out er ont o t he halfshaft.
4.
Pack the i nner CV joint wi th the grease suppli ed.
5.
6. NOTE: Ins t al l new ret aining cl ips .
Secure t he inner CV joi nt boot t o t he inner CV joint.
6.
Inst all t he hal fs haft .
7.

Publi s hed: 11-May-2011
Rear Drive Halfshafts - Outer Constant Velocity (CV) Joint Boot
Removal and Inst all ati on
Special T ool(s)
303-D121Pull er, General Purpose
Removal
• NOTE: The outer Const ant Veloci ty joint mus t not be removed from t he s haft. The i nner joint and gait er have t o beremoved t o faci lit ate gai ter repl acement of t he out er C. V. gai ter. The inner and out er gai ters are suppli ed toget her as akit .
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he hal fs haft .
Refer t o: Rear Hal fs haft LH (205-05 Rear Dri ve Halfs haft s , Removaland Inst all at ion).
2.
3. NOTE: Dis card t he ret aining cl ips .3.
4. NOTE: Dis card t he ret aining cli ps.4.

5.
6.
NOTE: Dis card t he ret aining cl ip.
6. Speci al Tool (s ):
303-D121 7.
Installation 1. CAUTION: Extreme cleanli nes s mus t be exercis ed when
handl ing t hese components .
Clean and i nspect the components for det eri orati on.
1.
Inst all t he inner and out er CV boots ont o t he hal fs haft .
2.
3. NOTE: Ins t al l a new retaini ng clip.
Inst all t he inner CV joi nt inner ont o t he halfshaft .
3.
4. CAUTION: Make s ure that thes e component s are ins tall ed t o
4.