2006 DODGE RAM SRT-10 engine

3.TIPM
Using a back probing tool 6801, back probe the A/C clutch power circuit in the TIPM connector.
Using a 12 volt test light connected to battery positive, check the transmission power circuit at the TIPM connector
while actuating the A/C clutch circuit with the Electronic Service Tool.
NOTE: The test light must illuminate brightly.
Compare the brightness to that of a direct connection to the battery.
Does the test light illuminate brightly?
Ye s>>
Te s t c o m p l e t e .
Perform Intermittent Condition test. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)
No>>
Replace the TIPM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

When Monitored:
With the key on.
Set Condition:
Voltage detected on the sensor supply is below a calibrated value.
Possible Causes
ECM
(F855) #1 5-VOLT SUPPLY SHORTED TO GROUND
(F855) #1 5-VOLT SUPPLY SHORTED
FUEL RAIL PRESSURE
A/C PRESSURE SENSOR
MAP SENSOR
CAMSHAFT POSITION SENSOR
INTERMITTENT CONDITION
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.ECM
Turn the ignition off.
Disconnect the ECM 60 pin harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage between the Sensor (F855) #1 5-volt Supply and
the Sensor (K916) #1 Return pin at the ECM.
Is the voltage between 4.5 and 5.5 volts?
Ye s>>
Go To 2
No>>
Replace and program the ECM in accordance with the Ser-
vice Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

2.(F855) #1 5-VOLT SUPPLY SHORTED TO GROUND
Disconnect the Pressure sensors harness connectors and the engine
position sensor.
Measure the resistance between the (F855) #1 sensor supply circuits at
the ECM harness connector and battery negative.
Is the resistance greater than 100K Ohms?
Ye s>>
Go To 3
No>>
Repair the harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
3.FUEL RAIL PRESSURE
Reconnect the ECM harness connector.
While monitoring with the scan tool, disconnect the fuel rail pressure sensor.
Is DTC P0652 set?
Ye s>>
Go To 4
No>>
Replace the Fuel rail pressure sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
4.A/C PRESSURE SENSOR
While monitoring with the scan tool, disconnect the A/C pressure sensor.
Is DTC P0652 set?
Ye s>>
Go To 5
No>>
Replace the A/C pressure sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)

5.MAP SENSOR
While monitoring with the scan tool, disconnect the map sensor.
Is DTC P0652 set?
Ye s>>
Go To 6
No>>
Replace the MAP sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
6.CAMSHAFT POSITION SENSOR
While monitoring with the scan tool, disconnect the Camshaft position sensor.
Is DTC P0652 set?
Ye s>>
Go To 7
No>>
Replace the Camshaft position sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
7.(F855) #1 5-VOLT SUPPLY SHORTED
Measure the resistance between the (F855) #1 sensor supply circuit of
the ECM harness connector and all other circuits in both ECM harness
connectors.
Is the resistance greater than 100K Ohms?
Ye s>>
Refer to the INTERMITTENT CONDITION Symptom (Diag-
nostic Procedure). (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)
No>>
Repair the shorted circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

When Monitored:
While the engine is running.
Set Condition:
Voltage detected on the sensor supply is above a calibrated value.
Possible Causes
ECM
(F855) 5-VOLT SUPPLY SHORTED TO VOLTAGE
INTERMITTENT CONDITION
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.ECM
Turn the ignition off.
Disconnect the ECM 60 pin harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage between the Sensor (F855) #1 5-volt Supply and
theSensor#1ReturnpinattheECM.
Is the voltage between 4.5 and 5.5 volts?
Ye s>>
Go To 2
No>>
Replace and program the ECM in accordance with the Ser-
vice Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

2.(F855) 5-VOLT SUPPLY SHORTED TO VOLTAGE
Key off.
Disconnect the sensor connectors for each pressure sensor, and the
engine position sensor.
Disconnect the ECM 50 way harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Ignition on, engine off.
Measure the voltage between the supply circuit at each pressure sensor
harness connector and battery negative.
Measure voltage between the (F853) 5-volt supply circuit at the engine
position sensor harness connector and battery negative.
Is the voltage less than 1 volt?
Ye s>>
Go To 3
No>>
Repair the (F855) 5-volt supply shorted to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
3.SENSOR SUPPLY SHORTED TO VOLTAGE IN HARNESS
Measure the resistance between the #1 sensor supply circuit and all
other circuit in the ECM connectors.
Is the resistance less than 10 ohms?
Ye s>>
Refer to the INTERMITTENT CONDITION Symptom (Diag-
nostic Procedure). (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)
No>>
Repair the harness shorted to voltage.

For a complete wiring diagramRefer to Section 8W.
When Monitored:
With engine running.
Set Condition:
Low voltage detected at the APPS supply circuit or low voltage detected at the APPS 1 5–volt supply.
Possible Causes
(F855) APPS 5-VOLT SUPPLY OPEN
APPS HIGH RESISTANCE
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO (K922) RETURN CIRCUIT
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO BATTERY NEGATIVE
ECM
INTERMITTENT CONDITION
(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO OTHER CIRCUITS
APPS
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
1.(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO BATTERY NEGATIVE
Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the APPS harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the APPS1 (F855) 5-volt supply circuit
between the sensor harness connector and battery negative
Is the resistance greater than 100 k ohms?
Ye s>>
Go To 2
No>>
Repair the (F855) 5-volt supply circuit shorted to battery
negative.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

2.(F855) 5-VOLT SUPPLY CIRCUIT SHORTED TO OTHER CIRCUITS
Measure the resistancebetween the (F855) APPS 1 5-volt supply circuit
at the ECM harness connector and all other circuits in the ECM con-
nector.
Is the resistance greater than 100k ohms?
Ye s>>
Go To 3
No>>
Repair the APPS #1 (F855) 5-volt supply circuit shorted to
other circuits.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
3.INTERNAL ECM
Reconnect the ECM harness connectors.
Turn ignition on, engine off.
While monitoring with the scan tool, connect a jumper wire between the
(K23) APPS 1 signal circuit at the sensor harness connector and the
(F855) APPS 1 supply circuit at the sensor harness connector.
NOTE: With the APPS disconnected it is normal to have a APPS 1
and APPS 2 low voltage DTC set.
Did a APPS 1 voltage too high DTC set?
Ye s>>
Go To 4
No>>
Replace and program the ECM in accordance with the Ser-
vice Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)