2004 MITSUBISHI ENDEAVOR lock

special tool MB990939 and a hammer to tap the bolt in the desired
direction.
Fig. 9: Adjusting Lock

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Adjustment by using the striker (toward the outside of the vehicle)
Use special tools MB990211 and MB990243 to pull the striker toward the
outside of the vehicle.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Fig. 13: Identifying Run Channel, Lower Sash And Door Sas
h
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
5. If repair or adjustment is not possible, replace the door assembly.
POWER WINDOW TIMER FUNCTION CHECK After the doors are closed and the ignition switch is turned to the "LOCK" (OFF)
position, the power windows should work within 30 seconds. The timer expires if
the front door is opened during that 30 second time. If it does not, carry out the
timer troubleshooting in SYMPTOM CHART
.
POWER WINDOW OPERATING CURRENT CHECK 1. Remove the power window fuse and connect an ammeter as shown in the
illustration.
2. When the power window switch is pressed in the "UP" position, a large amoun
t
of current flows from the time the window starts to close until it is fully closed,
Measure the current during this time
Standard value (A): 5 +/-1A [Power supply voltage 14.5 +/-0.5V, 25°C (77°
F)]
3. If the operation current is outside the standard value, refer to INPUT SIGNAL
CHART
.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
CIRCUIT BREAKER (INCORPORATED IN THE POWER WINDOW MOTOR) INSPECTION 1. Pull the power window switch to the UP position to fully close the door
window glass, and keep pulling the switch for an additional ten seconds.
2. Release the power window switch from the UP position and immediately press
it to the DOWN position. The condition of the circuit breaker is good if the
door window glass starts to move downwards within about 60 seconds. POWER WINDOW CHECK 1. Operate the power window switch of each door to verify that the power
windows operate properly. If they don't, then troubleshoot as described in
SYMPTOM CHART
.
2. Turn ON the power window lock switch of the power window main switch.
Then operate the passenger's door and rear door power window sub-switches to
ensure that they do not operate. If they do, replace the power window main
switch (Refer to DOOR GLASS AND REGULATOR
).
CENTRAL DOOR LOCKING SYSTEM INSPECTION Check the following. Troubleshoot if operations malfunction (Refer to SYMPTOM CHART
).
Insert the key into the driver's key cylinder and turn once to the unlock side to
unlock the driver's door. Turn the key once again to the unlock side to unlock
all doors and the liftgate. All doors and liftgate can be locked using the door lock switch built into the
front power window (main or sub < RH>) switch.
DOOR OUTSIDE HANDLE PLAY CHECK 1. Check that the door outside handle play is within the standard value range.
Standard value (B):
Front door: 10 +/- 3.5 mm (0.39 +/- 0.138 inch)
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

