2005 NISSAN NAVARA lock

REAR SEAT
SE-33
C
D
E
F
G
H
J
K
L
MA
B
SE
1. Headrest 2. Seatback pad and frame 3. Seatback trim
4. Seat leg cover 5. Seat cushion pad and frame assem-
bly6. Seat cushion trim
7. Bushing 8. Spacer 9. Seat cushion pad and frame
10. Inboard jump seat pivot riser 11. Outboard headrest guide 12. Headrest bracket
13. Headrest holder (locked) 14. Headrest holder (free)

REAR SEAT
SE-35
C
D
E
F
G
H
J
K
L
MA
B
SE
7. Inboard pivot riser 8. Seat cushion trim 9. Seat cushion pad
10. Seat cushion pan 11. Reclining device lever knob 12. Reclining device outer cover
13. Outboard pivot riser 14. Seat cushion hinge assembly 15. Seatback frame
16. Seat lock assembly 17. Seat lock release strap 18. Headrest holder (locked)
19. Seat outer leg cover 20. Seat cushion frame assembly 21. Seat striker

SE-36
REAR SEAT
Bench Seat RH (Double Cab)
LIIA1959E
1. Headrest 2. Seat lock assembly 3. Seat lock release strap
4. Seat striker 5. Push nut 6. Armrest pad

REAR SEAT
SE-37
C
D
E
F
G
H
J
K
L
MA
B
SE
7. Armrest trim 8. Seatback pad 9. Seatback trim
10. Seatback armrest board 11. Seat cushion trim 12. Seat cushion pad
13. Seat cushion pan 14. Inboard pivot riser 15. Seat cushion bumper rubber
16. Reclining device inner cover 17. Seat cushion hinge assembly 18. Reclining device lever knob
19. Outboard pivot riser 20. Reclining device outer cover 21. Headrest holder (free)
22. Headrest holder (locked) 23. Seatback frame 24. Seat outer leg cover
25. Seat cushion frame assembly

SRS-8
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
Direct-Connect SRS Component Connectors
EHS001XF
The following SRS components use direct-connect style harness connectors.
lDriver air bag module
lFront passenger air bag module
lLH side front curtain air bag module
lLH side rear curtain air bag module
lRH side front curtain air bag module
lRH side rear curtain air bag module
lFront LH seat belt pre-tensioner
lFront RH seat belt pre-tensioner
Always pull up to release black locking tab prior to removing connector from SRS component.
Always push down to lock black locking tab after installing connector
to SRS component. When locked, the black locking tab is level with
the connector housing.
WHIA0103E

SRS-34
TROUBLE DIAGNOSIS
Trouble Diagnosis: “AIR BAG” Warning Lamp Does Not Turn OFF
EHS001XQ
DIAGNOSTIC PROCEDURE 7
1.CHECK CONDITION OF AIR BAG MODULES
Inspect for any deployed air bag modules or seat belt pre-tensioners.
Are any air bag modules or seat belt pre-tensioners deployed?
Yes >> Refer toSRS-56, "COLLISION DIAGNOSIS".
No >> GO TO 2.
2.CHECK THE AIR BAG FUSE
Check 10A fuse [No. 13, located in the fuse block (J/B)].
Refer toPG-4, "
POWER SUPPLY ROUTING CIRCUIT".
OK or NG
OK >> GO TO 4.
NG >> GO TO 3.
3.CHECK AIR BAG FUSE AGAIN
Replace 10A fuse [No. 13, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
Yes >> Repair or replace main harness.
No >> Inspection End.
4.CHECK AIR BAG DIAGNOSIS SENSOR UNIT
Connect CONSULT-II and CONSULT-II CONVERTER and touch
“START”.
Is
“AIR BAG”displayed on CONSULT-II?
Yes >>GOTO5.
No >> Visually inspect the air bag diagnosis sensor unit har-
ness connections. If the connections are OK, replace
the air bag diagnosis sensor unit. Refer toSRS-48,
"Removal and Installation".
5.CHECK HARNESS CONNECTION
Check for loose connections between the combination meter and the air bag diagnosis sensor unit.
OK or NG
OK >> Replace air bag diagnosis sensor unit. Refer toSRS-48, "Removal and Installation".
NG >> Properly connect the combination meter and air bag diagnosis sensor unit harness connectors. If
“AIR BAG” warning lamp still does not turn off, replace the wiring harness.
BCIA0030E

TROUBLE DIAGNOSIS
SRS-35
C
D
E
F
G
I
J
K
L
MA
B
SRS
Trouble Diagnosis: “AIR BAG” Warning Lamp Does Not Turn ONEHS001XR
DIAGNOSTIC PROCEDURE 8
1.CHECK METER FUSE
Check the 10A fuse [No. 14, located in the fuse block (J/B)].
Refer toPG-4, "
POWER SUPPLY ROUTING CIRCUIT".
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
2.CHECK METER FUSE AGAIN
Replace 10A fuse [No. 14, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
Yes >> Repair or replace the related harness.
No >> Inspection End.
3.CHECK HARNESS CONNECTION BETWEEN AIR BAG DIAGNOSIS SENSOR UNIT AND COMBINA-
TION METER
Disconnect the air bag diagnosis sensor unit harness connectors and turn ignition switch ON.
Does
“AIR BAG”warninglampturnON?
Yes >> Replace the air bag diagnosis sensor unit. Refer toSRS-48, "Removal and Installation".
No >> Check the combination meter power supply circuits and ground circuits. If OK, replace combina-
tion meter.

SPIRAL CABLE
SRS-39
C
D
E
F
G
I
J
K
L
MA
B
SRS
5. Disconnect lighting and turn signal switch connector. Then while
pressing tabs, pull lighting and turn signal switch toward driver
door to remove.
6. Remove the screws. Then while pressing the tab, pull the spiral
cable away from steering column assembly.
CAUTION:
lDo not disassemble spiral cable.
lDo not apply lubricant to the spiral cable.
7. Disconnect the spiral cable connectors.
CAUTION:
With the steering linkage disconnected, the spiral cable
may snap by turning the steering wheel beyond the limited
number of turns. The spiral cable can be turned counter-
clockwise about 2.5 turns from the right end position.
INSTALLATION
Install in the reverse order of removal.
lAlign spiral cable correctly when installing steering wheel, refer
toSRS-39, "
INSTALLATION". Make sure that the spiral cable is
in the neutral position. The neutral position is detected by turn-
ing left 2.6 revolutions from the right end position and ending
with the locating pin at the top.
lReset the steering angle sensor calibration after installing spiral
cable.
lAfter the work is completed, perform self-diagnosis to make sure
no malfunction is detected. Refer toSRS-18, "
SRS Operation
Check".
CAUTION:
lThe spiral cable may snap due to steering operation if the
cable is not installed in the correct position.
lWith the steering linkage disconnected, the cable may snap by turning the steering wheel beyond
the limited number of turns. The spiral cable can be turned counterclockwise about 2.5 turns from
the right end position.
LHIA0035E
LHIA0036E
LHIA0088E
PHIA0275E