SWITCH POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
FRONT (LH)
UP
8-13, 9-12,
Less than 2 ohms
OFF
8-12, 9-12
Less than 2 ohms
DOWN
9-13, 8-12
Less than 2 ohms
FRONT (RH)
UP
3-13, 11-12*
Less than 2 ohms
OFF
3-11, 3-12*, 11-12*
Less than 2 ohms
DOWN
11-13, 3-12*
Less than 2 ohms
REAR (LH)
UP
1-13, 2-12*
Less than 2 ohms
OFF
1-2, 1-12*, 2-12*
Less than 2 ohms
DOWN
2-13, 1-12*
Less than 2 ohms
REAR (RH)
UP
13-14, 6-12*
Less than 2 ohms
OFF
6-14, 6-12*, 12*--14
Less than 2 ohms
DOWN
6-13, 12*--14
Less than 2 ohms
NOTE: *: Set the window lock switch to UNLOCK position.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
>>B<< LOWER SASH INSTALLATION Securely insert the lower sash into the window rear sash. INSPECTION FRONT DOOR LATCH CHECK The illustration shows when the door lock actuator is viewed from inside the door. DOOR LOCK ACTUATOR INCORPORATED IN DOOR LATCH CHECK < LEFT SIDE> FRONT DOOR LATCH CHECK SPECIFICATION LEVER POSITION
BATTERY
CONNECTION
LEVER OPERATION
At the "UNLOCK"
position
Connect terminal No.
4 and the negative
battery terminal. Connect terminal No.
6 and the positive
battery terminal.
The lever moves from
the "UNLOCK" position
to the "LOCK" position.
At the "LOCK" position
Connect terminal No.
6 and the negative
battery terminal. Connect terminal No.
4 and the positive
battery terminal.
The lever moves from
the "LOCK" position to
the "UNLOCK"
position.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Fig. 34: Identifying Lock And Lever Of Front Door Latch Check (Front Door)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
DOOR LOCK ACTUATOR SWITCH INCORPORATED IN DOOR LATCH CHECK < LEFT SIDE> DOOR LOCK ACTUATOR SWITCH SPECIFICATION DOOR LOCK ACTUATOR INCORPORATED IN DOOR LATCH CHECK < RIGHT SIDE> DOOR LOCK ACTUATOR LATCH CHECK DOOR LOCK ACTUATOR SWITCH INCORPORATED IN DOOR LATCH CHECK < RIGHT SIDE> DOOR LOCK ACTUATOR SWITCH CHECK LEVER POSITION
TESTER CONNECTION
SPECIFIED
CONDITION
At the "LOCK" position
1-2
Open circuit
At the "UNLOCK"
position
1-2
Less than 2 ohms
LEVER POSITION
BATTERY
CONNECTION
LEVER OPERATION
At the "LOCK" position
Connect terminal No.
4 and the negative
battery terminal. Connect terminal No.
6 and the positive
battery terminal.
The lever moves from
the "LOCK" position to
the "UNLOCK"
position.
At the "UNLOCK"
position
Connect terminal No.
6 and the negative
battery terminal. Connect terminal No.
4 and the positive
battery terminal.
The lever moves from
the "UNLOCK" position
to the "LOCK" position.
LEVER POSITION
TESTER CONNECTION
SPECIFIED
CONDITION
At the "LOCK" position
2-3
Open circuit

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

REAR DOOR LOCK ACTUATOR CHECK The illustration shows when the door lock actuator is viewed from outside the door. DOOR LOCK ACTUATOR INCORPORATED IN DOOR LATCH CHECK < LEFT SIDE> DOOR LOCK ACTUATOR LATCH CHECK At the "UNLOCK"
position
2-3
Less than 2 ohms
LEVER POSITION
BATTERY
CONNECTION
LEVER OPERATION
At the "LOCK" position
Connect terminal No.
4 and the negative
battery terminal. Connect terminal No.
6 and the positive
battery terminal.
The lever moves from
the "LOCK" position to
the "UNLOCK"
position.
At the "UNLOCK"
position
Connect terminal No.
6 and the negative
battery terminal. Connect terminal No.
4 and the positive
battery terminal.
The lever moves from
the "UNLOCK" position
to the "LOCK" position.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

Fig. 35: Identifying Lock And Lever Of Front Door Latch Check (Rear Door)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
DOOR LOCK ACTUATOR SWITCH INCORPORATED IN DOOR LATCH CHECK < VEHICLES WITH THEFT ALARM
SYSTEM (LEFT SIDE)> DOOR LOCK ACTUATOR SWITCH LATCH CHECK DOOR LOCK ACTUATOR INCORPORATED IN DOOR LATCH CHECK < RIGHT SIDE> DOOR LOCK ACTUATOR LATCH CHECK DOOR LOCK ACTUATOR SWITCH INCORPORATED IN DOOR LATCH CHECK < VEHICLES WITH THEFT ALARM
SYSTEM (RIGHT SIDE)> DOOR LOCK ACTUATOR SWITCH LATCH CHECK LEVER POSITION
TESTER CONNECTION
SPECIFIED
CONDITION
At the "LOCK" position
2-3
Open circuit
At the "UNLOCK"
position
2-3
Less than 2 ohms
LEVER POSITION
BATTERY
CONNECTION
LEVER OPERATION
At the "UNLOCK"
position
Connect terminal No.
4 and the negative
battery terminal. Connect terminal No.
5 and the positive
battery terminal.
The lever moves from
the "UNLOCK" position
to the "LOCK" position.
At the "LOCK" position
Connect terminal No.
6 and the negative
battery terminal. Connect terminal No.
4 and the positive
battery terminal.
The lever moves from
the "LOCK" position to
the "UNLOCK"
position.
LEVER POSITION
TESTER CONNECTION
SPECIFIED
CONDITION

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor